Instrukcja obsługi Sony dcr-ip 220

Sony kamera wideo dcr-ip 220

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Sony dcr-ip 220 (164 stron) w kategorii kamera wideo. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/164
3-078-154-11 (1)
Network Function
Operating Instructions/
Mode d’emploi de la
fonction réseau
© 2002 Sony Corporation
Registration code
2-GB
On trademarks
“Memory Stick” and are registered trademarks of Sony Corporation.
The BLUETOOTH trademarks are owned by their proprietor and used by Sony
Corporation under license.
NetFront by Access Co., Ltd. is adopted for the Internet function of this product.
NetFront is a registered trademark of Access Co., Ltd in Japan.
Copyright © 1996 – 2002 ACCESS CO., LTD.
Portions of the supplied software are based partially on the work of the Independent
JPEG Group.
All other product names mentioned herein may be the trademarks or registered
trademarks of their respective companies. Furthermore, “TM” and “®” are not
mentioned in each case in this manual.
No compensation for your recordings
Any recording contents or downloaded files cannot be compensated for being lost due
to recording/playback malfunction or storage media problems.
Precautions
Before using the network function, make sure to set the clock on the camcorder. For
details, refer to the operating instructions of the camcorder. If you use the network
function without setting the clock, you may not be able to send/receive email or view
a web page.
Do not remove the battery pack or disconnect the AC power adaptor while operating
in NETWORK mode. The setup for the NETWORK mode may be lost. Also, exit the
NETWORK mode when setting the POWER switch to (CHG) OFF or switching the
mode. These are to prevent the NETWORK mode setup from being lost.
It is recommended that you make backup copies of your email messages and your
network preferences. These may be lost from time to time due to memory corruption.
To save the network preferences, write them down on paper, or use “Setup memo,”
described (p. 81). Also, this data may be lost when the camcorder is repaired by
services.
The reset button cannot reset the network preferences.
Note on network operation when using the battery pack
When the remaining battery time is insufficient in NETWORK mode, use the AC power
adaptor or replace the battery pack with a fully charged battery pack. Before connecting
the AC power adaptor or replacing the battery pack, be sure to exit the NETWORK
mode.
Note on the network function
The network function is only available in the following countries or areas:
Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy,
Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and United
Kingdom. (As investigated by Sony Corporation on 1. 4. 2002)
When using the camcorder in a country or area not described above, the network
function is available only in the country or area where you purchased the camcorder.
For customers in CANADA
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
To prevent radio interference to the licensed service, this device is intended to be
operated indoors and away from windows to provide maximum shielding. Equipment
that is installed outdoors is subject to licensing.
3-GB
Introduction
Table of contents
Introduction
The network function on the camcorder...4
Basic operations in the NETWORK mode
..................................................................5
How to use the Network Menu.......... 5
How to use the stylus .......................... 6
How to input characters ...................... 7
Character input screen......................... 9
The available characters list .............. 10
Character input setting ...................... 15
Preparation
Communicating with Bluetooth devices
................................................................16
Before communication....................... 16
Registering a Bluetooth device ......... 17
Using your Modem Adaptor with
Bluetooth Function...................... 17
Selecting other Bluetooth devices
from the list .................................. 23
Deleting a registered Bluetooth
device from the list...................... 23
Setting the Internet connection.................25
Internet service provider ................... 25
Network Setup.................................... 25
Setting other preferences................... 28
Network Operation
Using email..................................................31
Sending email...................................... 31
Using the address book ..................... 42
Receiving email................................... 48
Deleting unnecessary received email
........................................................ 53
Viewing web pages ....................................55
Viewing web pages ............................ 55
How to use the menu bar on the
browser ......................................... 57
Storing the web page into a
“Memory Stick” – Page Memo
........................................................ 63
Shutting down the browser .............. 68
Additional Information
File storage destinations and file names
................................................................69
Troubleshooting..........................................70
Trouble accessing the Internet.......... 70
Trouble with email ............................. 71
Trouble viewing web pages.............. 72
Adjusting the LCD screen
(CALIBRATION)......................... 73
Specifications...............................................74
Messages ......................................................75
General ................................................. 75
Email..................................................... 76
Browser ................................................ 77
Glossary .......................................................78
Setup memo.................................................81
4-GB
Congratulations on your purchase of this Sony Handycam. Your Handycam can access
to the Internet with compatible communicating devices. You can do the following.
– Introduction –
The network function on the camcorder
Sending/receiving email
You can send or receive email anytime, and attach still images and moving pictures to
email messages.
Easy access to the Internet
You can view a web page via the Internet.
Set your camcorder’s clock setting before using the Network functions. (The default
setting is off.) If you do not set the clock setting, you cannot send and receive email or
view web pages.
You also have to set up your camcorder and the peripheral device.
Sending/receiving
email
Easy access to
the Internet
6-GB
How to use the stylus
The buttons required for operating your camcorder are displayed on the LCD screen.
Operate by pressing the buttons on the screen directly but lightly with the stylus
provided. In this manual, pressing the buttons in this way using the stylus is referred to
as “tapping”.
Tap the desired button on the screen with the stylus.
The selected button turns orange.
,
Notes
Use the sytlus supplied to tap the LCD screen.
Do not tap the LCD screen too hard.
Do not make the LCD screen wet.
When the LCD screen gets dirty, use the supplied cleaning cloth.
You cannot drag icons, like on a computer, by touching and sliding across your
camcorder screen with the stylus.
Refer to the operating instructions supplied with your camcorder for the stylus
storage location. To avoid losing the stylus, we recommend that you return it to the
storage location after use.
Basic operations in the NETWORK mode
stylus
7-GB
Introduction
How to input characters
You have to frequently enter characters, such as email addresses, or web pages
addresses (URL), to use the network function. This section describes how to input
characters.
1(1)Open the Network Menu.
For details on how to open the Network Menu, refer to “Accessing the
network” in the operating instructions supplied with your camcorder.
(2)Tap [ Mail].
The Send screen appears.
,
(3)Tap [To].
,
(4)Tap [ New].
The character input screen appears.
,
Basic operations in the NETWORK mode
8-GB
2Selecting the character type
Tap [abcy123], then tap the desired character type.
abc: When inputting alphabetical characters.
123: When inputting numerical characters.
When you selected abc When you selected 123
3Inputting characters
(1)Tap the character you want to input.
,
(2)After you input the characters, tap [Enter].
The Send screen appears again.
,
Basic operations in the NETWORK mode
11-GB
Introduction
