Instrukcja obsługi Sonic Alert HA360SSSC


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Sonic Alert HA360SSSC (2 stron) w kategorii Bezpieczeństwo. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/2
INSTALLATION AND SET UP FOR HOMEAWARETRANSMITTER
HA360SSSC Smoke / CO
The HomeAware Smoke/CO transmitter will alert you to the
sounds produced by the smoke and CO detectors already
installed in your home. This transmitter alerts you through the
HomeAware™ Main unit and remote receivers located in
other rooms.
Battery Backup Installation
Install a new 9 volt alkaline battery into the battery
compartment located on the back of the unit. See diagram for
battery door location. Battery backup will provide power
when a power outage has occurred. Power will be provided
for a continuous outage lasting 7 days, or for short outages
up to two years.
Link Button Set Up
This procedure will link your transmitter to your Main unit.
The Main unit will also provide an alert to all HomeAware™
remote receivers. When using the Bridge unit HA360BU all
original Sonic Alert receivers (SA101, SA201, BL300, and
SB1000) will also alert you.
It is best to do the link procedure in the same room with the
HomeAware™ Main unit, make sure the unit is plugged in.
To link a transmitter to your HomeAware™ Main unit:
1. Press set up button and the word LINK will be shown on
the display, press Enter. LINK will begin blinking.
(If LINK mode is entered by accident, simply press the
BACK button to exit and return to the clock.)
2. Press and hold down the Link button on the back of your
transmitter for about 1 second. The red LED on the
transmitter will light up. Release the button.
3. Upon successful connection, the red LED on the
transmitter will flash 2 times, then turn off. The
HomeAwaremain unit will briefly show DONE, and
return to the time display. Your transmitter is now
connected and ready to test and use.
Detecting the Different Alert Sounds
This transmitter detects loud sounds and will alert you to the
source of that sound.
When a sound is detected from the HA360SSSC it will send a
signal to the HomeAware™ base unit and all HomeAware™
remote receivers, also the red LED light will flash on the front
of the unit.
If this transmitter detects a loud sound from a smoke detector
that meets the T3 standard used for SMOKE DETECTORS,
“SMOKE” will scroll on the display of the HomeAware™ Main
Unit.
(The T3 standard is on for 0.5 sec, off for 0.5 sec, repeated 3
times, and followed by 1.5 sec of silence, as defined by NFPA
code 72.)
If the transmitter detects a loud sound from a CARBON
MONOXIDE (CO) DETECTOR that meets the T4 standard,
“CO” will scroll on the displayed of the HomeAware™ Main
Unit.
(The T4 standard is on for 0.1 sec, off for 0.1 sec, repeated 4
times, and followed by 5 sec silence, as defined by NFPA
code 720.)
For All Other Sounds
If a loud sound is detected that does NOT match the T3 or T4
standard, then “ALERT” will scroll on the HomeAware™ Main
unit in a loud, repeating pattern.
You can control the sensitivity level for the "ALERT" detection
using the switch on the back of the unit. There are three
levels to choose from: The HI setting is the most sensitive
setting and will alert you to more sounds. Moving this switch
to MED makes it less sensitive and will alert you to less
sound. The LO setting is the least sensitive. If you’re not
picking up the sound you need to be alerted to simply move
the sensitivity switch to a higher setting. If you have set this
setting to HI and you are still not picking up the sound, try
moving the transmitter closer to the sound.
Power Input
The HomeAware™ Smoke/CO transmitter uses an included
12V DC power adapter. Plug the power adapter into an 120V
AC power outlet, then plug the other end into the Low Voltage
12V DC input on the left side of the unit as show in the
diagram.
INSTALLATION AND SET UP FOR HOMEAWARE™ TRANSMITTER
HA360SSSC Smoke / CO
FCC Requirements
This device complies with part 15 of the FCC rules. Operation
is subject to the following two conditions; (1) This device
might not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC rules. These limits are designed to provide
responsible protect against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions manual, may cause
harmful interference to radio communications. However, there
is no guarantee that interference will not interfere in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment on and off, the user is
encouraged to try to correct the interference by one or more
of the following measures:
i. Reorient or relocate the receiving antenna.
ii. Increase the separation between the equipment and
receiver.
iii. Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
iv. Consult the dealer or and experienced radio /TV
technician for help
Modification not expressly approved by the manufacturer
could void the user’s authority to operate the equipment
under FCC rules.
GENERAL DATA
UL listed Power Adaptor: AC100-240V~, 50/60Hz
Power Consumption: Adaptor Output: DC12V, 250mA
The Lightening
flash and
arrowhead within
the triangle is a
warning sign
alerting you of
dangerous voltage
inside the product.
CAUTION:
TO REDUCE
THE RISK
OF ELECTRICAL
SHOCK, DO
NOT
REMOVE THE
COVER
(OR BACK)
FROM THE
PRODUCT. NO
USER
SERVICEABLE
PARTS
INSIDE. REFER
SERVICING TO
YOUR SONIC
ALERT DEALER.
The exclamation
mark within the
triangle is a
warning sign
alerting you of
important
instructions
accompanying
the product.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
The normal function of the product may be disturbed
by Strong Electro Magnetic Interference. If so, simply
reset the product to resume normal operation by
following the instruction manual. In case the function
could not resume, please use the product in other
location.
Attention should be drawn to the environmental
aspects of battery disposal.
T This indicating separate collection for electrical
and electronic equipment.
SONIC ALERT’S 1 YEAR LIMITED WARRANTY
The HomeAware™ HA360SSSC is warranted against
manufacturing defects in materials and workmanship for
one (1) year from the date of purchase. Within this
period Sonic Alert will repair or replace at our option the
HomeAware™ HA360SSSC without charge for parts
and labor.
Simply contact our customer service department
to obtain an RA (return authorization number)
and instructions on how to process your product
for return. Call 1-888-864-2446 or e-mail to
RMA@sonicalert.info. You’ll need a copy of your
receipt to process the return authorization.
Sonic Alert Warranty Center
1081 West Innovation Dr. Kearney, MO 64060, USA.
Made in China
Sonic Alert, Troy, MI 48083
www.SonicAlert.com 1-888-864-244


Specyfikacje produktu

Marka: Sonic Alert
Kategoria: Bezpieczeństwo
Model: HA360SSSC

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Sonic Alert HA360SSSC, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Bezpieczeństwo Sonic Alert

Instrukcje Bezpieczeństwo

Najnowsze instrukcje dla Bezpieczeństwo