Instrukcja obsługi SoundTube STNet Switch

SoundTube odbiornik STNet Switch

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SoundTube STNet Switch (8 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
STNET SWITCH | OWNER’S MANUAL
Rev 11.13.2018
STNET SWITCH | OWNER’S MANUAL
Please read the following instructions carefully before installing your SoundTube ® amplier. If you have any questions regarding
installation that are not answered in the following directions, please contact your local sound contractor or the SoundTube ®/
MSE Audio® technical support team. Contact information can be found on the back of the manual.
FCC Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur
de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
Changes or modifcations not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and
receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult
the dealer or an experienced radio/TV technician for help.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un
type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques
de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication
satisfaisante.
MPE Notice
To satisfy FCC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the
antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance
are not recommended.
Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance
de moin de 20 cm. Installer les antennes de facon à ce que le personnel ne puisse approcher à 20 cm ou moins de la
position centrale de l’ antenne. La FCC des États-Unis stipule que cet appareil doit être en tout temps éloigné d’au moins
20 cm des personnes pendant son functionnement.
IC Notice
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
For Module Only
Information for the OEMs and Integrators- This device is intended for OEM integrators only. Please see the full Grant of
Equipment document for restrictions. This device must be operated and used with a locally approved access point.
Label Information to the End User by the OEM or Integrator- If the FCC ID of this module is not visible when it is installed
inside another device, the the outside of the device into which the module is installed must be labeled with “Contains FCC ID:
SU3RM2400A” in a visible area.

Specyfikacje produktu

Marka: SoundTube
Kategoria: odbiornik
Model: STNet Switch

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z SoundTube STNet Switch, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje odbiornik SoundTube

SoundTube

SoundTube STNet Switch Instrukcja

19 Grudnia 2024
SoundTube

SoundTube SA202 Instrukcja

19 Grudnia 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

JBL

JBL Power P-2510 Instrukcja

19 Grudnia 2024
QSC

QSC PL236 Instrukcja

19 Grudnia 2024
QSC

QSC PL218 Instrukcja

19 Grudnia 2024
QSC

QSC PL224 Instrukcja

19 Grudnia 2024
QSC

QSC PL230 Instrukcja

19 Grudnia 2024
QSC

QSC MX1000a Instrukcja

19 Grudnia 2024
QSC

QSC MX2000a Instrukcja

19 Grudnia 2024
QSC

QSC MX3000a Instrukcja

19 Grudnia 2024
QSC

QSC MX1500a Instrukcja

19 Grudnia 2024
QSC

QSC PLX1202 Instrukcja

19 Grudnia 2024