Instrukcja obsługi StarTech.com POEINJ1G90W

StarTech.com Wzmacniacz sygnału WiFi POEINJ1G90W

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla StarTech.com POEINJ1G90W (2 stron) w kategorii Wzmacniacz sygnału WiFi. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: June 2, 2020 11:37 AM

Product Diagram (POEINJ1G90W)

Component Function

1Power LEDs • A is detected.Green: Power Source

• A is not detected.O: Power Source

2PoE LED

• Indicates that the is Amber: PoE Injector

providing power.

• Indicates that the is in idle O: PoE Injector

mode.

3PoE Out Port • Connect a (PD) to the Powered Device PoE

Injector.

4Data Port • Connect a to the Network Switch PoE

Injector.

54-Pin Terminal Block

V1 and V2

• Connect an external (48-56V DC Power Source

DC Input) to the .PoE Injector

6Ground Screw

• Connect a ground connection to the Ground

Screw DC Power Source when connecting a to

the .PoE Injector

Requirements

For the latest requirements, please visit www.startech.com/POEINJ1G90W

• Small Flat Head Screwdriver x 1

• (Optional) Phillips® Head Screwdriver x 1

• (Optional) Writing Utensil x 1

• PoE Powered Device (PD) x 1

• Network Switch x 1

• DC Power Source or Universal Power Adapter with Type N (OD: 5.5 mm, ID: 2.5 mm)

Barrel Connector x 1

90W Industrial Grade Hardened 802.3bt PoE Injector | 1G (1000 Mbps)

• RJ45 Terminated UTP/STP Cat 5e (or better) Network Cable x 2

Powering the PoE Injector

Terminal Block

Connecting and installing the , must be completed by a 4-Wire Terminal Connector

licensed Electrician.

Notes: Make sure that you turn o the power source before connecting the power wire

to the .PoE Injector

Do not exceed the recommend power source voltage as it may result in personal or

product damage.

1. Using a , loosen the two screws (V1 or V2) on the Small Flat Head Screwdriver

4-Wire Terminal Connector (included).

2. Connect the from a (48 - 56V DC), or the provided Power Wires DC Power Source

Barrel Power Connector Adapter, Terminal Block Connectorsto the proper to

the terminals are marked on the . Connect the positive wire to PoE Injector’s Casing

V+ and the negative wire to V-.

3. Tighten the two screws on the .4-Wire Terminal Connector

4. Insert the in the on the 4-Wire Terminal Connector 4-Wire Terminal Block PoE

Injector.

5. To connect a second to the , repeat steps 1 - 4.Power Source PoE Injector

6. Using a , loosen the on the .Phillips Head Screwdriver Ground Screw PoE Injector

7. Connect the from a to the on the Ground Wire DC Power Source Ground Screw

PoE Injector.

8. Using the , tighten the to secure thePhillips Head Screwdriver Ground Screw

Grounding Wire PoE Injectorto the .

(Optional) Barrel Connector

• Connect a from a Type N (OD: 5.5 mm, ID: 2.5 mm) Barrel Connector Universal

Power Adapter Terminal Block to Barrel Power Connector Adapter. to the

Connecting the PoE Injector

Notes: Make sure the total length of the connecting the CAT5e/6 Cable PD Device

to the and the connecting the to the PoE Injector CAT5e/6 Cable PoE Injector

Remote Switch does not exceed 100 meters in total length.

The is compatible with both Power over Ethernet (PoE) and 95W Power PoE Injector

over HDBaseT (PoH).

1 2 34 5 6

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated

in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of

this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

Changes or modications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.

Industry Canada Statement

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (A)/NMB-3(A)

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the

property of their respective holders.

Warranty Information

This product is backed by a two-year warranty.

For further information on product warranty terms and conditions, please refer to .www.startech.com/warranty

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)

for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of

business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations

or exclusions contained in this statement may not apply to you.

