Instrukcja obsługi Speco Technologies SPCDC6

Speco Technologies głośnik SPCDC6

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Speco Technologies SPCDC6 (2 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Where To Place Your In-Ceiling Speakers

Placement can make all the difference in how your speakers sound, and how easy they will be to

install. Carefully consider where your speakers should be positioned. For optimum performance,

speakers should be mounted to the left and right of the main listening area and a minimum of 8 to

10 feet apart (See Fig. 2). Avoid mounting speakers in stud cavities containing electrical wiring,

heating ducts, water pipes, etc. Make sure the ceiling materials are sturdy enough to support the

weight of the speakers.

Adjustable Tweeters (Fig. 3)

The tweeter in your Speco speaker may be adjusted, allowing you to tailor the speaker to better fit the

listening area. The overall smoothest response is achieved with the tweeter facing straight out; how-

ever, you may find the sound more pleasing by aiming tweeters toward a particular listening area. To

adjust the tweeter, grasp the outside of the tweeter plate and gently pivot it toward the listening area.

Speaker Installation In Existing Construction (See Fig. 4)

Once you have selected the location for your speakers, you are ready to install them.

You will need the following:

• Stud Finder • Drill & Drill Bits • Wire Cutter/ Strippers • Speaker Wire

• Pencil • Phillips Screwdriver • Utility Knife or Drywall Saw • Masking Tape

Speco recommends the use of 16-gauge wire minimum. For wire options, consult your retailer or

custom audio contractor.

1. Speco Speakers are designed to be installed in the ceiling or wall area between studs. Using a stud

finder, make sure you are between two studs. Tape the supplied template to the wall and lightly trace

around the inside with a pencil.

2. Cut the hole using your drywall saw. You may want to start with a small hole in the center of the

outline. This will allow you to check for any obstructions that may exist behind the desired location.

CAUTION: Be certain electrical wiring, water pipes or heating ducts do not interfere in the planned

installation areas prior to drilling or cutting the wall.

3. Run speaker wire from your amplifier or speaker switching device to the speaker location.

4. Carefully remove the grille and inner grille backing by simply pulling it away from the magnetic

baffle. (Note: The open cell

foam inner grille backing

is designed to hide speaker

components from view

and may be removed if

desired.) If you like the

standard white finish of

your Speco speakers grille,

skip to step 5, but if you

want your speakers to

blend in with a colored

wall or ceiling, now is

the time to paint your

Congratulations on choosing Speco

Architectural Loudspeakers. Like all

Speco products, great care has been taken

in their design. Their combination of

advanced engineering and state-of-the-art

materials will provide you with years of

listening pleasure, while blending

smoothly into your home’s decor. Before

you get started, it is a good idea to identify

all the parts and hardware (See Fig. 1).

Speaker with self-contained

mounting clamps

Metal grille with foam

inner grille cover

FIG. 2

Speco ceiling speak can be used as rearers

surround channels by mounting them (1)

on each side of (2) just behind or (3) in, ,

back of the viewing position.

FIG. 3

(Continued on reverse)

Model SPCDC6

61/2˝ Two-Way In-Ceiling Speaker Systems

Cutout template

Pi voting

tweeter

FIG. 1

FIG. 4

speaker’s perforated grille.

(Continued from front)

Remove the foam inner grille backing and put it

aside in a clean and dust free area for later reinstal-

lation if desired. Grille painting hint: Use a paint

roller that is nearly out of paint to first paint the

inside of the grille, then the outside. This will avoid

paint filling the grille perforations.

5. Attach the wire to the input terminals on the

rear of the speaker. Remember to maintain proper

polarity with the amplifier by attaching the posi-

tive (+) lead to the red terminal and the negative

(-) lead to the black terminal.

6. See Fig. 5. With the speaker wire attached to

the speaker, slide the speaker up inside the cut-out

hole. Center the speaker in the cut-out hole and

turn the four locking screws clockwise until the

speaker is drawn up snugly to the wall board from

behind, clamping the speaker in place. Try to tight-

en each screw equally. Replace the speaker grille

by placing it on the frame until the magnets cap-

ture it.

New Construction

1. Determine speaker locations and mark them

on your plans for future reference.

2. If possible, run speaker wires after HVAC

and electrical wiring is in place.

3. Secure speaker wires in place along the run

with insulated staples only and be careful not to

pierce the wire’s insulation. Allow a bit of slack

for expansion of building materials.

4. Needless to say, the actual speakers should

not be installed until the wall boar is in place.d

In the meantime, ve several feet of wirelea

coiled up and secured at the back side of the

mounting hole.

5. To complete the installation follow steps 2

through 5 above.

Operational Check

After making all connections, it’s a good idea to make sure every thing is working properly.

Turn on your surround or stereo system making sure the volume control is turned down and

that the balance control is in the center position. Activate a musical or movie source such as

FM, a CD or DVD player. Gently turn up the volume, you should hear sound coming from

your new Speco speakers. If no sound is heard from any or all speakers, switch off the sys-

tem immediately and check for open or loose connections, wrong polarity or shorts, or

proper source selection.

