Instrukcja obsługi SIIG CE-MT0J11-S1

SIIG Wandsteuna CE-MT0J11-S1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SIIG CE-MT0J11-S1 (8 stron) w kategorii Wandsteuna. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/8
04-0661
A
Installation Instructions
Wall distance: 1.38" / 35mm
Bubble level included
Low Profile Universal TV Mount - 42" to 70"
IMPORTANT: If you don't understand the installation instructions, please consult an installation
specialist
Fixed Flat-Panel TV Wall Mount
Universal Mounting Pattern
Material: 2.0mm Cold Rolled Steel Plate
TV Size: 42" - 70"
Max load capacity: 165lbs / 75kgs
1
A1 D (×4) M8/M6 rectangular washer
A2 E (×6) M8x50 bolt
B1 F (×6) M8 concrete anchor
B2 G1 (x6) M8 washer
C1 G2 External bubble level
C2 H
Do not install near heater, fireplace, air conditioning, in direct sunlight, or any other heat producing source. Failure to do
so may result in damage to the display and could increase the risk of fire.
INSTALLATION AND OPERATING INSTRUCTIONS
CAUTION: The maximum load capacity is 165lbs. Use with products exceeding the maximum load capacity may cause
serious injury. See apparatus instructions.
It is recommended that two people perform the installation. Injury and/or damage can result from dropping or
mishandling the display.
(×4) M6×12 screw
(×4) M8×15 screw
Recommended mounting surfaces: wood stud and solid-flat concrete. If the mount is to be installed on any surface
other than wood studs, use suitable hardware (not included but commercially available).
Prior to the installation of this product, the installation instructions should be read and completely understood. The
installation instructions must be read to prevent personal injury and property damage. Keep these installation
instructions in an easily accessible location for future reference.
When mounting to a wall that contains wood studs, confirm dead center of the wood stud prior to installation, it is
recommended that the wood studs be a minimum of 16" apart.
Caution
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in
damage to the display and/or damage to the mounting surface.
The wall structure must be capable of supporting at least the maximum load capacity as indicated. If not, the wall must
be reinforced. Proper installation procedure by yourself or a qualified service technician, as outlined in the installation
instructions, must be adhered to. Failure to do so could result in serious personal injury.
Hardware kit:
(×4) M5×30 screw
(×4) M8×30 screw
(×4) M6×30 screw
(×4) Spacer
(×4) M5×12 screw
2
1
2
3
4
A) Wood Stud Installation
3
4
5
6
7
Use a high-quality electronic stud finder to locate dead center of two
studs and mark their locations with a pencil (figure 1-a).
NOTE: When mounting to wood studs, the two wood studs must be a minimum of 16" apart.
Step1: Wall Plate Installation
1/2" Socket and Wrench
Electric drill, 3/16" (5mm) drill bit for wood stud installation and 3/8" (10mm) masonry bit for concrete/brick installation
Note: Please ensure that the bubble level (G2) is properly mounted on the wall plate prior to mounting the wall
plate.
Tighten the bolt with a 1/2" socket or open ended wrench by turning clockwise until tight.
CAUTION: Do not release the wall plate until it is properly mounted and secured to the wall.
Attach the bubble level (G2) to the wall plate and with the help of an
assistant ensure the wall plate is level, position the wall plate against
the wall in the desired mounting location.
Mark the right (upper and lower) and the left (upper and lower) positions of the small horizontal slots that are in
alignment with the studs. You should mark four positions total.
2
1
Phillips head screw driver
Stud finder for drywall installation
Tools Required:
Next, pre-drill a 3/16" hole to a depth of approximately 2" in the wood stud at each marked location.
Place the wall plate against the wall and line up the mounting slots with the drilled holes. Check the bubble level to
verify that the wall plate is level.
For each location, insert a bolt (E) and washer (G1) into the wall.
CAUTION: Do not over-tighten bolts-doing so many cause unnecessary damage to the wall. Avoid excessive torque.
3


Specyfikacje produktu

Marka: SIIG
Kategoria: Wandsteuna
Model: CE-MT0J11-S1

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z SIIG CE-MT0J11-S1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Wandsteuna SIIG

SIIG

SIIG CE-MT0A12-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT0812-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT1B12-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT0H11-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT0712-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT0212-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT0K11-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT0G11-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT0L11-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT0J11-S1 Instrukcja

3 Października 2024

Instrukcje Wandsteuna

Najnowsze instrukcje dla Wandsteuna

Bauhn

Bauhn ALPB80-0724 Instrukcja

15 Października 2024
Vogel's

Vogel's EFW 6105 Instrukcja

14 Października 2024
One For All

One For All WM 2121 Instrukcja

14 Października 2024
Vogel's

Vogel's WALL 1145 Instrukcja

13 Października 2024
My Wall

My Wall HP 103 L Instrukcja

9 Października 2024
One For All

One For All WM 4920 Instrukcja

9 Października 2024
StarTech.com

StarTech.com FPWFXBAT Instrukcja

9 Października 2024
StarTech.com

StarTech.com FPWARTB1M Instrukcja

9 Października 2024
StarTech.com

StarTech.com STNDMTVDUO Instrukcja

9 Października 2024