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

安全対策

• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

Misure di sicurezza

• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

FR: startech.com/fr

DE: startech.com/de

ES: startech.com/es

NL: startech.com/nl

IT: startech.com/it

JP: startech.com/jp

StarTech.com Ltd.

45 Artisans Cres

London, Ontario

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Rd,

Brackmills

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

2500 Creekside

Parkwy

Lockbourne, Ohio

43137

U.S.A.

7. Insert the (x 2) through the on the Mounting Screws Mounting Holes PoE Injector

and into the .Wall

8. Using a , tighten the until the Phillips Head Screwdriver Mounting Screws PoE

Injector Wall is securely fasten to the .

Product Dimensions

1. Connect a to the on the and the other CAT5e/6 Cable PoE Out Port PoE Injector

end to an RJ45 port on a (e.g. security camera, etc.).PoE PD Device

2. Connect a to the on the and the other end to CAT5e/6 Cable Data Port PoE Injector

an RJ45 port on a .Network Switch

Mounting

DIN Rail Mounting

1. Align the (x 1) with the (x 4) on the side of the DIN Rail Brackets Mounting Holes

PoE Injector.

2. Insert the (x 3) through the and into the Mounting Screws DIN Rail Bracket PoE

Injector.

3. Using a , tighten the . Be careful not to Phillips Head Screwdriver Mounting Screws

over-tighten the .Mounting Screws

4. Clip the onto a , securing the .DIN Rail Bracket DIN Rail PoE Injector

Wall Mounting

It is recommended that you use when wall mounting the .Wall Studs PoE Injector

1. Align the (x 2) with the (x 4) on the side of the Mounting Brackets Mounting Holes

PoE Injector.

2. Insert the (x 4) through each of the and into Mounting Screws Mounting Brackets

the .PoE Injector

3. Align the on the wall in the position you want to mount the PoE Injector PoE

Injector.

4. Using a , mark o both on the .Writing Utensil Mounting Holes PoE Injector

5. Using a , draw a line connecting the two , making sure that the Level Mounting Holes

line is level.

6. Align the on the with the .Mounting Holes PoE Injector Mounting Hole Marks

Specyfikacje produktu

Marka:	StarTech.com
Kategoria:	Wzmacniacz sygnału WiFi
Model:	POEINJ1G90W

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z StarTech.com POEINJ1G90W, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Wzmacniacz sygnału WiFi StarTech.com

StarTech.com C2-ETHERNET-EXTENDER Instrukcja

5 Października 2024

StarTech.com VDSL-LAN-EXTENDER-1G Instrukcja

4 Października 2024

StarTech.com UPOESPLT1G Instrukcja

22 Września 2024

StarTech.com AP300WN2X2W Instrukcja

22 Września 2024

StarTech.com USB110EXT Instrukcja

21 Września 2024

StarTech.com R300WN22MOD5 Instrukcja

21 Września 2024

StarTech.com 10/100 VDSL2 Instrukcja

20 Września 2024

StarTech.com POEEXT2GAT Instrukcja

20 Września 2024

StarTech.com 110VDSLEXT Instrukcja

19 Września 2024

StarTech.com HDBOOST4K Instrukcja

18 Września 2024

Instrukcje Wzmacniacz sygnału WiFi

Najnowsze instrukcje dla Wzmacniacz sygnału WiFi

Mercusys ME80X Instrukcja

24 Marca 2025

Ubiquiti Networks UniFi Device Bridge Instrukcja

21 Lutego 2025

Icron USB 2.0 Ranger 2304PoE Instrukcja

20 Lutego 2025

Icron USB Ranger 2204 Instrukcja

20 Lutego 2025

Ubiquiti Networks UniFi Device Bridge Pro Instrukcja

20 Lutego 2025

Axis C8110 Instrukcja

20 Lutego 2025

Tenda A18 Pro Instrukcja

5 Lutego 2025

Strong Repeater 300 V2 Instrukcja

5 Lutego 2025

TP-Link RE220 Instrukcja

12 Stycznia 2025

Manhattan 525664 Instrukcja

12 Stycznia 2025