FIG. 5

Speco Indoor Speakers Lifetime Limited Warranty

This warranty is valid only on products purchased in the United States of America. This warranty

applies only to the original user/purchaser.

Subject to conditions and e lusions found below, this indoor audio speaker is warranted againstxc

manufacturing defects in material and workmanship for the lifetime of the product, including parts

and labor.

Speco Technologies will repair or replace (at our discretion) any parts found to be defective for

the warranty period specified. We will provide a replacement for any defective part.

Conditions

1. You must obtain a Return Authorization (RA) number for any merchandise being returned

to Speco Technologies, whether for return/exchange or repair, whether in or out of warranty.

2. This warranty will be honored only upon the presentation of the original dated bill of sale or

sales slip.

3. Transportation of the product to Speco Technologies for service is the responsibility of the user.

Repaired or replaced product will be returned prepaid during warranty period.

Exclusions

1. This warranty shall not cover improper adjustment of customer operated controls or products

which have been altered or abused.

2. This warranty shall not apply to the appearance of the product or accessory items including,

but not limited to cabinets, cabinet parts, knobs, etc.

3. This warranty does not apply to uncrating, setup, installation, or removal and/or reinstallation

of products prior to or after repair.

4. This warranty shall not apply to repairs or replacements necessitated by any cause beyond the

result of manufacture including, but not limited to, any malfunction, defects or failure caused by

or resulting from unauthorized service or inferior parts, neglect, accident, fire, flood, other acts

of nature or incorrect line voltage.

The foregoing is in lieu of all other expressed warranties and we do not authorize any party to

assume for us any obligation or liability. In no event shall we be liable for incidental or conse-

quential damage arising from the use of this product, or for any delay in the use of this product

due to causes beyond our control.

Some states do not allow limitations of how long an implied warranty lasts and/or do not allow

the exclusion or limitation of consequential damages. The above limitations on implied warranty

and consequential damages may not apply to you.

This warranty gives you specific legal rights. You may have other rights which vary from state

to state.

NOTE: For warranty purposes and your protection in the event

of theft or loss of this product, please fill in the information

below and keep with your sales receipt.

SPCDC6 Specifications

Power Handling: 5 - 65 Watts (100 Watts peak)

Efficiency: 90dB

Frequency Response: 48 Hz-21,000 Hz

Driver Complement: 61

/2˝ (165mm) mica-filled polylaminate cone woofer w/rubber surround

1/2˝ (13mm) pivoting liquid-cooled titanium anodized dome tweeter

Impedance: 8 ohms nominal

Speaker Dimensions: 91/8˝ (232 mm) dia. x 3˝ (76mm) D

Ceiling Cutout Dimensions: 77/8˝ (200 mm) dia.

200 New Highway, Amityville, NY 11701

For information regarding service or return,

Call us TOLL FREE: 1-800-645-5516

In Metro New York 631-957-8700

http://www.specotech.com

Date of Purchase: ____________________________

Where Purchased: ____________________________

Purchase Price: ______________________________

Speco Technologies is constantly developing and improving products. Rev. 4/ /202021

Specyfikacje produktu

Marka:	Speco Technologies
Kategoria:	głośnik
Model:	SPCDC6

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Speco Technologies SPCDC6, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje głośnik Speco Technologies

Speco Technologies SPC15R Instrukcja

17 Września 2024

Speco Technologies SP-5CLCC Instrukcja

16 Września 2024

Speco Technologies SPC40RP Instrukcja

16 Września 2024

Speco Technologies SP6MAWT Instrukcja

16 Września 2024

Speco Technologies DMS-3TSW Instrukcja

16 Września 2024

Speco Technologies SPC10T Instrukcja

15 Września 2024

Speco Technologies SP6ECS Instrukcja

15 Września 2024

Speco Technologies SPRK65CGT Instrukcja

15 Września 2024

Speco Technologies SP525C Instrukcja

15 Września 2024

Speco Technologies WB86T Instrukcja

15 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Bowers & Wilkins LCR3 Instrukcja

15 Stycznia 2025

Hifonics Vulcan VX6.2E Instrukcja

15 Stycznia 2025

Pyle PLRGSW64BK Instrukcja

15 Stycznia 2025

ION Insta Sound Instrukcja

15 Stycznia 2025

Pure Acoustics QBT-340 Instrukcja

15 Stycznia 2025

Yamaha WX-010 Instrukcja

15 Stycznia 2025

Polk REACT SOUND BAR 1 Instrukcja

15 Stycznia 2025

Sennheiser AMBEO Soundbar Plus SB02M Instrukcja

15 Stycznia 2025

Klipsch Reference RB-25 Instrukcja

15 Stycznia 2025

Klipsch Reference RB-35 Instrukcja

15 Stycznia 2025