Instrukcja obsługi Snow Joe 24V-SS12-XR-RED
Snow Joe
pług wirnikowy
24V-SS12-XR-RED
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Snow Joe 24V-SS12-XR-RED (7 stron) w kategorii pług wirnikowy. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/7
Original instructions.
© 2022 Snow Joe, LLC. All rights reserved.
A Division of Snow Joe, LLC Model 24V-SS12-XR Form No. SJ-24V-SS12-XR-880E-M
R
OPERATOR’S MANUAL
1
EN
CORDLESS SNOW SHOVEL
24V MAX* | 5.0 Ah | 12-INCH
*Initial no-load voltage, when fully charged, peaks at
24V; nominal voltage under typical load is 21.6V.
SAVE THESE INSTRUCTIONS
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Read all instructions before using this cordless snow shovel.
Basic safety precautions should always be followed to reduce
the risk of re, electric shock and personal injury.
General Safety
You and any other operator of this snow shovel must read,
understand and follow these instructions in their entirety, and
should reread them at the start of each snow season. Failure
to follow these instructions may result in ELECTRIC SHOCK,
FIRE and/or serious PERSONAL INJURY.
Notice the personal safety alert symbol m used in this
manual to draw your attention to a WARNING given along
with the particular operating instruction. This means that
the operation requires special ATTENTION, CAUTION and
AWARENESS.
mWARNING! When using the power tool, basic safety
precautions should always be followed to reduce the risk of
fire, electric shock, and personal injury. These include:
• Keep work area clean and well lit – Cluttered, dark areas
invite accidents.
• Use the right product – Do not use this machine for any
job except that for which it is intended.
• Replacement parts – When servicing this unit, use only
identical replacement parts. Replace or repair damaged
cord immediately on the charger.
Do not use on gravel surfaces unless the snow shovel
is adjusted for such surfaces in accordance with the
operator’s manual.
• Keep children, bystanders and pets away – All
spectators, including pets, should be kept a safe distance
away from the work area.
• Dress properly – Do not wear loose articles of clothing or
jewelry. They can become caught in moving parts. Wear
rubber boots.
• Avoid accidental starting – Make sure the safety switch
and the on/off switch are in the off position before
inserting the battery in the unit. Do not carry the cordless
snow shovel with the safety switch and the on/off switch
engaged.
• Moving parts – Keep hands and feet away from moving
parts. Keep guards in place and in proper working order.
• mCAUTION! Exercise caution to avoid slipping or falling.
Wear protective footwear that will protect your feet and
improve your footing on slippery surfaces.
• Use safety glasses – Also use safety footwear,
snug‑fitting clothing and gloves.
• Stay alert – Watch what you are doing. Use common
sense. Do not operate the cordless snow shovel when you
are tired or under the influence of alcohol or drugs.
• Do not force the tool – It will perform better with less
likelihood of personal or mechanical injury if it is used at
the rate for which it was designed.
• Do not overreach – Keep proper footing and balance at
all times.
• If the cordless snow shovel strikes a foreign object, follow
these steps:
i. Stop the cordless snow shovel. Remove the battery.
ii. Inspect for damage.
iii. Repair any damage before restarting and operating the
snow shovel.
• Disconnect the tool – Turn off the power switch and
remove the battery when it is not in use, before servicing
it, when changing accessories and when performing any
other maintenance task.
• Store idle tool indoors – When not in use, the cordless
snow shovel should be stored indoors in a dry, locked
place out of the reach of children.
• Maintain the cordless snow shovel with care – Follow
the applicable maintenance instructions for replacing parts
and changing accessories. Lubrication is not required.
Battery & Charger
Safety Instructions
We pay a great deal of attention to the design of every battery
pack to ensure that we supply you with batteries that are safe,
durable and have a high energy density. The battery cells have
a wide range of safety devices. Each individual cell is initially
formatted and its electrical characteristic curves are recorded.
This data is then used exclusively to assemble the best
possible battery packs.
Despite all the safety precautions, caution must always be
3
machine is only partially charged. The battery pack must
be fully charged before using the shovel for the first time.
• Lithium‑ion batteries are subject to a Battery Aging –
natural aging process. A battery pack must be replaced at
the latest when its capacity falls to just 80% of its capacity
when new. Weakened cells in an aged battery pack are no
longer capable of meeting the high power requirements
needed for the proper operation of your machine, and
therefore pose a safety risk.
