Instrukcja obsługi SSV Works X3-US10

SSV Works głośnik X3-US10

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SSV Works X3-US10 (5 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/5

X3-US10

2016+ Can-Am Maverick x3

10” Under Seat Enclosure

SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030

www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751

Please read and understand these

instructions completely before

installation to avoid possible injury, or

damage to the accessory or vehicle.

WARRANTY INFORMATION:

All SSV Works enclosures are covered by a limited lifetime warranty against defects

in material or workmanship. All SSV Works Electronics are covered by a limited 1 year

warranty against defects in material or workmanship. All SSV Works Speakers are

covered by a limited 1 year warranty against defects in material or workmanship. Labor

for replacement of defective components is not covered. Contact SSV Works for further

warranty information.

1. X3-US10 Enclosure

2. M6 x 16mm Screws x 10

3. M6 Washers x 10

4. M6 x 25mm Screw x 1

TOOLS NEEDED FOR INSTALLATION PARTS LIST

PARTS LIST IMAGES

5. Large washers x 2

6. D-Brackets x 2

7. A-Bracket x 1

8. B-Bracket x 1

2. M6 x 16mm Screws x 10

7. A-Bracket x 1

11. M6 Locking Hex Nut

8. B-Bracket x 1

12. Foam Strips x 3

3. M6 Washers x 10 4. M6 x 25mm Screw x 1

5. Large washers x 2

9. Seat Risers x 2

1. X3-US10 Enclosure

6. D-Brackets x 2

10. Small Spacer x 1

- 10mm Socket or Wrench

- T-30 Torx Driver

- T-40 Torx Driver

9. Seat Risers x 2

10. Small Spacer x 1

11. M6 Locking Hex Nut

12. Foam Strips x 3

A. Apply the foam strips to the inside right, left and top side of

the enclosure.

C. Remove the factory 10mm nut and bolt from the brake line. Place the washer on top of the factory bracket and push the long M6x25mm screw through

the top. Then attach the brake line, spacer, washer and nut. T hen hand tighten.

B. Using the supplied M6 screws and washers, screw the DD-brackets

to the bottom right and left side of the enclosure.

X3-US10

C C C

SSV HOLE PATTERN

KICKER HOLE PATTERN

FOR UNLOADED ENCLOSURES:

Pink hole pattern: SSV Works Subwoofer

Blue hole pattern: Kicker Subwoofer

If using a different brand subwoofer,

rst see if the subwoofer holes line up

with either one of the pre-drilled hole

patterns. If not, make sure to drill new

holes away from the pre-drilled holes.

Be sure to use the 8 supplied SSV Works

#7 screws when installing your own

subwoofer. #7 Screws x 8

F. Place B-Bracket to the left side of the enclosure and slide the tab underneath the enclosure. (F1) Line up the 2 screw holes and proceed to hand thread

the M6 screws and washers. Use a T30 Torx bit to tighten screws. Repeat for the right side. (F2) Line up the top of bracket A and B with the holes on

the factory seat brakcet. Screw in the M6 screw with the large washer (F3).