Instrukcja obsługi System Sensor BEAM-MMK
System Sensor
detektor
BEAM-MMK
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla System Sensor BEAM-MMK (2 stron) w kategorii detektor. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
1 I56-2358-004
06-10
INSTALLATION AND MAINTENANCE INSTRUCTIONS
BEAMMMK
Multi-mounting Kit for use with
Reective Projected Beam Smoke Detectors
3825 Ohio Avenue, St. Charles, Illinois 60174
800/736-7672, FAX: 630/377-6495
www.systemsensor.com
MOUNTING AND WIRING INSTRUCTIONS:
TRANSMITTER/RECEIVER
The BEAMSMK accessory must be used with the transmitter/receiver to pro-
vide wiring entry. Refer to Figures 2 through 4 for this step.
1. Read the installation instructions of the beam detector to determine the
appropriate size and number of wires to be used.
2. Drill the appropriate holes for the flexible conduit using the drill centers
provided on either the sides or the back of the surface mount base. See
Figure 2 for details. Note that the top of the surface mount base contains
mounting bosses for the “L” brackets used in the next step. Conduit sizes
of 1/2″ or 3/4″ are acceptable.
3. Assemble the “L” brackets to the surface mount base using the two #10-
24 × 5/8″ screws and two #10 split-lock washers provided. See Figure 3 for
details. The screws should be fully tightened.
4. Assemble the “U” bracket to the “L” brackets using the two #10-24 ×
1/2″ screws and fender washers provided. See Figure 3 for details. The
“U” bracket should be assembled to the “L” brackets so that the words
“DO NOT PAINT” appear in the front of the assembly. Tighten the screws
until almost snug. The assembly should tilt freely in either direction. The
screws will be fully tightened later when the alignment is performed.
5. Insert the flange of the “U” bracket into the keyed hole of the wall or ceil-
ing mount bracket. Slide the bracket forward into position. The surface
mount base should now hang from the bracket.
6. Insert the correct screw and washer combination (either wall or ceil-
ing mount) through the slot and into the hole of the mounting bracket
flange. Tighten the screw until almost snug. The assembly should still
Notice: This manual should be left with the owner/user of this equipment.
GENERAL DESCRIPTION
The BEAMMMK allows reflected beam detectors and reflectors to be mounted
to either a vertical wall or the ceiling. The kit allows for additional alignment
range in cases where the detector and reflector cannot be mounted within
10° of each other. The kit includes the hardware necessary to mount either
a single transmitter/receiver unit or a single reflector. (To mount the trans-
mitter/receiver the surface mount kit, BEAMSMK, must also be used). If the
transmitter/receiver and the reflector require additional alignment range two
kits are required. The kit is not compatible with the long-range reflector kit
(BEAMLRK).
The kit includes the following parts:
Qty. Description
1 Ceiling mount bracket inside
1 Ceiling mount bracket outside
1 Wall mount bracket
1 “U” bracket
2 “L” bracket
1 Horizontal adjustment screw (ceiling) #10-24 × 2 1
/
4″
1 Horizontal adjustment screw (wall) #10-24 × 13/
8″
2 Allen screw #10-24 × 1
/2″
2 Allen screw #10-24 × 5
/8″
2 Fender washer plastic
2 Fender washer metal
2 Washer plastic #10
2 Washer metal #10
2 Washer metal split-lock #10
2 Hex nut #10-24
1 Allen wrench
MOUNTING BRACKETS
Install a ceiling or wall bracket so that when mounted, the transmitter/re-
ceiver and the reflector will have a clear line of sight between them.
The ceiling bracket is composed of two parts that should be assembled with
the inside part between the ceiling and the outside part as shown in Figure 1.
The brackets should be mounted so that the slot in the front of each bracket
is facing the other bracket. Mount the brackets only on solid structures of the
building. To avoid unwanted alarms due to wall movement, do not mount to
flexible walls, such as sheet metal walls (see Mounting Locations section of
the transmitter/receiver manual for more details).
CEILING
SCREWS
SLOT IN FRONT
OF BRACKET
OUTSIDE
PART
INSIDE
PART
CEILING
FIGURE 1. CEILING MOUNT BRACKET ASSEMBLY:
C0315-00
I56-2358-004
2 I56-2358-004
©2016 System Sensor. 06-10
turn freely in both directions. The screw will be fully tightened later
when the alignment is performed.
7. Pull the wiring and the flexible conduit through the drilled hole(s). At-
tach nut(s) (not included) to conduit fitting and tighten.
NOTE: Be sure to leave enough wire to reach the transmitter/receiver unit
when attached to the surface mount base. Be sure to leave enough flexible
conduit so that the transmitter/receiver unit can be adjusted to aim at the
reflector.
8. Attach the transmitter/receiver unit securely to the base using the four
#8-32 × 1/2″ screws supplied with the BEAMSMK accessory.
9. Adjust the transmitter/receiver unit so that it is aiming directly at the
reflector. Once aimed correctly fully tighten both vertical and horizontal
adjustment screws.
NOTE: For proper operation of the beam detector it must be securely mounted
to ensure no subsequent movement of the beam detector will occur after the
installation is completed. See “Detector Placement and Mounting” sections of
the beam detector manual for further details.
10. Complete the installation of the transmitter/receiver unit using the instruc-
tions included with the beam detector.
11. Test the system as indicated in the beam detector instructions.
MOUNTING INSTRUCTIONS: REFLECTOR
Refer to Figure 4 for this step.
