Instrukcja obsługi SIIG CE-MT0812-S1

SIIG Wandsteuna CE-MT0812-S1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SIIG CE-MT0812-S1 (8 stron) w kategorii Wandsteuna. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/8
04-0541A
TV Size: 32" - 55
Max load capacity: 121lbs/55kg
Wall distance: 0.43/11mm
Universal Mounting Pattern
Ultra-Thin LED/LCD TV Mount - 32" to 55"
IMPORTANT: If you don't understand the installation instructions, please consult an
installation specialist
Ultra-Thin LED/LCD TV Wall Mount
Material: 2.0mm Cold Rolled Steel Plate
Installation Instructions
1
Caution
A G
B H
C I
D J
E K
F L
(×4) M8×16 screw
(×4) M6×16 screw
(×4) M8×80 bolt
(×4) M5×35 screw (×4) Concrete anchor
(×4) M8×35 screw (x2) Sponge sticker
(×4) M6×35 screw (×4) M8 spacer
When mounting to a wall that contains wood studs, confirm dead center of the wood stud prior to installation, it is
recommended that the wood studs be a minimum of 16" apart.
It is recommended that two people perform the installation. Injury and/or damage can result from dropping or
mishandling the display.
INSTALLATION AND OPERATING INSTRUCTIONS
Do not install near heater, fireplace, air conditioning, in direct sunlight, or any other heat producing source.
Failure to do so may result in damage to the display and could increase the risk of fire.
The wall structure must be capable of supporting at least the maximum load capacity as indicated. If not, the
wall must be reinforced. Proper installation procedure by yourself or a qualified service technician, as outlined in
the installation instructions, must be adhered to. Failure to do so could result in serious personal injury.
Recommended mounting surfaces: wood stud and solid-flat concrete. If the mount is to be installed on any
surface other than wood studs or concrete, use suitable hardware (not included but commercially available).
Prior to the installation of this product, the installation instructions should be read and completely understood.
The installation instructions must be read to prevent personal injury and property damage. Keep these
installation instructions in an easily accessible location for future reference.
CAUTION: The maximum load capacity is 121 lbs. Use with products exceeding the maximum load capacity may
cause serious injury. See apparatus instructions.
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could
result in damage to the display and/or damage to the mounting surface.
Hardware Kit
(×4) M5×16 screw (×4) M6 washer
(x4) M5 washer
2
1
2
3
4
5
3
4
5
7
8
a) Wood Stud Installation
You should mark two positions total.
Stud finder for drywall installation
NOTE: When mounting to wood studs, the two wood studs must be a minimum of 16" apart.
Use a high-quality electronic stud finder (commercially available) to locate dead center of two studs and mark
their locations with a pencil.
Step 1: Wall Plate Installation
1
2With the help of an assistant, and using a bubble level to ensure the wall plate is level, position the wall plate
against the wall in the desired mounting location.
Mark the right and the left positions of the small horizontal slots that are in alignment with the studs.
Tools Required
Phillips head screw driver
Tighten the bolt with the 1/2" socket or 1/2" open-end wrench by turning clockwise until tight.
For each location, insert bolt (I) into the wall.
Pre-drill a 3/16" hole to a depth of approximately 3" in the wall stud at each marked location.
Level
1/2" socket & socket wrench and/or 1/2" open-end wrench
Drill, 3/16" (5mm) drill bit for wood stud installation and 3/8" (10mm) masonry drill bit for concrete/brick installation
CAUTION: Do not release the wall plate until it is properly mounted and secured to the wall.
6Place the wall plate against the wall and line up the mounting slots with the drilled holes. Check the bubble level
to verify that the wall plate is level.
CAUTION: Do not over-tighten bolts - doing so may cause unnecessary damage to the wall.
3


Specyfikacje produktu

Marka: SIIG
Kategoria: Wandsteuna
Model: CE-MT0812-S1

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z SIIG CE-MT0812-S1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Wandsteuna SIIG

SIIG

SIIG CE-MT0A12-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT0812-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT1B12-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT0H11-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT0712-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT0212-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT0K11-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT0G11-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT0L11-S1 Instrukcja

3 Października 2024
SIIG

SIIG CE-MT0J11-S1 Instrukcja

3 Października 2024

Instrukcje Wandsteuna

Najnowsze instrukcje dla Wandsteuna

Bauhn

Bauhn ALPB80-0724 Instrukcja

15 Października 2024
Vogel's

Vogel's EFW 6105 Instrukcja

14 Października 2024
One For All

One For All WM 2121 Instrukcja

14 Października 2024
Vogel's

Vogel's WALL 1145 Instrukcja

13 Października 2024
My Wall

My Wall HP 103 L Instrukcja

9 Października 2024
One For All

One For All WM 4920 Instrukcja

9 Października 2024
StarTech.com

StarTech.com FPWFXBAT Instrukcja

9 Października 2024
StarTech.com

StarTech.com FPWARTB1M Instrukcja

9 Października 2024
StarTech.com

StarTech.com STNDMTVDUO Instrukcja

9 Października 2024