• Do not exhaustively discharge battery packs –
A complete discharge will damage the battery cells. The
most common cause of exhaustive discharge is lengthy
storage. Stop working as soon as the performance of a
battery falls noticeably or the electronic protection system
triggers. For optimum battery performance, charge the
battery packs frequently. Place the battery packs in
storage only after they have been fully charged.
• Do not overload battery packs – Protect the shovel and
battery from overloading. Overloads will quickly result in
overheating and cell damage inside the battery housing
even if it is not apparent externally. For safety reasons, the
integrated protective cutoff will activate to switch off the
equipment. After regular use, allow the battery packs to
cool to room temperature before recharging them.
IMPORTANT! Do not attempt to turn on the machine if the
protective cutoff has been activated. This may damage
the battery packs.
• Outlet voltage – Please check the data marked on the
rating label of the battery charger. Be sure that the voltage
of the power supply matches that marked on the rating
label. Never connect it to a different mains voltage.
• Charger use – Do not use the supplied battery charger to
charge other types of battery packs or tools.
• Do not overcharge battery packs – Do not exceed the
maximum charging times. Frequently overcharging the
battery packs will result in cell damage. Do not leave
battery connected to the charger for days on end.
• Battery pack abnormalities – Do not use batteries that
have suffered swelling or deformation or those that exhibit
other atypical symptoms (gassing, hissing, cracking, etc.).
• Electrostatic discharge – When handling batteries, be
wary of electrostatic charge. Electrostatic discharges can
damage the electronic protection system and the battery
cells. To avoid electrostatic discharges, never touch the
battery terminals.
7
4. When the charger light turns green, the battery is fully
charged (Fig. 3).
NOTE: A fully discharged pack with an internal
temperature in the normal range will fully charge in 2 hr 20
mins (between 32ºF/0ºC and 113ºF/45ºC).
5. If the light indicators do not come on at all, check that
the battery pack is fully seated into the bay by removing
the battery pack and reinserting. If the problem persists,
contact an authorized Snow Joe® + Sun Joe® dealer or
call the Snow Joe® + Sun Joe® customer service center at
1‑866‑SNOWJOE (1‑866‑766‑9563) for assistance.
6. When charging is complete, remove the battery from the
charger by pressing the push lock buttons and sliding the
battery backward to unlock it from the charger (Fig. 4).
Battery pack
Charger
red
Charging
green
Fully
Charged
Fig. 3
Push lock
button
Fig. 4
7. Timely recharging of the battery will help prolong the
battery’s life. You must recharge the battery pack when
you notice a drop in the equipment’s power.
IMPORTANT! Never allow the battery pack to become fully
discharged as this will cause irreversible damage to the
battery.
Charging a Hot or Cold Battery Pack
The green indicator light on the charger base indicates that the
battery pack temperature is outside the charging range. Once
the pack is within the acceptable range, normal charging will
take place and the red light will be continuous. Hot or cold
battery packs may take longer to charge.
Assembly
Slide the upper pole onto the lower pole. Align the screw holes
and secure them together using the curved head bolt, saddle
washer and the remaining knob (Fig. 5).
NOTE: Carefully move the wiring inside the pole to one side if
it is in the way of the bolt.
Lithium‑Ion Charging Status
Battery Pack
Temperature
Charger
Base
Indicator
Light
Battery
Pack
Indicator
Light
Charging
Status
Too hot Green Flashing
together
Not
charging
Normal range Red Flashing
one by one
Normal
charging
Too cold Green Flashing
together
Not
charging
Fig. 5 Upper pole
Lower pole
Curved
head bolt
Saddle washer
Knob
Specyfikacje produktu
| Marka: | Snow Joe |
| Kategoria: | pług wirnikowy |
| Model: | 24V-SS12-XR-RED |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Snow Joe 24V-SS12-XR-RED, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje pług wirnikowy Snow Joe
18 Czerwca 2024
18 Czerwca 2024
18 Czerwca 2024
18 Czerwca 2024
18 Czerwca 2024
18 Czerwca 2024
18 Czerwca 2024
18 Czerwca 2024
18 Czerwca 2024
18 Czerwca 2024
Instrukcje pług wirnikowy
Najnowsze instrukcje dla pług wirnikowy
24 Września 2024
14 Maja 2024