To switch between upper and lower case alphabet letters
Tap [a/A] to change the alphabetical keyboard, then enter characters.
To delete a character
Move the cursor with the stylus to the right of the character at which you want to
delete, tap [Back space]. The character at the left of the cursor is deleted.
To add a character
Move the cursor with the stylus to the position at which you want to add a character,
then input characters.
To start a new line
Tap [ ].
When selecting [123]
Symbol characters
(Numerical order)
Basic operations in the NETWORK mode
123+()$C\%
456[]&ˆ|˜
789/{}`”’,
*0#=<>.:;_
12-GB
E.g., Enter “Hello” into the Subject item on the Send screen
1(1)Open the Network Menu.
For details on how to open the Network Menu, refer to Accessing the
network in the operating instructions supplied with your camcorder.
(2)Tap [ Mail].
The Send screen appears.
,
2Entering the subject of a message
(1)Tap [Subject].
(2)Tap [ New].
The character input screen appears.
,
Basic operations in the NETWORK mode
13-GB
Introduction
3(1)Tap [abcy123], then tap [abc].
(2)Tap [a/A] to be able to enter upper-case letters.
,
(3)Tap [H].
H is entered.
,
(4)Tap [a/A] to enter lower-case letters.
,
Basic operations in the NETWORK mode
15-GB
Introduction
Character input setting
Keyboard
You can change the display of the alphabet, PC arrangement keyboard or ABC
arrangement keyboard into a setup you want when you input characters.
1Tap in the character input screen.
,
2Tap the desired setting.
You can set as the following two displays when [abcy123] is set as [abc].
(PC Style is the default setting.)
PC Style (PC arrangement keyboard)
Alphabetical order (ABC arrangement Keyboard)
To switch the setting, tap on the upper-right LCD screen.
Alphabetical orderPC Style
Basic operations in the NETWORK mode
16-GB
Before communication
What is the Bluetooth wireless technology?
The Bluetooth wireless technology allows communication between various Bluetooth
devices without using cables. Devices which can use this technology include PCs,
computer peripheral devices, PDAs, and mobile phones. This omnidirectional
communication system enables communication even if the Bluetooth device is in a bag
or having obstacles between the devices.
Also, the Bluetooth wireless technology has advanced security functions, such as
scrambled frequencies and data encryption.
Authentication
The authentication routine can block unspecified users’ access to this network. When
attempting communication with an unregistered Bluetooth device, the devices must
first be registered with each other by entering a common passkey to each device. When
connecting with a previously registered Bluetooth device, communication starts
without entering the passkey.
Tip on “Passkey”
The passkey is an identification number needed to allow two Bluetooth devices to
communicate with each other. The connection will be permitted after entering the
passkey. This “Passkey” is also referred to as a “Bluetooth passkey”, “PIN”, “Bluetooth
PIN”, etc.
Radio wave indication
indicates the radio wave status of the connected Bluetooth device. (Use this
indication as a guide.)
– Preparation –
Communicating with Bluetooth devices
Preparation
17-GB
Registering a Bluetooth device
To communicate with a Bluetooth device, you need to register it. Here we describe how
to register the Sony Modem Adaptor with Bluetooth Function. Once registration is
complete, you do not have to reregister the Bluetooth device as long as you do not
cancel registration. You can register up to three Bluetooth devices. Also, refer to the
operating instructions supplied with your Bluetooth device.
For more information about Bluetooth devices compatible with your camcorder, access
the following URL:
For customers in Canada
http://www.sony.ca/service/
For customers in the areas other than in Canada
http://www.css.ap.sony.com/
Using your Modem Adaptor with Bluetooth Function
Connecting your camcorder to a Bluetooth device by Bluetooth wireless technology and
communicating.
Notes
When using Sony BTA-NW1/BTA-NW1A Modem Adaptor with Bluetooth Function,
place it at a location that has no obstacles between your camcorder and the device.
The distance between the devices must be within 10 m (33 feet).
The connection may be interrupted depending on the communication conditions.
1Preparing the Modem Adaptor with Bluetooth Function
Set the Modem Adaptor with Bluetooth Function to connection standby (BONDING).
For details, refer to the operating instructions supplied with your Modem Adaptor with
Bluetooth Function.
Communicating with Bluetooth devices
Modem Adaptor with Bluetooth
Function (not supplied)
your camcorder
18-GB
2Specifying your Modem Adaptor with Bluetooth Function as the
connection device
(1)Open the Network Menu.
For details on how to open the Network Menu, refer to “Accessing the
network” in the operating instructions supplied with your camcorder.
(2)Tap [Setup].
The Setup screen appears.
,
(3)Tap [Bluetooth Setup].
The Bluetooth Setup screen appears.
,
Communicating with Bluetooth devices
Preparation
19-GB
(4)Tap [Select].
The Bluetooth devices list appears. When making a registration for the first
time, only [ Return] and [ New] are indicated. The list shows up to three
Bluetooth devices. You can select one of the latest used three Bluetooth devices
from the list.
,
Tip
The last-used Bluetooth device is listed next to [ Return] and [ New].
(5)Tap [ New].
Your camcorder starts searching for your Bluetooth devices. When the
searching is completed, the available Bluetooth devices list appears.
When some Bluetooth devices with the same name appear, display each
Bluetooth device address by tapping [More info.].
,,
Notes
The search takes from about 10 to 60 seconds. The time depends on the number of
Bluetooth devices around your camcorder.
If the Bluetooth device you want to register is not found, carry out the procedure
again from step 4.
(6)Tap the desired Bluetooth device.
The character input screen appears.
,
Communicating with Bluetooth devices
20-GB
(7)Enter the passkey.
For details on how to input characters, see “How to input characters” (p. 7).
For example, when using the BTA-NW1/BTA-NW1A Modem Adaptor with
Bluetooth Function, the passkey is its serial number which is indicated on the
label on the rear panel.
Tip on “Passkey”
The passkey is an identification number needed to allow two Bluetooth
devices to communicate with each other. The connection will be permitted
after entering the passkey. This “Passkey” is also referred to as a “Bluetooth
passkey”, “PIN”, “Bluetooth PIN”, etc. For details, refer to the operating
instructions supplied with your Bluetooth adaptor.
(8)Tap [Enter].
After the registration is completed, the Bluetooth Setup screen appears again.
“Bluetooth Registration Complete” message is displayed.
(9)Tap [OK].
The selected Bluetooth device is specified.
,
Note
When the message “Bluetooth Registration Error Check the Passkey” is
indicated, tap [OK]. Carry out the procedure again from step 4.
Communicating with Bluetooth devices
MODEM ADAPTOR WITH BLUETOOTH
TM
FUNCTION
MODEL NO.
BTA-NW1
®
Passkey
The number used when registering a
Bluetooth device
Preparation
21-GB
(10)Tap [Exit].
The Setup screen appears again. For details on how to turn off the Modem
Adaptor with Bluetooth Function, refer to the operating instructions supplied
with your Modem Adaptor with Bluetooth Function.
(11)Tap [Exit].
The Network Menu appears again.
,
The registration is complete, and your camcorder can communicate with your Bluetooth
device.
Communicating with Bluetooth devices
22-GB
Displaying information on your camcorder
(1)Open the Network Menu.
For details on how to open the Network Menu, refer to “Accessing the
network” in the operating instructions supplied with your camcorder.
(2)Tap [Setup].
The Setup screen appears.
,
(3)Tap [Bluetooth Setup].
The Bluetooth Setup screen appears.
,
Communicating with Bluetooth devices
24-GB
(2)Tap [Setup].
The Setup screen appears.
,
(3)Tap [Bluetooth Setup].
The Bluetooth Setup screen appears.
,
(4)Tap [Select].
The Bluetooth devices list appears.
,
(5)Tap the device you want to delete.
The device name and address of the selected device are indicated.
,
(6)Tap [Delete].
The selected device is deleted from the list.
Communicating with Bluetooth devices
Preparation
27-GB
Password: Enter the password of your user ID for accessing the POP server.
Your user ID and password are required to use email.
Tip
