Instrukcja obsługi StarTech.com C2-ETHERNET-EXTENDER

StarTech.com Wzmacniacz sygnału WiFi C2-ETHERNET-EXTENDER

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla StarTech.com C2-ETHERNET-EXTENDER (3 stron) w kategorii Wzmacniacz sygnału WiFi. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: April 11, 2024

Product ID

C2-ETHERNET-EXTENDER

Front View

Component Function

1ON/OFF Position • Sets a specied orDIP Switch ON OFF

2DIP Switches

• Select the desired change for (1) Link Fault Pass-Through

(LFPT) (2) Link Speed (3) Local/Remote , , or mode

Note: Keep the DIP Switch 4 in the OFF position at all times to

prevent undesired behavior.

LFPT Note: If a link between two units is lost, one unit may

continue to send packets assuming the link is up, potentially

leading to data loss. LFPT minimizes this risk by forcing a link

down state upon link failure.

3LAN Port

• Connects the unit to the orLocal Local Network Host

Device/Computer RJ45 UTP Cablevia

• Connects the unit to a orRemote Remote Network

IP-Based Device RJ45 UTP Cablevia

4LED Indicators • Indicate the status of , , , Local/Remote Power Link Status

Link Speed LFPT, and

5LINE Port • Connects the and units to each other using Local Remote

RJ45 RJ11UTP Cable or

6DC Power Port

(At the Back)

• Connect to a using the included Power Source Power

Adapter

• Recommended 12V and 1A

• Type M barrel plug: Ø 5.5x2.1x9.5mm

10/100 Base-TX Ethernet Extender Kit - Extend up to 2,624ft (800m)

LED Indicators

LED Color ON OFF

Local Green Local Mode is ON Auto Mode

PWR Green Unit is receiving power Unit is not receiving power

LAN Link Green LAN Link Up LAN Link is Down

100M Green Local to Remote Link is

operating at 100Mbps

Local to Remote unit Link

is operating at 10Mbps or

is Down

LFPT Green

LFPT function is ON,

and a LAN Link Fault has

occurred

LFPT function is OFF or

LFPT function is ON, and

no LAN Link Fault has

occurred

10M Green Local to Remote Link is

operating at 10Mbps

Local to Remote unit Link

is operating at 100Mbps or

is Down

Package Contents

• Ethernet Extender x 2

• Power Adapter x 2

• Mounting Bracket x 2

• Mounting Screws x 4

• Quick-Start Guide x 1

Requirements

For the latest requirements, please visit www.startech.com/C2-ETHERNET-EXTENDER

• RJ45 terminated UTP/STP Cat5e (or better) Ethernet cable (sold separately)

• Phillips head screwdriver

*Product may vary from image

Note: If the DIP Switches need to be adjusted after the initial setup, both units must be

Powered O before changing the DIP Switch settings.

Install the Ethernet Extender Kit

1. Adjust the according to the needs of the setup.DIP Switches

2. Position the units in each of the deployment locations, and .Local Remote

3. Plug in an from the on the unit to an RJ45 Patch Cable LAN Port Local Extender

Ethernet Port Local Network Host Device/Computer on a or a .

4. Plug in an from the on the unit to an RJ45 Patch Cable LAN Port Remote Extender

Ethernet Port Remote Network IP-Based Deviceon a or .

5. Plug in a terminated or from the on the RJ45 RJ11 UTP Cable Line PortLocal

Extender Line Port Remote Extender unit to the on the unit.

6. Connect the included to the on the andPower Adapter DC Power Port Local

Remote units.

Mounting the Local and Remote Units

Warning!

The mounting hardware included with this product may not be adequate for some

wall structures. If lacking the necessary expertise to wall mount this product, contact

a construction professional to install the mounting hardware or to provide specic

mounting instructions for the wall structure.

Note: Use one of the Wall Mount Brackets as a template to mark the Holes to be

drilled on the Wall or Mounting Surface.

1. Align the holes in the with the holes on the of the Wall Mount Brackets Bottom

Local Remote or units.

2. Insert the Mounting (x 2) through the and into the Screws Wall Mount Bracket

Local Remote or unit. (Figure 1)

Figure 1

3. Tighten the using a . Mounting Screws Phillips Head Screwdriver

4. Use the (x 2) on the to attach the orKey Holes Wall Mount Brackets Local Remote

unit to the (x 2) on the or . Screws Wall Mounting Surface

5. Repeat to with the remaining unit. Steps 1 4

Installation

Extension Distance and Link Speed

Extension Distance ft (m)

Cat5e or Cat6 UTP Link speed (Mbps)

2 Pairs 1 Pair

328ft (100m) 100Mbps 100Mbps

656.1ft (200m) 100Mbps 100Mbps

984.2ft (300m) 100Mbps 100Mbps

1312.3 (400m) 100Mbps 10Mbps

1640.4 (500m) 100Mbps 10Mbps

2296.5ft (600m) 100Mbps 10Mbps

2296.5ft (700m) 10Mbps 10Mbps

2624.6ft (800m) 10Mbps 10Mbps

Note: Either Unit can be the Local or Remote Unit.

If the Link Speed is set to 10Mbps it will limit the speed regardless of distance and

number of pairs in the UTP Cable used.

