Instrukcja obsługi Speco Technologies SPCBC6

Speco Technologies głośnik SPCBC6

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Speco Technologies SPCBC6 (2 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Where Place Your In-Ceiling SpeakersTo
Placement can make all the difference in how your speakers sound, and how easy they will be to
install. Carefully consider where your speakers should be positioned. For optimum performance,
speakers should be mounted to the left and right of the main listening area and a minimum of 8 to
10 feet apart (See Fig. 2). Avoid mounting speakers in stud cavities containing electrical wiring,
heating ducts, water pipes, etc. Make sure the ceiling materials are sturdy enough to support the
weight of the speakers.
Adjustable eetersTw (Fig. 3)
The tweeter in your Speco speaker may be adjusted, allowing you to tailor the speaker to better
fit the listening area. The overall smoothest response is achieved with the tweeter facing straight
out; however, you may find the sound more pleasing by aiming tweeters toward a particular listen-
ing area. adjust the tweeter, grasp the outside of the tweeter plate and gently pivot it toward theTo
listening area.
Speaker Installation In Existing Construction (See )Fig. 4
Once you have selected the location for your speakers, you are ready to install them.
You will need the following:
• Stud Finder • Drill & Drill Bits • CutterWire /Strippers • Speaker Wire
• ncil • Phillips Scr • Utility Knife or Drywall Saw • Masking TapePe ewdriver
Speco recommends the use of 16-gauge wire minimum. For wire options, consult your retailer or
custom audio contractor.
1. Speco Speakers are designed to be installed in the ceiling or wall area between studs. Using a stud
finder, make sure you are between two studs. Tape the supplied template to the wall and lightly trace
around the inside with a pencil.
2. Cut the hole using your drywall saw. You may want to start with a small hole in the center of the
outline. This will allow you to check for any obstructions that may exist behind the desired location.
CAUTION: Be certain electrical wiring, water pipes or heating ducts do not interfere in the planned
installation areas prior to drilling or cutting the wall.
3. Run speaker wire from your amplifier or speaker switching device to the speaker location.
4. Carefully remove the grille and inner grille backing.
(Note: The open cell foam
inner grille backing is
designed to hide speaker
components from view
and may be removed if
desired.) If you like the
standard white finish of
your Speco speakers, skip
to step 5, but if you want
your speakers to blend in
with a colored wall or
ceiling, now is the time
to paint your speaker’s
Congratulations on choosing Speco
Architectural Loudspeakers. Like all
Speco products, great care has been taken
in their design. Their combination of
advanced engineering and state-of-the-art
materials will provide you with years of
listening pleasure, while blending
smoothly into your home’s decor. Before
you get started, it is a good idea to identify
all the parts and hardware (See Fig. 1). Speaker with self-contained
mounting clamps
Metal grille with foam
inner grille cover
FIG. 2
Speco ceiling speakers can e used as b rear
surround hannels by mounting them (1)c
on each side of, (2) just behind, or (3) in
back of the viewing position.
1
1
2
2
3
3
FIG. 3
Black
grille
adhesive
(Continued on verse)re
Model S CBC6 P
61/2˝ Two-Way In-Ceiling Speaker Systems
Cutout
template
Painting mask
Pivoting
tweeter
Grille
removal
tool
FIG. 1
FIG. 4
outer frame and perforated grille.
(Continued from front)
(Remove the foam inner grille backing and put it
aside in a clean and dust free area for later rein-
stallation if desired.) The speaker outer surface’s
will accept ordinary latex wall paint or aerosol
spray paint. Because the speaker baffle surface
behind the grille should remain unpainted, you will
need to cover this area with the supplied cardboard
paint mask. Cover the speaker interior black sur’s -
face, woofer and tweeter. Paint the outer speaker
frame and grille separately. (Grille painting hint:
Use a paint roller that is nearly out of paint to first
paint the inside of the grille, then the outside. This
will avoid paint filling the grille perforations.)
5. Attach the wire to the input terminals on the
rear of the speaker. Remember to maintain prop-
er polarity with the amplifier by attaching the
positive (+) lead to the red terminal and the neg-
ative (-) lead to the black terminal.
6. ee Fig. 5. ith the speaker wire attached toS W
the speaker, slide the speaker up inside the cut-
out hole. Center the speaker in the cut-out hole
and turn the four locking screws clockwise until
the speaker is drawn up snugly to the wall board
from behind, clamping the speaker in place. Try to
tighten each screw equally. Replace the speaker
grille by gently pressing it into place. -If neces
sary, use black grille adhesive to secure the grille.
New Construction
1. Determine speaker locations and mark them
on your plans for future reference.
2. If possible, run speaker wires after HVAC
and electrical wiring is in place.
3. Secure speaker wires in place along the run
with insulated staples only and be careful not to
pierce the wire’s insulation. Allow a bit of slack
for expansion of building materials.
4. Needless to say, the actual speakers should