This “Password” is also referred to as a “mail password”, “mail server
password”, etc.
Address: Enter your email address (p. 78).
Tip
This “Address” is also referred to as a “mail address”, “email address”, etc.
POP: Enter the POP (Post Office Protocol) server address of your provider. The
POP server is for receiving email.
Tip
This “POP Server” is also referred to as a “mail server”, “POP3 server”, etc.
SMTP: Enter the SMTP (Simple Mail Transfer Protocol) server address of your
provider. The SMTP server is for sending email.
Tip
This “SMTP Server” is also referred to as a “mail server”, “SMTP mail
server”, etc. The SMTP server may be the same as the POP server,
depending on the provider.
APOP: Select whether you want to use APOP (p. 78).
(7)Select [Browser].
The Browser screen appears.
(8)Set up the following items:
Proxy: Enter the proxy server address of your provider.
Port: Enter the port number of the proxy server of your provider.
Tip
These entries may be unnecessary, depending on your provider. For details,
consult your provider.
(9)Tap [Exit].
The setup is completed, and the Network Setup screen appears again.
(10)Tap [Exit].
The Setup screen appears again.
Setting the Internet connection
28-GB
Setting other preferences
You can access the Internet with your camcorder using the default settings. It is not
necessary to make the following settings. This example is provided to show you how to
make changes, if necessary, in the future.
(1)Display the Setup screen.
(2)Tap [Network Options].
The Network Options screen appears.
,
(3)Set up the following items:
Verify Password: Check this item to delete your password for the PPP screen.
You still have to enter your provider access password each time you
connect, to prevent anyone else from connecting with your ID.
Time Out: Select whether the connection is automatically cancelled if no
communication is made for specific time (1 minute, 2 minutes, 5 minutes, 15
minutes, or 30 minutes).
Note
The telephone line may not be disconnected automatically depending on
web pages. In this case, disconnect the telephone line manually (p. 68).
Setting the Internet connection
Preparation
29-GB
Mail
Send&Receive: Select whether to check the email inbox after sending email.
Save Mail to Server: Select whether to keep copies of the messages on the
server.
Note
If you try to receive email without checking this item, email messages may
not be downloaded and may be lost from your server, depending on the
type of email you receive. For details, see “Note on “Save Mail to Server””
(p. 30).
Signature: Set up this item when you want to attach your signature to
email (p. 40).
Restrict: Select whether to skip an email message if its file size is more than
50 KB, 200 KB, or 500 KB.
Browser
Cookie: Select whether to accept a cookie. When you do not want to send
your personal information, do not check this item. This item is checked at
the default setting.
Image Display: Select whether to display images on the screen when
viewing a web page. This item is checked at the default setting.
Reset: Reset all the items on the Network Options screen except “Signature”
and “Modem Init.”
Note
A verification message does not appear when you try to reset items.
Modem Init: Set up the character string to be used for modem initialization.
If no setup is specified, you do not need to modify this item.
Note
If the setup is wrong, the message “Connection Error No Response From
PPP Server” appears when you try to access the Internet and you will not be
able to access the Internet.
(4)Tap [Exit].
The Setup screen appears again.
Setting the Internet connection
30-GB
Note on “Save Mail to Server”
When “Save Mail to Server” is not checked, copies of email messages received will not
be stored on your server. However, the following error messages described below
depend on the type of email messages. See the table below.
Error messages1) Cause and/or Corrective Actions
Memory Stick Memory Full
Mail Over Size Limit
Attached Invalid File Deleted
Memory Stick Directory Error
1) These error messages are indicated in a message.
2) These email messages are stored on the server even if you did not check the item
“Save Mail to Server”. You can retrieve that email using your computer, etc.
3) The previously downloaded email is not stored on the server if you did not check the
item “Save Mail to Server”. You cannot retrieve this email using your computer, etc.
4) For email messages that have lots of line break, the number of available characters is
less than 4 000.
Setting the Internet connection
You tried to download email when the “Memory Stick” is
already full. 2)
cDelete the email, and delete unnecessary email
messages or image files in the “Memory Stick,” then
download your email again.
cInsert another “Memory Stick” that has sufficient
memory, then download your email again.
You tried to download email whose size is over the size set
in the item “Restrict”. 2)
cYou can download that email using your computer, etc.
cDelete the email, and release the checkmark of the item
“Restrict”, then download that email again.
You downloaded an email message whose the number of
characters of the message is more than 4 000. 3)
cThe camcorder cannot receive an email message that
has 4 000 characters or more. 4)
You downloaded email that has an attached file whose file
name extension is invalid. 3)
cThe camcorder cannot receive files other than those in
the JPEG or MPEG format.
cInsert another “Memory Stick” that has sufficient
memory, then download your email again.
Network Operation
31-GB
This section describes the basic usage of email. Email is sent and received via the
Internet. Email is very convenient; you can send email anytime, and you can also send
images stored in a “Memory Stick” by attaching them to email.
Sending email
By entering the email address of the destination, you can send a message instantly by
email.
1Specifying the destination address
Be careful to enter the address correctly.
Tip
You can select the email address from the address book. For details, see “Selecting the
destination address from the address book” (p. 47).
(1)Open the Network Menu.
For details on how to open the Network Menu, refer to “Accessing the
network” in the operating instructions supplied with your camcorder.
(2)Tap [ Mail].
The Send screen appears.
,
— Network Operation —
Using email
32-GB
(3)Tap [To].
The address list appears. The list shows the latest used six addresses in the
address book. For details on the address book, see “Using the address book”
(p. 42). When you have selected an address listed in the address book, go to
step 7.
,
Tips
The most recently used address is listed under [ Return] and [ New].
Addresses are listed in historical order.
(4)Tap [ New].
The character input screen appears.
,
(5)Enter the email address of an addressee.
For details on how to input characters, see “How to input characters” (p. 7).
(6)Tap [Enter].
The Send screen appears again. The new email address is listed and its check
box is indicated by the checkmark ( ).
,
Tip
You can correct or edit the email address in the address book. For details on
the address book, see “Editing or deleting the address book” (p. 45).
Using email
Network Operation
33-GB
Using email
(7)If you want to send the email message to other addresses, tap other email
addresses.
The check box of the tapped email address is indicated by the checkmark ( ).
(8)Tap [ Return].
The Send screen appears again.
Note
You can register up to 50 addresses in the address book. If you register the 51st address,
the least recently used address is overwritten. The message “Address Book Full
Overwrite the Data with Current Address?” appears for verification. To overwrite it,
tap [OK]. Otherwise, you tap [Cancel] and delete the unnecessary address from the
address book, then enter and register a new address.
34-GB
2Entering the subject of a message
(1)Tap [Subject].
The subject list appears. The list shows the latest used six subjects.
,
When you want to use a subject shown on the list, tap the subject. After
selecting the subject, go to “3 Entering the text of a message” (p. 35).
Tip
The most recently used subject is listed under [ Return] and [ New].
You cannot edit or delete the subject.
(2)Tap [ New].
The character input screen appears.
,
(3)Enter the subject.
For details on how to input characters, see “How to input characters” (p. 7).
Note
The maximum number of characters you can enter is 24.
(4)Tap [Enter].