DIP Switches

DIP Switch ON OFF

1 - LFPT

When the Remote Unit's

Network Link Down is the

Network Link Local of the unit

will be Forced Down

Disables LFPT

2 - Link Speed Forces the to Link Speed

10Mbps

Auto-selects the Link Speed

between 10 or 100Mbps

depending on the Extension

Distance Pairsand number of

of usedUTP Cable

3 - Local/Remote

Forces either of the units to

Local Mode

Note: Only one unit must be

set to Local mode

Auto-selects the and Local

Remote unit (factory default)

4 - No Function -

Leave to Permanently OFF

connect the to DIP Switch

ground

Quick-Start Guide

exceed the actual price paid for the product. Some States do not allow the exclusion

or limitation of incidental or consequential damages. If such laws apply, the limitations

or exclusions contained in this statement may not apply to you.

Safety Measures

EN: Do not touch the product under power if the product has an exposed printed

circuit board or electrical wire.

Warning: please consult the online manual for detailed safety instructions.

NL: Raak het product niet aan als het onder stroom staat en er een blootliggende

printplaat of elektrische draad zichtbaar is.

Waarschuwing: raadpleeg de online handleiding voor gedetailleerde

veiligheidsinstructies.

FR: Ne touchez pas le produit lorsqu’il est sous tension et qu’il dispose d’un circuit

imprimé ou d’un l électrique apparent.

Attention : veuillez consulter le manuel en ligne pour des instructions de sécurité

détaillées.

DE: Berühren Sie das Produkt nicht unter Spannung, wenn es eine freiliegende

Leiterplatte oder einen freiliegenden elektrischen Draht hat.

Warnung: Ausführliche Sicherheitshinweise nden Sie im Online-Handbuch.

IT: Non toccare il prodotto quando è sotto tensione se il prodotto ha una scheda di

circuito stampato o un lo elettrico esposto.

Attenzione: consulti il manuale online per le istruzioni di sicurezza dettagliate.

ES: No toque el producto cuando se encuentre bajo tensión si este tiene una placa de

circuito impreso o un cable eléctrico expuesto.

Advertencia: Para instrucciones detalladas de seguridad, consulte el manual en línea.

JP: プリント基板や電線が露出している製品は、電源が入っている状態で直接触

れないでください。

注意：安全性に関わる注意事項の詳細について、オンラインマニュアルを参照

してください。

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference at his own expense.

Industry Canada (IC) Statement

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (A)/NMB-3(A)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation

is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any

interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils

radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit

accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d’en compromettre le fonctionnement.

Use of Trademarks, Registered Trademarks, and other Protected Names and

Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way

to StarTech.com. Where they occur these references are for illustrative purposes

only and do not represent an endorsement of a product or service by StarTech.

com, or an endorsement of the product(s) to which this manual applies by the third-

party company in question. StarTech.com hereby acknowledges that all trademarks,

registered trademarks, service marks, and other protected names and/or symbols

contained in this manual and related documents are the property of their respective

holders.

Warranty Information

This product is backed by a 2-year warranty.

For further information on product warranty terms and conditions, please refer to

www.StarTech.com/warranty.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or

their ocers, directors, employees or agents) for any damages (whether direct or

indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss

of business, or any pecuniary loss, arising out of or related to the use of the product

FR: startech.com/fr

DE: startech.com/de

ES: startech.com/es

NL: startech.com/nl

IT: startech.com/it

StarTech.com Ltd.

45 Artisans Crescent

London, Ontario

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Road

Brackmills,

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

4490 South Hamilton

Road

Groveport, Ohio

43125

U.S.A.

StarTech.com Ltd.

Siriusdreef 17-27

2132 WT Hoofddorp

The Netherlands

Specyfikacje produktu

Marka:	StarTech.com
Kategoria:	Wzmacniacz sygnału WiFi
Model:	C2-ETHERNET-EXTENDER

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z StarTech.com C2-ETHERNET-EXTENDER, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Wzmacniacz sygnału WiFi StarTech.com

StarTech.com C2-ETHERNET-EXTENDER Instrukcja

5 Października 2024

StarTech.com VDSL-LAN-EXTENDER-1G Instrukcja

4 Października 2024

StarTech.com UPOESPLT1G Instrukcja

22 Września 2024

StarTech.com AP300WN2X2W Instrukcja

22 Września 2024

StarTech.com USB110EXT Instrukcja

21 Września 2024

StarTech.com R300WN22MOD5 Instrukcja

21 Września 2024

StarTech.com 10/100 VDSL2 Instrukcja

20 Września 2024

StarTech.com POEEXT2GAT Instrukcja

20 Września 2024

StarTech.com 110VDSLEXT Instrukcja

19 Września 2024

StarTech.com HDBOOST4K Instrukcja

18 Września 2024

Instrukcje Wzmacniacz sygnału WiFi

Najnowsze instrukcje dla Wzmacniacz sygnału WiFi

Hawking Technologies HOW2R1 Instrukcja

14 Października 2024

Planet WNAP-1110 Instrukcja

10 Października 2024

Netgear WN2000RPTv2 Instrukcja

10 Października 2024

Xiaomi RA75 Instrukcja

9 Października 2024

Cudy RE3000 Instrukcja

8 Października 2024

Cudy RE1200 Instrukcja

8 Października 2024

Netgear EX6170 Instrukcja

8 Października 2024

Extron FOX 3G HD-SDI SM Instrukcja

8 Października 2024

Extron FOXBOX Rx VGA MM Instrukcja

8 Października 2024

Extron FOX 3G HD-SDI P SM Instrukcja

8 Października 2024