Instrukcja obsługi StarTech.com AP300WN2X2W


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla StarTech.com AP300WN2X2W (2 stron) w kategorii Wzmacniacz sygnału WiFi. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
Quick Start Guide
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
I T: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
P T: Guia do usuário - pt.startech.com
Manual Revision: 08/07/2014
For the most up-to-date information, please visit: www.startech.com
Packaging Contents
1 x In-Wall Access Point
1 x Faceplate
1 x Frame for Faceplate
2 x Screws
2 x Washers
1 x Quick Start Guide
1 x Instruction Manual CD
System Requirements
802.3af / at compatible PoE Switch
Cat 5e (or better) Ethernet cabling from PoE switch to the Access
Point
1 gang receptacle box
LED Indicators
Installation
AP300WN2X2W / AP300WN22WUE
300Mbps Wireless N PoE-Powered Wallplate Access Point
*actual product may vary from photos
Front View
Rear View
Reset Procedure
Default Settings
To reset the unit to factory defaults, press and hold the AUX and
Reset buttons simultaneously for 5 seconds and then release.
Default IP Address: 10.59.1.200
Username / Password: admin / admin
1. Slide the Frame over the back of the AP and secure using the
provided screws w/ washers.
Ethernet Connector
(transparent) LAN Connector AUX Reset
Button
PoE Power / Data
Connector Ethernet Connector
(transparent)
LED DescriptionState
PWR O No power
Green Unit powered on
SYS
O Remains o while the unit is initializing
Green Initializing complete, system is ready to use
Green (Blinking) During rmware upgrades, this system LED will blink
Link/
WAN
O No network connector
Green 10/100Mbps network connection established
Green (Blinking) Indicates WAN activity
LAN
O No network connection
Green 10/100Mbps network connection established
Green (Blinking) Indicates LAN activity
WLAN
O The Wireless is not ready
Green Wireless connection established
Green (Blinking) Indicates Wireless activity
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation
of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2)l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.Déclaration d’exposition à la radiation: Cet équipement
respecte les limites d’exposition aux rayonnements IC dénies pour un environnement non contrôlé. Cet équipement doit être installé et mis en marche à une distance minimale de 20 cm qui sépare l’élément rayonnant de votre corps.Lémetteur ne doit ni être utilisé avec une autre
antenne ou un autre émetteur ni se trouver à leur proximité.
FCC ID: TWS-WAP-001R2
IC: 11232A-AP300WN2X2W
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent
an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement with equivalent products at our discretion. The
warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss, arising
out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
2. Connect an Ethernet cable to the PoE power / data port on the
back of the AP.
3. (Optional) Connect a second Ethernet cable or RJ11 telephone
cable to the transparent Ethernet pass-through port if desired for
telephony or secondary LAN connection.
4. Insert the AP into a standard 1 gang outlet box until it sits ush
with the wall and secure with screws.
5. Attach the Faceplate to the front of the AP and press in so that it
clips into place.
Operation
For complete operating instructions / specications, please visit
www.startech.com/AP300WN2X2W
1. Congure a system to be on the same subnet as the AP (e.g.
10.59.1.8 - 254).
2. Open your preferred web browser and enter the IP address
10.59.1.200 into the address bar, then press Enter.
3. Enter your Username / Password (Default: ) and admin / admin
click Login.
4. Select the section from the left column of the Network Setting
web interface to congure your desired IP address settings and
VLAN information. Click to save your changes.Apply
5. To change the available SSID information and wireless security
settings, select Wireless Setting > Multi-SSID Setting > Edit on
each individual SSID that you would like to enable. Click Apply to
save your changes.
Note: It is strongly recommended to congure security, to avoid
unwanted access to your wireless network.
6. To restrict access to the web interface of your AP, it is also
recommended to congure a password, which can be done by
selecting the Administration Setting section. Click Apply to save
your changes.
Note: It is strongly recommended to change the default security
settings, to avoid unwanted access and/or conguration changes.


Specyfikacje produktu

Marka: StarTech.com
Kategoria: Wzmacniacz sygnału WiFi
Model: AP300WN2X2W

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z StarTech.com AP300WN2X2W, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Wzmacniacz sygnału WiFi StarTech.com

Instrukcje Wzmacniacz sygnału WiFi

Najnowsze instrukcje dla Wzmacniacz sygnału WiFi

Planet

Planet WNAP-1110 Instrukcja

10 Października 2024
Netgear

Netgear WN2000RPTv2 Instrukcja

10 Października 2024
Xiaomi

Xiaomi RA75 Instrukcja

9 Października 2024
Cudy

Cudy RE3000 Instrukcja

8 Października 2024
Cudy

Cudy RE1200 Instrukcja

8 Października 2024
Netgear

Netgear EX6170 Instrukcja

8 Października 2024
Extron

Extron FOX 3G HD-SDI SM Instrukcja

8 Października 2024
Extron

Extron FOXBOX Rx VGA MM Instrukcja

8 Października 2024