The Send screen appears again.
,
Using email
Network Operation
35-GB
3Entering the text of a message
Enter the text of the message. You can also select one of your six most recently written
text from the message list, or edit it to suit your purposes.
(1)Tap [Message].
The message list appears.
,
When you select the message you wrote previously, tap the message from the
message list.
When you do not edit message, tap [OK]. After you select the message, go to
4 Sending email” (p. 36).
If you edit the selected text, tap [Edit]. The character input screen appears. Go
to step 3.
(2)Tap [ New].
The character input screen appears.
,
(3)Enter your message.
For details on how to input characters, see “How to input characters” (p. 7).
Note
The maximum number of characters you can enter is 512.
(4)Tap [Enter].
The Send screen appears again.
,
Using email
38-GB
(4)Check or edit the message. When the message is long, tap the message area,
then tap the scroll button V to scroll the message.
When you only check the message:
After checking the message, tap [OK]. The Send screen appears again.
When you edit the message:
Go to step 5.
(5)Tap [Edit].
The character input screen appears.
,
(6)Edit the message.
For details on how to input characters, see “How to input characters” (p. 7).
(7)Tap [Enter].
The Send screen appears again.
,
Using email
Network Operation
39-GB
Attaching images to email
You can send images by attaching them to email messages.
Before operation
Insert the “Memory Stick” that the desired images are stored in into your camcorder.
(1)Follow these procedures: “1 Specifying the destination address” (p. 31),
2 Entering the subject of a message” (p. 34), and “3 Entering the text of a
message” (p. 35).
The Send screen appears.
(2)Tap [Attach].
The images recorded in the “Memory Stick” appear.
,
(3)Tap the desired images to attach.
The selected image is indicated by the checkmark ( ).
To page up or down the index list
Tap [<] or [,]. The next or previous page appears.
To cancel selecting image
Tap the image again. The checkmark will disappear from the image.
To cancel selecting all the images
Tap [ CLR].
Using email
40-GB
(4)Repeat step 3 to select other images to attach.
Notes
The number of images you can attach is up to 99.
The total file size is up to 3MB.
(5)Tap [ OK].
The Send screen appears again. The total number of selected images and the
total file size are indicated.
,
(6)Carry out the procedure described in “4 Sending email” (p. 36) from step 3.
Note
Sending procedure may take long depending on the file size of the image.
Attaching your signature to a message
You can attach your signature to the last column of the email message. You can enter
information such as your name, address and phone number as a signature.
(1)Open the Network Menu.
For details on how to open the Network Menu, refer to “Accessing the
network” in the operating instructions supplied with your camcorder.
Using email
Network Operation
41-GB
(2)Tap [Setup].
The Setup screen appears.
,
(3)Tap [Network Options].
The Network Options screen appears.
,
(4)Tap [Signature].
The character input screen appears.
,
(5)Enter your signature.
For details on how to input characters, see “How to input characters” (p. 7).
Note
The maximum number of characters you can enter is 256.
Using email
42-GB
(6)Tap [Enter].
The setup of your signature is complete, and the Network Options screen
appears again. “Yes” is indicated next to [Signature].
,
(7)Tap [Exit].
The Setup screen appears again.
(8)Tap [Exit].
The Network Menu appears again.
Using the address book
Once you register frequently used email addresses in the address book, you can send
email without entering the email address manually.
Registering destination addresses in the address book
You can register frequently used email addresses in the address book. You can register
up to 50 addresses. Be careful to enter the address correctly.
(1)Open the Network Menu.
For details on how to open the Network Menu, refer to “Accessing the
network” in the operating instructions supplied with your camcorder.
Using email
Network Operation
43-GB
(2)Tap [ Mail].
If the Address screen is not displayed, tap the Address. The Address screen
appears.
,
(3)Tap [New].
The Address Book: New screen appears.
,
(4)Tap [Name].
The character input screen appears.
,
(5)Enter the destination name.
For details on how to input characters, see “How to input characters” (p. 7).
Note
The maximum number of characters you can enter in the [Name] box is 24.
Using email
44-GB
(6)Tap [Enter].
The Address Book: New screen appears again.
,
(7)Tap [Address].
The character input screen appears.
,
(8)Enter the email address.
For details on how to input characters, see “How to input characters” (p. 7).
(9)Tap [Enter].
The Address Book: New screen appears again.
,
(10)Tap [Return].
The Address screen appears again.
,
Using email
Network Operation
45-GB
(11)Tap [Exit].
The Network Menu appears again.
Tips
The addresses are listed in alphabetical order.
When you reply to the address of a previously received email message, the address
will be automatically registered on the address book. To edit the address, see “Editing
or deleting the address book” below.
Editing or deleting the address book
You can edit or delete the names or email addresses in the address book.
(1)Follow steps 1 and 2 in “Registering destination addresses in the address
book” (p. 42).
The Address screen appears.
(2)Display the address you want to edit or delete by tapping or .
(3)Tap [Edit] to select the address.
The Address Book: Edit screen appears.
,
Using email
46-GB
(4)Tap [Name] or [Address].
When editing the registered name, tap [Name], and when editing the
registered address, tap [Address].
The character input screen appears.
,
When you want to delete an address, tap [Delete]. When verification appears,
tap [OK]. When you stop deleting, tap [Cancel].
(5)Edit the name or address.
For details on how to input characters, see “How to input characters” (p. 7).
(6)Tap [Enter].
The Address Book: Edit screen appears again.
,
(7)Tap [Return].
The Address screen appears again.
,
(8)Check the name or address.
(9)Tap [Exit].
The Network menu appears again.
Using email
Network Operation
47-GB
Selecting the destination address from the address book
You can select the destination address from the address book.
(1)Follow steps 1 and 2 in “Registering destination addresses in the address
book” (p. 42).
The Address screen appears.
(2)Select the address you want to send email by tapping or .
(3)Tap [tTo].
The Send screen appears. The selected address is set as the destination address.
,
(4)Carry out the procedures described in “2 Entering the subject of a message”
(p. 34).
Using email
48-GB
Receiving email
Once you receive email, you can reply to it or forward it.
Before operation
Release the lock of the “Memory Stick”.
Insert a “Memory Stick” into your camcorder, for storing email.
Checking your email inbox
Tip
You can leave a copy of your in-coming messages on the mail server even if you
download the message using your camcorder. For details, see “Setting other
preferences” (p. 28).
(1)Open the Network Menu.
For details on how to open the Network Menu, refer to “Accessing the
network” in the operating instructions supplied with your camcorder.
(2)Tap [ Mail].
If the Receive screen is not displayed, select the Recieve from the Send, Receive
and Address. The Receive screen appears.
,
(3)Set your Bluetooth device to connection standby with your camcorder.
For details, refer to the operating instructions supplied with your Bluetooth
device.
Using email
Network Operation
49-GB
(4)Tap [Receive].
The screen for verifying the connection appears.
,
(5)Check the telephone number of the access point.
When dialing other telephone numbers
Tap [TEL No.]. The list of the registered telephone number(s) appears. Tap the
desired telephone number to select it.
To connect to an outside line, for example in a hotel, check the item “Prefix
No.” and enter the prefix number.
(6)Tap [Connect].
Your camcorder starts dialing the selected telephone number. When an email
message has been sent to you, your camcorder downloads it, and the message
“Receiving Mail Complete” appears. Tap [OK]. The phone line is automatically
disconnected after email is received.
,
(7)When an email message has been received, tap the area where a message is
displayed or [Message].
The message is displayed.
,
(8)Tap [Return].
The Receive screen appears again.