not be installed until the wall board is in place. In
the meantime, leave several feet of wire coiled up
and secured at the back side of the mounting hole.
5. complete the installation follow steps 2To
through above. 5
Operational Check
After making all connections, it’s a good idea to make sure every thing is working properly.
Turn on your surround or stereo system making sure the volume control is turned down and
that the balance control is in the center position. Activate a musical or movie source such as
FM, a CD or DVD player. Gently turn up the volume, you should hear sound coming from
your new Speco speakers. If no sound is heard from any or all speakers, switch off the sys-
tem immediately and check for open or loose connections, wrong polarity or shorts, or
proper source selection.
FIG. 5
Speco Indoor Speakers Lifetime Limited Warranty
This warranty is valid only on products purchased in the United States of America. This
warranty applies only to the original user/purchaser. Subject to conditions and exclusions found
below, this indoor audio speaker is warranted against manufacturing defects in material and
workmanship for the lifetime of the product, including parts and labor. Speco Technologies will
repair or replace (at our discretion) any parts found to be defective for the warranty period
specified. We will provide a replacement for any defective part.
Conditions
1. You must obtain a Return Authorization (RA) number for any merchandise being turnedre
to Speco Technologies, whether for turn/exchange or pai hether in or out of arrantyre re r, w w .
2. This warranty will be honored only upon the presentation of the original dated bill of sale or
sales slip.
3. Transportation of the product to Speco Technologies for service is the responsibility of the user.
Repaired or replaced product will be returned prepaid during warranty period.
Exclusions
1. This warranty shall not cover improper adjustment of customer operated controls or products
which have been altered or abused.
2. This warranty shall not apply to the appearance of the product or accessory items including,
but not limited to cabinets, cabinet parts, knobs, etc.
3. This warranty does not apply to uncrating, setup, installation, or removal and/or reinstallation
of products prior to or after repair.
4. This warranty shall not apply to repairs or replacements necessitated by any cause beyond the
result of manufacture including, but not limited to, any malfunction, defects or failure caused by
or resulting from unauthorized service or inferior parts, neglect, accident, fire, flood, other acts
of nature or incorrect line voltage.
The foregoing is in lieu of all other expressed warranties and we do not authorize any party to
assume for us any obligation or liability. In no event shall we be liable for incidental or conse-
quential damage arising from the use of this product, or for any delay in the use of this product
due to causes beyond our control.
Some states do not allow limitations of how long an implied warranty lasts and/or do not allow
the exclusion or limitation of consequential damages. The above limitations on implied warranty
and consequential damages may not apply to you.
This warranty gives you specific legal rights. You may have other rights which vary from state
to state.
NO : For warranty purposes and your protection in the eventTE
of theft or loss of this product, please fill in the information
below and .keep with your sales receipt
SPCBC6
5 - 60 tts Wa
90dB
63 Hz-21,000 Hz
6
1
/
2
˝ (16 mm) 5 mineral-filled
compression-molded polymer cone
woofer with rubber surround
1
/
2
˝
(1 mm) pivoting liquid-cooled 3
titanium anodized dome tweeter 8
ohms nominal
9˝ (22 mm) 9 dia.x 3˝ (7 mm) D 6
7
1
/
2
˝ (19 mm) 1 dia.
Specifications
Power Handling Efficiency
Fr Reequency sponse Driver
Complement
Impedance
Speaker Dimensions
Ceiling Cutout Dimensions
200 New Highway, Amityville, NY 11701
For information regarding service or return,
Call us TOLL FREE: 1-800-645-5516
In Metro New York 631-957-8700
http://www.specotech.com
Date of Purchase: ____________________________
Where rchased:Pu ____________________________
Purchase Price: ______________________________
Speco Technologies is constantly developing and improving products. Rev. 4/ /202021

Specyfikacje produktu

Marka: Speco Technologies
Kategoria: głośnik
Model: SPCBC6

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Speco Technologies SPCBC6, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Speco Technologies

Speco Technologies

Speco Technologies SPC15R Instrukcja

17 Września 2024
Speco Technologies

Speco Technologies SP-5CLCC Instrukcja

16 Września 2024
Speco Technologies

Speco Technologies SPC40RP Instrukcja

16 Września 2024
Speco Technologies

Speco Technologies SP6MAWT Instrukcja

16 Września 2024
Speco Technologies

Speco Technologies DMS-3TSW Instrukcja

16 Września 2024
Speco Technologies

Speco Technologies SPC10T Instrukcja

15 Września 2024
Speco Technologies

Speco Technologies SP6ECS Instrukcja

15 Września 2024
Speco Technologies

Speco Technologies SPRK65CGT Instrukcja

15 Września 2024
Speco Technologies

Speco Technologies SP525C Instrukcja

15 Września 2024
Speco Technologies

Speco Technologies WB86T Instrukcja

15 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Harman Kardon

Harman Kardon Citation One Instrukcja

14 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024