Instrukcja obsługi SSV Works GN-F65

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SSV Works GN-F65 (2 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
GN-F65
Polaris General
6.5” Speaker Front Kick Panels
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against
defects in material or workmanship. All SSV Works Electronics are covered by a
limited 1 year warranty against defects in material or workmanship. All SSV Works
Speakers are covered by a limited 1 year warranty against defects in material or
workmanship. Labor for replacement of defective components is not covered.
Contact SSV Works for further warranty information.
TOOLS NEEDED FOR INSTALLATION
PARTS LIST IMAGES
CREASE LINE
CREASE LINE
PASSENGER SID E
CREASE LINE
CREASE LINE
DRIVER SIDE
2. M6 x 1.0 Screws x 6
1. GN-F65 Enclosures
(1 pair)
4. Drll Template
3. M6 Washers x 6
- T-30 Torx Driver - Drill with 1/4” Drill bit - Scribe or Punch tool
A. Cut out the INSIDE template (Driver/Passenger) along the cut
line. Position the template on kick panel above the foot rest
making sure to line up arrows on template to the curves of the
panel as seen on image A.
B. Using a scribing tool, mark the center of the 3 drill points
illustrated on the template as shown on image B.
A B
C. Using a ¼ drill bit, drill holes for mounting of kick Pods .
E. Use the provided M6 screws and washers and loosely tighten
the pod in place through the drilled holes. Once all screws
have been loosely installed, tighten down by hand.
F. Route the speaker wire away from any moving parts and any
sharp metal, then connect to the amplier.
Connecting the GN-F65 using the pre-installed, two-pin
connector will require an optional SSV Works plug-&-play
harness (WP-H1149 - sold separately). If you are not using the
WP-H1149 harness, simply cut off the two-pin connector and
follow the wiring instruction below.
C
E F
D. Place enclosure in location for mounting.
D
GN-F65 © 2017 SSV Works, Oxnard, CA 93030 GN-F65 Rev. A 10-5-17
WIRING INSTRUCTIONS
For proper sound, ensure the speaker polarity is correct
connect the+” to the “+” and the “-“to the “-“from
the speaker wire to the amplier. If using with an SSV
Works complete system refer to the amplier wiring
instructions for more detailed wiring information.
“+”
“+”
-
-

Specyfikacje produktu

Marka: SSV Works
Kategoria: głośnik
Model: GN-F65

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z SSV Works GN-F65, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje głośnik SSV Works

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024