Using email
50-GB
Using email
To cancel receiving email
Tap [Cancel] while downloading. Email you did not download remains on the mail
server.
When the message is long
Tap the scroll button V to scroll the message.
When a file is attached to an email message
Your camcorder can receive the following extension file: .jpg, .mpg, .jpeg, and .mpeg.
When you receive files other than these files, the message “Attached Invalid File
Deleted” is inserted in the email message. Your camcorder cannot play back the
attached image if the file is in an incompatible format.
To view an attached file
Exit the NETWORK mode, then view the image following the same procedure as that
for viewing an image recorded in a “Memory Stick.” In such cases, the attached file will
be stored next to the last-recorded image recorded in VCR or MEMORY/NETWORK
mode.
When no new messages have been sent to you
The message “No New Mail” appears.
URL included in an email message
When a URL (“http://...”) is typed in the message, tap the URL. The browser starts
automatically and accesses the indicated web page.
Notes
The number of email message characters allowed to enter is up to 4 000. If you enter
more than 4 000 characters, the excess characters will be deleted and a message that
tells you so appears in the beginning of the text.
Receiving procedure may take long depending on the file size of the attached image.
Tips
You can set to check the email inbox automatically after sending email. For details, see
“Setting other preferences” (p. 28).
You can skip an email message if its file size is too large. For details, see “Setting other
preferences” (p. 28).
For email messages, the number of characters for the subject and for the sender name
are up to 24, respectively. When you receive an email message with more than 24
characters in these items, you cannot read the subject and the sender name on your
camcorder.
Network Operation
51-GB
Sending your answer – Reply
You can reply to an email message promptly without entering the address.
(1)Display the Receive screen.
(2)Tap the area where a message is displayed or tap [Message].
The selected message is displayed.
,
(3)Tap [Reply].
The Send screen appears.
,
Tip
“Re:” is added to the beginning of the subject line.
(4)Carry out the procedure described in “3 Entering the text of a message”
(p. 35) to enter the text of the message.
Tip
You cannot quote a received email message.
(5)Carry out the procedure from step 3 described in “4 Sending email” (p. 36).
Using email
52-GB
Forwarding the message to another person – Forward
You can forward a received message to others.
(1)Display the Receive screen.
(2)Display email that you want to forward the message by tapping or .
(3)Tap the area where a message is displayed or tap [Message].
The selected message is displayed.
,
(4)Tap [Forward].
The Send screen appears.
,
Note
An attached file is not automatically forwarded. When you want to send the
attached file, see “Attaching images to email” (p. 39).
Tip
“Fw:” is added to the top of the subject line.
(5)Carry out the procedure from step 3 described in “1 Specifying the
destination address” (p. 32) or “Selecting the destination address from the
address book” (p. 47) to specify the destination address.
Using email
Network Operation
53-GB
(6)Carry out the procedure described in “3 Entering the text of a message”
(p. 35) to modify the message.
Tip
The number of characters you can enter for a message is up to 512. The excess
characters will be deleted.
(7)Carry out the procedure described in “4 Sending email” (p. 36) from step 3.
Deleting unnecessary received email
You can receive and store up to 50 email messages in a “Memory Stick”. The 51st email
message may not be received and an error message appears.
Before operation
Release the lock of the “Memory Stick”.
Insert the “Memory Stick” that the email message you want to delete is stored in into
your camcorder.
(1)Open the Network Menu.
For details on how to open the Network Menu, refer to “Accessing the
network” in the operating instructions supplied with your camcorder.
(2)Tap [ Mail].
Select the Receive from the Send, Receive and Address. The Receive screen
appears.
,
Using email
Network Operation
55-GB
A site that posts information on the Internet is called “web page” or “web site”. You can
easily retrieve information by accessing a web site on the Internet.
Viewing web pages
1Entering the URL needed to access the web page
Enter the address of the web page, and then access the Internet. Be careful to enter the
address correctly.
Tip on URL
A web site has a unique address on the Internet. The address is called a URL. This URL
is required to access a web site.
(1)Open the Network Menu.
For details on how to open the Network Menu, refer to “Accessing the
network” in the operating instructions supplied with your camcorder.
(2)Tap [ Browser].
The following screen appears.
,
(3)Tap (New URL).
The character input screen appears.
,
Viewing web pages
56-GB
(4)Enter the URL.
For details on how to input characters, see “How to input characters” (p. 7).
(5)Set your Bluetooth device to connection standby with your camcorder.
For details, refer to the operating instructions supplied with your Bluetooth
device.
(6)Tap [Enter].
The screen used for verifying the connection appears.
,
(7)Check the telephone number of the access point.
When dialing other telephone numbers
Tap [TEL No.]. The registered telephone number list appears. Tap the desired
telephone number to select it.
To connect to an outside line, for example in a hotel, check the item “Prefix
No.” and enter the prefix number.
(8)Tap [Connect].
Your camcorder starts dialing the selected telephone number. After the
connection is completed, the web page selected in step 4 is loaded.
,
(9)Operate the browser using the menu bar.
For details on the menu bar, see “How to use the menu bar on the browser”
(p. 57).
Viewing web pages
Network Operation
57-GB
Viewing web pages
How to use the menu bar on the browser
When you access the Internet and view a web page, you can carry out various
operations using the menu bar. While the browser screen is displayed, tap
menu
on the
upper-right LCD screen to display the menu bar.
To show the menu bar
Tap
menu
on the upper-right LCD screen.
The following menu bar appears.
To hide the menu bar
Tap
menu
or in the menu bar. The menu bar disappears.
The buttons on the menu bar
Button Function
(Previous Page) Go to the previous page in your step.
(Next Page) Go to the next page in your step.
(Refresh) Refresh the current page.
Use this button when images or characters on the web
page are not displayed properly.
(Stop) Stop loading the current page.
(Zoom) Change the page size.
?
(Help) Display the introduction of each button.
(Bookmark) Bookmark the current page. (Bookmarks are stored in the
camcorder.) Bookmarking is convenient to access
frequently-visited pages.
(New URL) Enter the URL of a web page.
(Page Memo) Store the current page in the “Memory Stick.” You can
then view the page without accessing the Internet.
(Page Information) Show the title and URL of the current page.
(Line Close) Disconnect the phone line.
Hide the menu bar.
END
(END) Exit the browser.
58-GB
When you fail to load a web page
[Loading Error] message appears. Tap [OK], then tap
menu
on the upper-right LCD
screen, and tap
END
in the menu bar. Network menu appears again.
Note
The buttons may not function, depending on the accessed web page.
Note on connection status indication
The connection status is indicated on the top of the screen. This item also shows a
connected time and the address of the web page. The connecting time indication should
be used as a guide.
Off Line: being offline
Loading: Loading a web page
On Line: being online
Notes
When the address is too long to display, the whole address is not indicated. If you
want to know the correct address of the page, tap . The address is indicated in full.
A portion of the whole page is displayed on the screen.
It takes more time to load a large size page, and its images or text may not be
displayed properly. This is not a malfunction.
When you try to open a large size page, the message “Data too Large for Full Display”
appears and the entire page may not be loaded.
When viewing a scaled-down page, the screen may show some flicker or the color
may be strange. This is not a malfunction.
To prevent a malfunction, operate the menu bar buttons after loading the page.
Tip