1. Assemble the “L” brackets to the reflector using the two #10-24 ×
5/8″
screws, two #10 split-lock washers, and two #10 locknuts provided. See
Figure 4 for details. The screws should be fully tightened.
2. Assemble the “U” bracket to the “L” brackets using the two #10-24 ×
1/2″ screws and fender washers provided. See Figure 4 for details. The
“U” bracket should be assembled to the “L” brackets so that the words
“DO NOT PAINT” appear in the front of the assembly. Tighten the screws
until almost snug. The assembly should tilt freely in either direction. The
screws will be fully tightened later when the alignment is performed.
3. Insert the flange of the “U” bracket into the keyed hole of the wall or ceil-
ing mount bracket. Slide the bracket forward into position. The reflector
should now hang from the bracket.
4. Insert the correct screw and washer combination (either wall or ceil-
ing mount) through the slot and into the hole of the mounting bracket
flange. Tighten the screw until almost snug. The assembly should still
turn freely in both directions. The screw will be fully tightened later
when the alignment is performed.
5. Adjust the reflector so that it is aiming directly at the transmitter/receiver
unit. Once aimed correctly fully tighten both vertical and horizontal ad-
justment screws.
NOTE: For proper operation of the beam detector the reflector must be se-
curely mounted to ensure no subsequent movement will occur after the instal-
lation is completed. See “Detector Placement and Mounting” sections of the
beam detector manual for further details.
6. Test the system as indicated in the beam detector instructions.
FIGURE 2. BEAMSMK WIRING LOCATIONS:
FIGURE 3. WALL MOUNTING TRANSMITTER/RECEIVER UNIT:
Fender Washer – Metal
Fender Washer – Plastic
Vertical Adjustment
Screw #10-24 ×1/2″
#10-24 ×5/8″
#10 Split-lock Washer
“L” Bracket
DO NOT PAINTDO NOT PAINT
Horizontal
Adjustment Screw
#10-24 1×3/8″Metal Washer
Mounting Hub
“U” Bracket
Wall Mounting
Bracket
Mounting Hole
Plastic Washer
C0312-00
Drill for conduit
C0318-00
FIGURE 4. CEILING MOUNTING REFLECTOR:
DO NOT PAINT
DO NOT PAINT
Fender Washer– Metal
Fender W
asher – Plastic
Vertical Adjustment
Screw #10-24 ×1
/2″
#10 Hex Nut
#10 Split-lock Washer
“L” Bracket
Horizontal
Adjustment Screw
#10-24 2×1/4″Metal Washer
Mounting Hub
“U” Bracket
Mounting Holes
Plastic Washer
#10-24 ×5/8″
C0313-00
Specyfikacje produktu
| Marka: | System Sensor |
| Kategoria: | detektor |
| Model: | BEAM-MMK |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z System Sensor BEAM-MMK, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje detektor System Sensor
23 Września 2024
20 Września 2024
18 Września 2024
11 Września 2024
11 Września 2024
Instrukcje detektor
- detektor Joy-It
- detektor Voltcraft
- detektor Dometic
- detektor Bosch
- detektor Gigaset
- detektor Hikvision
- detektor Nedis
- detektor Nexa
- detektor Black & Decker
- detektor Marquant
- detektor Evolveo
- detektor Silverline
- detektor Honeywell
- detektor Mercury
- detektor Testo
- detektor ORNO
- detektor DSC
- detektor Cobra
- detektor Vimar
- detektor V-TAC
- detektor Dahua Technology
- detektor Trotec
- detektor Uniden
- detektor Velleman
- detektor Homematic IP
- detektor Pyle
- detektor Edimax
- detektor Grothe
- detektor National Geographic
- detektor Ferrex
- detektor Axis
- detektor Abus
- detektor Olympia
- detektor Netatmo
- detektor Optex
- detektor Schwaiger
- detektor ZKTeco
- detektor Extech
- detektor Denver
- detektor Garrett
- detektor Kyoritsu
- detektor Busch-Jaeger
- detektor Powerfix
- detektor Alecto
- detektor JUNG
- detektor X-Sense
- detektor HT Instruments
- detektor Smartwares
- detektor Skyscan
- detektor Inovonics
- detektor Soler & Palau
- detektor Amprobe
- detektor Sun Joe
- detektor Ei Electronics
- detektor Techly
- detektor Flir
- detektor Royal Sovereign
- detektor AcuRite
- detektor Safescan
- detektor FireAngel
- detektor X4-Tech
- detektor Iget
- detektor Popp
- detektor Satel
- detektor Multimetrix
- detektor Gamma Scout
- detektor Ebode
- detektor Escort
- detektor Guardian Avionics
- detektor Thitronik
- detektor Whistler
- detektor Cavius
- detektor Pentatech
- detektor Flow Smoke Detector
- detektor Benewake
- detektor BeeSecure
- detektor Fisher
- detektor SureCall
- detektor Schabus
- detektor Zircon
- detektor Sanwa
- detektor Resideo
- detektor STI
- detektor BlendMount
- detektor K40
- detektor Gewiss
- detektor Seco-Larm
- detektor Silent Knight
- detektor GEV
- detektor S.E. International
- detektor Rocky Mountain
- detektor Winland
- detektor Noyafa
Najnowsze instrukcje dla detektor
9 Października 2024
9 Października 2024
9 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024