Instrukcja obsługi Speco Technologies SRD80T

Speco Technologies głośnik SRD80T

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Speco Technologies SRD80T (2 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
SRD80T 80W Speaker Horn Driver + Horn Casing SRH20
IMPORTANT NOTES
Before connecting and using this product, please read this instruction manual carefully and keep it on hand for future reference. The manual is to be
considered an integral part of this product and must accompany it if ownership changes, to serve as a reference for correct installation and use as well
as for the safety precautions.
Any incorrect installation or use of this product will void the warranty.
WARNING
Contact your Speco Technologies technical support should any of the following occur:
the Driver Unit does not function (or works in an anomalous way).
the cable has been damaged.
objects or liquids have gotten into the Driver Unit.
the Driver Unit has been damaged due to impact or fire.
SAFETY PRECAUTIONS
1. All precautions, in particular the safety ones, must be read with special attention, as they provide important information.
2. Make sure all connections have been made correctly and the Driver Unit input voltage (in a constant voltage system) or its impedance is suitable for
the amplifier output.
3. Never attempt to carry out any operations, modifications or repairs that are not expressly described in this manual.
4. Driver Unit lines (i.e., speaker wire) can sometimes have sufficiently high voltage (i.e. 100 V) to involve a risk of electrical shock: never install or
connect this Driver Unit when the line is alive.
5. Protect connected speaker wire from damage; make sure it is positioned in a way that it cannot be stepped on or crushed by objects.
6. Should the Driver Unit emit any strange odors or smoke, turn the amplifier off and disconnect the driver from the speaker wire.
7. Make sure that no objects or liquids can get into this product as this may cause a short circuit.
8. To prevent inductive effects from causing hum, noise and poor performance, speaker wire should not be laid together with other electric cables
(mains), microphone cables or line level signal cables connected to amplifier inputs.
9. Strongly recommend this product is only installed by professional qualified installers or specialized firms who can ensure a correct installation and
certify it is installed according to local regulations.
10. WARNING: Do not install the speaker close to the listening area. Exposure to high sound levels can cause permanent hearing loss. The acoustic
pressure level that leads to hearing loss is different from person to person and depends on the duration of exposure. To prevent potentially dangerous
exposure to high levels of acoustic pressure, anyone who is exposed to these levels should use adequate protection devices. When a transducer
capable of producing high sound levels is being used, it is necessary to wear ear plugs or protective earphones.
11. Do not connect this product to any equipment or accessories other than that for which it is intended (i.e., commercial amplifiers).
CAUTION
Install this Driver Unit far from any heat source.
Do not overload this product for extended periods of time.
If the Driver Unit is used in particularly cold places, drive it with a low signal for 5-10 minutes to allow it to warm up before using it maximum power.
Do not use solvents, alcohol, benzene or other volatile substances for cleaning the external parts of this product.
APPLICATION
This unit is intended for use with Speco Technologies SRH20 Horn Casing. When used in conjunction with a casing, driver units can be easily aimed to
any direction. Their use is recommended in houses of worship, supermarkets, public transportation, stadiums, parking lots, factories, warehouses,
schools, offices, etc., or any environments where good sound projection and high efficiency are required.
INSTALLATION
Driver Units are only to be installed by qualified personnel following all safety standards.
Every Driver Unit/Horn Casing must be installed securely, making sure the support structure (walls, ceilings) has the necessary characteristics for the
system weight, to avoid the risk of a fall that could damage things or cause an injury.
Use attachment elements suitable for walls, ceilings (e.g. screw anchors for bricks, screw anchors for concrete, etc.).
CONNECTIONS
Driver Unit connections should only be made by qualified and experienced personnel having the technical know-how or sufficient specific instructions
to ensure that connections are made correctly and to prevent any electrical danger.
To prevent any risk of electric shock, do not connect Driver Units when the amplifier is switched on.
Before turning the system on, check all connections and make sure there are no accidental short circuits.
The entire sound system shall be designed and installed in compliance with the current local laws and regulations regarding electrical systems.
The Driver Unit is designed for connection to audio lines at 70 constant voltage. The connection to the audio line is made using the 2-wire input cable
connected to the back part of the Driver Unit. The adjustment can easily be made on the back of the Driver Unit by changing the point of the tap. The
wires to be used depend on the line voltage and the power to be delivered, as indicated in the table below.
Direct output: V1 (+) V2 (-)
70 constant voltage output
Connection C-5W C-10W C-20W C-40W C-80W
Power 5W 10W 20W 40W 80W
NOTES ABOUT CONSTANT VOLTAGE SYSTEMS
• The Driver Unit input voltage must correspond to the amplifier output voltage. (i.e., 70V)
• The sum of nominal power values of all Driver Units connected to the line must not exceed the amplifier power (minus a 20% safety buffer).
• Make sure all Driver Units are connected in phase (+ to + and - to -) to ensure correct audio reproduction.
• We recommend using 14-2 or 16-2 speaker wire to ensure maximum performance over distance.
• Driver Unit lines must be kept separated from main power cables, microphone cables or others, in order to avoid inductive phenomena that
may cause hum or noises.
• Use cables with twisted wires to reduce hum caused by inductive effects due to coupling with electromagnetic fields.
HOW TO ASSEMBLE THE DRIVER UNIT WITH THE SRH20
The Driver Unit has 1 - 3/8 18 threads (inch screw) which helps to very easily connect it with the matching screw thread on the SRH20.
Speco Technologies is constantly developing and improving products.
We reserve the right to modify product design and specifications without notice and without incurring any obligation.
Speco Technologies . 200 New Highway . Amityville . NY . 11701 . www.specotech.com
Rev. 04/28/20

Specyfikacje produktu

Marka: Speco Technologies
Kategoria: głośnik
Model: SRD80T

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Speco Technologies SRD80T, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Speco Technologies

Speco Technologies

Speco Technologies SPC15R Instrukcja

17 Września 2024
Speco Technologies

Speco Technologies SP-5CLCC Instrukcja

16 Września 2024
Speco Technologies

Speco Technologies SPC40RP Instrukcja

16 Września 2024
Speco Technologies

Speco Technologies SP6MAWT Instrukcja

16 Września 2024
Speco Technologies

Speco Technologies DMS-3TSW Instrukcja

16 Września 2024
Speco Technologies

Speco Technologies SPC10T Instrukcja

15 Września 2024
Speco Technologies

Speco Technologies SP6ECS Instrukcja

15 Września 2024
Speco Technologies

Speco Technologies SPRK65CGT Instrukcja

15 Września 2024
Speco Technologies

Speco Technologies SP525C Instrukcja

15 Września 2024
Speco Technologies

Speco Technologies WB86T Instrukcja

15 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Harman Kardon

Harman Kardon Citation One Instrukcja

14 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024