You can access the web page from a bookmark. For details, see “3 Jumping to the web
page specified by the bookmark” (p. 62).
Viewing web pages
Network Operation
59-GB
Viewing web pages
2Bookmarking the web page – Bookmark
You can bookmark web pages you frequently access. You can bookmark up to 30
bookmarks.
(1)Display the web page you want to bookmark.
(2)When the menu bar is not displayed, tap
menu
on the upper-right LCD screen.
The menu bar appears.
(3)Tap (Bookmark).
The bookmark list appears.
,
(4)Tap [ Add].
The bookmark is added, and the display returns to the web page.
Notes
The phone line may not be disconnected automatically. If this happen, disconnect the
phone line manually (p. 68).
You cannot bookmark a web page that the URL is more than 256 characters.
60-GB
Viewing web pages
To edit a bookmark
You can edit the title of a bookmark.
(1)Tap (Bookmark).
The bookmark list appears.
,
(2)Tap the bookmark you want to edit.
The title and URL are indicated.
,
(3)Tap [Edit].
The character input screen appears.
,
(4)Edit the name.
For details on how to input characters, see “How to input characters” (p. 7).
(5)Tap [Enter].
The title of the bookmark is modified.
,
(6)Tap [ Return].
The Browser screen appears again.
64-GB
(3)Tap (Page Memo).
The page memo list appears.
,
(4)Tap [ Add].
The message “Saving Page Memo Do Not Remove Memory Stick” appears.
After the message disappears, storing is complete.
,
(5)Browser screen appears again.
To cancel storing the web page
During storing, tap [Cancel].
Note
You cannot store the web page while loading it.
Editing the title of a page memo
You can edit the title of a page memo stored in a “Memory Stick.”
Before operation
Release the lock of the “Memory Stick”.
Insert a “Memory Stick” that the page memo you want to edit is stored in into your
camcorder.
(1)When the menu bar is not displayed, tap
menu
on the upper-right LCD screen.
The menu bar appears.
Viewing web pages
66-GB
(7)Tap [ Return].
The browser screen appears again.
To delete the page memo
You can delete page memos. We recommend that you delete unnecessary page memos
since you can only store up to 30 page memos.
Before operation
Release the lock of the “Memory Stick”.
Insert a “Memory Stick” that the page memo you want to delete is stored in into your
camcorder.
(1)When the menu bar is not displayed, tap
menu
on the upper-right LCD screen.
The menu bar appears.
(2)Tap .
The page memo list appears.
,
(3)Tap the page memo you want to delete.
The following screen appears.
,
Viewing web pages
Network Operation
67-GB
(4)Tap [Delete].
The message “Delete This Page Memo Item?” used for verification appears.
,
(5)Tap [OK].
The selected page memo is deleted and the page memo list appears again.
(6)Tap [ Return].
The browser screen appears again.
To cancel deleting the page memo
Tap [Cancel] in step 5.
Displaying a web page stored in page memo
You can display a page memo stored in a “Memory Stick.”
Before operation
Insert the “Memory Stick” that the page memo you want to display is stored in into
your camcorder.
(1)When the menu bar is not displayed, tap
menu
on the upper-right LCD screen.
The menu bar appears.
(2)Tap .
The page memo list appears.
,
Viewing web pages
68-GB
(3)Tap the page memo you want to display.
,
(4)Tap [Open].
The web page stored in page memo is displayed.
To select other page memo
Tap [Return] in step 3. The page memo list appears. Tap other page memo.
Shutting down the browser
To finish viewing the web page, and to disconnect the phone line
(1)Tap
menu
on the upper-right LCD screen to display the menu bar.
(2)Tap
END
.
The browser is closed, then the phone line is disconnected.
To only disconnect the line
Tap . The phone line is disconnected.
Note
When shutting down the browser, a verification message may appear, depending on
your camcorder.
Viewing web pages
Additional Information
69-GB
Files are grouped in the following folders. You can only view these folders on a
computer. The meanings of the file names are as follows.
sssss stands for any number within the range from 00001 to 99999.
ssss stands for any number within the range from 0001 to 9999.
aaa stands for a portion of an attached file name.
Folder File name Meaning
100MSDCF DSCsssss.JPG Still image file
MOVsssss.MPG Moving image file
700MSNET aaasssss.JPG Still image file over the network
aaasssss.MPG Moving image file over the network
CAMNET01 RCV.MBX Incoming email list*
IMAGEMEM.CNF Page memo management file*
MEMOssss MEMOssss.HTM Page memo HTML file
IMGssss.JPG Page memo still image file
IMGssss.GIF Page memo image file
IMGssss.PNG Page memo image file
IMGssss.XBM Page memo image file
* Do not delete these files. These are required files even though they cannot be verified
using a computer.
– Additional Information –
File storage destinations and file names
Folder containing still image files and
MPEG MOVIE AD moving image files
Folder containing files of page memo
(2), etc.
Folder containing files of page memo
(1), etc.
Folder containing the text data of email,
etc.
Folder containing image files attached
to email
70-GB
Troubleshooting
Trouble accessing the Internet
The message “...Incomplete” or “Authentication Error...” is indicated and your camcorder
cannot access the Internet.
cCheck your setup according to the procedure described in “Network Setup” (p. 25).
The camcorder cannot access the Internet.
cTry to access it again after a while.
The message “Line is Busy or Phone number may be Wrong” is indicated and your
camcorder cannot access the Internet.
cThe phone line of your provider is busy. Call again after a while.
cThe settings for the telephone number may be incorrect. Please check those settings.
cThe telephone signaling type setup of the Modem Adaptor with Bluetooth function
may be wrong. Check the setup.
The message “Bluetooth Connection Error” is indicated and your camcorder cannot access
the Internet.
cCheck that your Bluetooth device is turned on.
cInstall your Bluetooth device nearer to your camcorder.
The message “Phone Line Disconnected” is indicated when making an entry in the online
registration procedure.
cData entry can be done offline. When your camcorder needs to connect with the site,
the screen for verifying the connection appears. Tap [Connect], then the connection
will be established again.
The message “Bluetooth Authentication Error Check the Certified Status” is indicated and
your camcorder cannot access the Internet.
cYour Bluetooth device may be deleted from the registration. Set it up again.
The message “Bluetooth Connection Error Select Bluetooth Device” is indicated and your
camcorder cannot access the Internet.
cCheck your setup according to the procedure described in “Registering a Bluetooth
device” (p. 17).
The message “Low Battery” is indicated and your camcorder cannot access the Internet.
cCharge the battery pack or use the AC power adaptor, then connect again.
Additional Information
71-GB
Troubleshooting
Trouble with email
The message “DNS Error The Requested URL Could Not Found” is indicated and your
camcorder cannot send or receive email.
cThe DNS setup may be wrong. Check the PPP setup.
Your camcorder cannot send email.
cThe clock setting of your camcorder is not set. Set up the clock setting.
cCheck your setup according to the procedure described in “Network Setup” (p. 25).
cConnect again after a while.
Your camcorder cannot receive email.
cThe clock of your camcorder is not set up. Set it up.
cCheck your setup according to the procedure described in “Network Setup” (p. 25).
cAll of your downloaded email messages are stored in the “Memory Stick.” Insert a
new “Memory Stick” that has sufficient memory and download your email again.
Also, check that the lock switch is set to release.
cYou can restrict the file size of downloaded email messages. Check the setup of the
item “Restrict” on the Network Options screen.
cYou can store up to 50 downloaded email messages in a “Memory Stick.” If you want
to store a 51st email message, delete unnecessary email or insert a new “Memory
Stick” that has sufficient memory and then download your email again.
All of the email message cannot be received.
cThe maximum size of an email is 4 000 characters. You cannot receive the entire text of
email that has more than 4 000 characters.
The message “PPP Authentication Error” is indicated.
cCheck your setup according to the procedure described in “Network Setup” (p. 25).
You received an email message sent from Mailer Daemon.
cYour email has not been sent to its destination address. Check the email address. If
you receive an email message from Mailer Daemon and the destination address is
correct, the server may be down, or the email address may have changed.
Attached files are not saved in the “Memory Stick.”
cThe compatible file types are .jpg, .mpg, .jpeg, and .mpeg only. Check the file type.
cThe message “Memory Stick Directory Error” may be indicated when a “Memory
Stick” whose directory structure does not correspond to the DCF standard is inserted.
cAll of your downloaded email messages are stored in the “Memory Stick.” Insert a
new “Memory Stick” that has sufficient memory and download your email again.
Also, check that the lock switch is set to release.
cYou can restrict the file size of downloaded email messages. Check the setup of the
item “Restrict” on the Network Options screen.
72-GB
Troubleshooting
Trouble viewing web pages
The images are not displayed.
cCheck the setup of the item “Image Display” on the Network Options screen.
Some of the web page or all of the web page is not displayed.
cWhen the page has been made using the software, such as Macromedia Flash, the
page does not correspond to the browser of your camcorder.
cThe web page may be using Java Script and Java Applets that cannot be excuted with
incompatible commands.
It takes some time to load the web page.
cWhen the web page is busy, try to connect through other providers or other access
points, or connect during off-peak times.
The web page is not loaded.
cWhen entering its URL
Check that the address is correct. (For example, did you enter “0” or “O”, “-” or “_”)
cWhen accessing through the bookmark or page memo
The address may have been changed or the link structure of the web site may have
been modified. When the link structure is modified, follow the address to its source.
(For example, when you cannot access “http://www.sony.co.jp/xxxx/”, then try to
access “http://www.sony.co.jp/”)
The web page cannot be displayed.
cThe item “Cookie” may not be checked. Check the item “Cookie” on the Network
Options screen.
The cookie is not saved.
cExit the NETWORK mode, the cookie will be deleted.
The message “DNS Error The Requested URL Could Not Found” is indicated and the web
page is not displayed.
cThe setup of the item “DNS” may be wrong. Check the setup of the PPP screen.
cThe setup of the item “Proxy” may be wrong. Check the setup of the Browser screen.
Additional Information
73-GB
Troubleshooting
Adjusting the LCD screen (CALIBRATION)
The buttons on the touch panel may not work correctly. If this happens, follow the
procedure below.
(1)Set the POWER switch to (CHG) OFF.
(2)Eject the tape from your camcorder, then disconnect any connecting cable from
your camcorder.
(3)Close the LCD panel with the LCD screen facing out.
(4)Set the POWER switch to VCR while pressing DISPLAY/TOUCH PANEL,
then keep pressing DISPLAY/TOUCH PANEL for about five seconds.
(5)Follow the procedure below with your finger or the supplied stylus.
1Touch at the upper left corner.
2Touch at the lower right corner.
3Touch in the middle of the LCD screen.
If you do not press the right spot, always returns to the position at the upper
left corner.
Note
You can only carry out this operation with the LCD screen in the step 3 position.
For details on adjusting the LCD screen (CALIBRATION), refer to the Operating
Instructions with your comcorder.
CALIBRATE CALIBRATE CALIBRATE
DISPLAY/TOUCH PANEL
74-GB
Specifications
Bluetooth
The number of registered
devices available
3
Email
Sending
The maximum number of
email destination addresses to
which a message can be sent
at one time
50
The registrable number of
subjects
6
The maximum number of
characters of a subject
24
The registrable number of
messages
6
The maximum number of
characters of a message
512
The maximum number of
images attached to email
99
The maximum file size of
images attached to email
3MB
Signature
The number of characters
256
Address book
The registrable number of
destination addresses
50
The maximum number of
characters of a name
24
The maximum number of
characters of an email address
64
Receiving
Compatible attachment file
standards
Extension: .jpg, .mpg, .jpeg,
.mpeg
The maximum number of
characters of an email
message
Approx. 4 000
The maximum number of
email messages recordable in
a “Memory Stick”
50
Browser
The number of bookmarks
available
30
The maximum number of
characters of a bookmark title
27
The maximum number of page
memos recordable in a
“Memory Stick”
30
The maximum number of
characters of a page memo title
27
The maximum number of
characters of URL
255
Additional Information
77-GB
Browser
Message Cause and/or Corrective Actions
You are About to View
Pages Over a Secure Connection
Do You Want to Continue?
You are About to Leave
a Secure Internet Connection
Do You Want to Continue?
Warrant Date Expired
Invalid Data
Open Anyway?
Set the Date and Time
Invalid Data
Open Anyway?
Page Certification Error
Invalid Data
Open Anyway?
Opening Error
Invalid File Type
DNS Error
The Requested URL
Could Not Found
Loading Error
Read-Only File in Directory
Unable to Delete the File
Check the File Status
Opening File Error
Read-Only File
This File is Locked
Enter User Name
and Password
Timeout
Disconnected Automatically
Loading...
Retry Later
Messages
You tried to open an SSL (p. 79) page. When you know that the page
is safe, tap [OK].
You tried to open a page which is not SSL protected. When you know
that the page is safe, tap [OK].
The warrant of the page is no longer valid. When you know that the
page is safe, tap [OK].
The clock is not set up on your camcorder. Set up the clock setting.
The certification of the page may be broken, wrong, or it may be of
other pages. When you know that the page is safe, tap [OK].
You cannot display this page on your camcorder.
The URL may be wrong.
The DNS entry on the PPP screen during manual setup may be
wrong. Check this item.
Connect to the page again after a while.
Tap
menu
on the upper-right LCD screen, then tap
END
.
Files modified with a computer may not be deleted by your
camcorder.
User authentication is required to access the page. Enter your user
name and password.
Check the Network Options setup (p.
28
).
The page memo cannot be stored while the unit is loading a web
page. Store it again after the web page has been loaded (p. 63).
78-GB
Glossary
Access point (p. 26)
A telephone number used to access the Internet, which is provided by an Internet
service provider. Most providers install access points in various areas. We recommend
that you select the most convenient access point which allows you to obtain the lowest
telephone charges.
Address book (p. 42)
Used to register email destination addresses.
APOP (p. 27)
An abbreviation for Authenticated Post Office Protocol. APOP is an authentication
protcol for security. For more information on whether the provider support APOP or
not, consult your provider.
@ (At mark)
Used to separate the domain name and the user name.
Attachment (p. 39)
To attach a file to an email message.
Bookmarks (p. 59)
Rigister your favorite or most frequently visited Internet web pages. Once you register a
web page, you can visit it without entering its URL.
Connect time (p. 58)
The time for being connected with an Internet service provider using a dial-up
connection. Most Internet service providers charge for the time connected.
Cookie (p. 29)
Used by the operator of an Internet site to identify the user. This is frequently used in
online shopping.
Dial-up connection
The dial-up connection is used to access the Internet using a phone line.
DNS (p. 26)
An abbreviation for Domain Name System. This “DNS” is also referred to as a “name
server”, “primary DNS server”, “primary name server”, etc. This is a server that
replaces a domain name with an IP address. This is specified by an IP address.
Download
Load information from the server through the phone line.
Email (p. 31)
Using a network, such as the Internet, you can send and receive a message very quickly.
Email is easy to edit or store.
Email address (p. 27)
This is the destination address for email. There is no need to specify the country and the
house number. The same address does not exist in the world. You can receive your
email even if your are in another country.
Forward (p. 52)
To forward a received email message to another person. “Fw:” (Forward) is added to
the beginning of the title in order to indicate that the email is a forwarded email.
Additional Information
79-GB
Glossary
ID (p. 26)
Used to identify the user in combination with a password when accessing the Internet
through the Internet service provider.
Internet (p. 25)
A worldwide network of computers. You can use email, information retrieval services,
etc., over this network.
Internet service provider (p. 25)
Also referred to as a “Provider,” an “ISP,” etc. A company that provides access to the
Internet.
Link
A related page address listed on a web page as a web link.
Login
Connect to a specific service by entering an ID and password.
Passkey (p. 16)
The passkey is an identification number needed to allow two Bluetooth devices to
communicate with each other. This “Passkey” is also referred to as a “Bluetooth
passkey”, “PIN”, “Bluetooth PIN”, etc.
Password
Used to access the provider in combination with a user ID.
POP3 (p. 27)
An abbreviation for Post Office Protocol, Version 3. This is a server used to receive
email.
PPP (p. 25)
An abbreviation for Point to Point Protocol, Version 3. This is a protocol for accessing a
provider using a dial-up connection.
Proxy (p. 27)
A server or programme to make a computer located inside a firewall pass through the
firewall.
Reply (p. 51)
To reply to a previously received email message. When replying, “Re:” (Reply) is added
to the beginning of the title in order to indicate that the email is a reply.
Signature (p. 40)
Used to add your name, your address, etc., to the end of a message.
SMTP (p. 27)
An abbreviation for Simple Mail Transfer Protocol. This is a server used to send email.
SSL (p. 77)
An abbreviation for Secure Sockets Layer. A protocol for exchanging information safely
between web browsers and web servers. SSL is frequently used for credit card
transactions over the Internet. SSL also has a function to verify ownership and to
encrypt data.
Additional Information
81-GB
Be careful not to reveal these entries.
Network Menu
Network Setup
Provider Setup
PPP ID
Password
DNS1
DNS2
TEL No. 1
TEL No. 2
TEL No. 3
Mail User ID
Password
Address
POP Server
SMTP Server
Browser
Proxy
Port
Setup memo
Example
abc123@xxx.so-net.com
hcHZ7yd
192.168.0.1
192.168.0.2
XXXXXXX
abc123
hcHZ7yd
abc123@xxx.so-net.com
pop.xxx.so-net.com
smtp.xxx.so-net.com
proxy.xxx.so-net.com
8080
2-FR
A propos des marques commerciales
“Memory Stick” et sont des marques déposées de Sony Corporation.
Les marques commerciales BLUETOOTH appartiennent à leur propriétaire et sont
utilisées sous licence par Sony Corporation.
NetFront de Access Co., Ltd. est adopté pour la fonction Internet de ce produit.
NetFront est une marque déposée de Access Co., Ltd au Japon.
Copyright © 1996-2002 ACCESS CO., LTD.
Certaines parties du logiciel fourni se réfèrent partiellement à l’œuvre de Independant
JPEG Group.
Tous les autres noms de produits mentionnés ici sont soit des marques commerciales
soit des marques déposées de leurs sociétés respectives. Par ailleurs, “TM” et “®” ne
sont pas systématiquement mentionnés dans ce manuel.
Aucun dédommagement pour les enregistrements
Vous ne pouvez prétendre à aucun dédommagement si l’enregistrement ou la lecture
de fichiers téléchargés n’a pas eu lieu en raison d’un problème d’enregistrement, de
lecture ou du support de stockage.
Précautions
Avant d’utiliser la fonction réseau, veillez à régler l’horloge du caméscope. Pour le
détail, reportez-vous au mode d’emploi du caméscope. Si vous utilisez la fonction
réseau sans régler l’horloge, vous ne pourrez peut-être pas envoyer et recevoir de
courrier, ni afficher de page web.
Ne retirez pas la batterie ou ne débranchez pas l’adaptateur secteur en mode
NETWORK. Les réglages du mode NETWORK risquent d’être perdus. Sortez aussi du
mode NETWORK avant de régler le commutateur POWER sur (CHG) OFF ou de
changer de mode.
Il est conseillé d’effectuer des copies des messages email et des préférences réseau. Ces
éléments risquent d’être perdus en cas d’altération de la mémoire. Sauvegardez les
préférences réseau en en gardant une trace écrite ou en utilisant “Configuration de la
mémoire” (p. 81). Ces données peuvent être perdues en cas de réparation.
La touche de réinitialisation ne peut pas réinitialiser les préférences réseau.
Remarque sur la fonction réseau en cas d’utilisation de la batterie
Si l’autonomie de la batterie est insuffisante en mode NETWORK, utilisez l’adaptateur
secteur ou remplacez la batterie par une pleine. Avant de raccorder l’adaptateur secteur
ou de remplacer la batterie, vous devez sortir du mode NETWORK.
Remarque sur la fonction réseau
La fonction réseau n’est disponible que dans les pays suivants : Allemagne, Autriche,
Belgique, Danemark, Espagne, Finlande, France, Grèce, Irlande, Italie, Luxembourg,
Norvège, Pays-Bas, Portugal, Royaume-Uni, Suède et Suisse. (à la connaissance de Sony
au 1er avril 2002)
Si vous utilisez le caméscope dans un autre pays ou une autre région, la fonction réseau
ne sera disponible que si le caméscope est commercialisé dans ce pays ou cette région.
Pour la clientèle canadienne
L’emploi de cet appareil doit répondre aux deux conditions suivantes : (1) cet appareil
ne doit pas causer d’interférences et (2) cet appareil doit accepter les interférences, y
compris les interférences pouvant causer un fonctionnement non souhaité de l’appareil.
Pour éviter les interférences radio et fournir une protection maximale, cet appareil doit
être utilisé en intérieur et à l’écart de fenêtres. Les appareils utilisés en extérieur doivent
obtenir une autorisation.
4-FR
Félicitations pour l’achat de ce Sony Handycam. Votre caméscope peut accéder à
Internet avec les périphériques compatibles. Vous pouvez donc effectuer les opérations
suivantes.
– Introduction –
La fonction réseau du caméscope
Envoi et réception de courrier
Vous pouvez envoyer et recevoir du courrier quand vous voulez et y joindre des
séquences vidéo ou des photos.
Accès facile à Internet
Vous pouvez voir une page web par Internet.
Réglez l’horloge du caméscope avant d’utiliser la fonction réseau. (L’horloge est
désactivée par défaut.)
Si l’horloge n’est pas réglée, vous ne pourrez pas envoyer et recevoir de courrier, ni
afficher de pages web.
Vous devez aussi faire les réglages nécessaires sur le caméscope et sur le périphérique.
Envoi et réception de
courrier
Accès facile à
Internet
9-FR
Introduction
12
9
87
6
5
4
3
Ecran de saisie de caractères
Fonctionnement de base du mode NETWORK
1Touche [abcy123]
Une liste apparaît lorsque vous tapez sur la touche [abc y 123]. Tapez
sur le type de caractères souhaité dans la liste.
2Touche [a/A]
La touche [a/A] s’affiche lorsque vous saisissez des caractères
alphabétiques.
Elle sert à sélectionner les majuscules ou les minuscules.
3Nombre d’octets saisis/Nombre d’octets maximal
4Préférences
Vous pouvez changer le type de clavier pour la saisie de caractères
alphabétiques.
5Zone de texte
Lorsque le texte est trop long, vous pouvez le faire défiler dans un sens
ou l’autre sur l’écran en tapant sur v ou V (touche de défilement) pour
voir le texte caché.
6Touche [Enter]
Tapez sur cette touche pour valider ou fermer l’écran de saisie.
7Touche
Tapez sur cette touche pour placer le curseur sur une nouvelle ligne.
8Touche [Back space]
Tapez sur cette touche pour supprimer la lettre précédant le curseur. Si
vous tenez le stylet appuyé plus de trois secondes, tous les caractères
précédant le curseur sont effacés.
9Touche [Space]
Tapez sur cette touche pour insérer un espace.
13-FR
Introduction
3(1)Tapez sur [abcy123], puis tapez sur [abc].
(2)Tapez sur [a/A] pour sélectionner les majuscules.
,
(3)Tapez sur [H].
“H” est saisi.
,
(4)Tapez sur [a/A] pour sélectionner les minuscules.
,
Fonctionnement de base du mode NETWORK


Specyfikacje produktu

Marka: Sony
Kategoria: kamera wideo
Model: dcr-ip 220

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Sony dcr-ip 220, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje kamera wideo Sony

Sony

Sony E Instrukcja

15 Stycznia 2025
Sony

Sony BRC-H780 Instrukcja

29 Grudnia 2024
Sony

Sony HDC-2400 Instrukcja

12 Października 2024
Sony

Sony PMW-350K Instrukcja

12 Października 2024
Sony

Sony DCR-IP210 Instrukcja

8 Października 2024
Sony

Sony HXR-NX30U Instrukcja

8 Października 2024
Sony

Sony NEX-EA50UH Instrukcja

8 Października 2024
Sony

Sony PXW-FS7H Instrukcja

8 Października 2024
Sony

Sony PMW-160 Instrukcja

5 Października 2024
Sony

Sony HXR-NX30N Instrukcja

5 Października 2024

Instrukcje kamera wideo

Najnowsze instrukcje dla kamera wideo