Instrukcja obsługi Scott i-CX 2

Scott Kołyska/stacja dokująca i-CX 2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Scott i-CX 2 (4 stron) w kategorii Kołyska/stacja dokująca. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

i-CX 2

ALARM CLOCK RADIO

WITH iPod DOCKING STATION

Instruction Manual

GB-1

PRECAUTIONS

Follow the advice below for safe and appropriate operations.

PLACEMENT

. Do not use the unit in places which are extremely hot, cold, dusty, or humid.

. Place the unit on a flat and even surface.

. Do not restrict the airflow of the unit by placing it in a place with poor airflow, by covering it with a

cloth, or by placing it on a carpet.

. Do not place naked flame sources, such as lighted candles on the apparatus.

. Use the apparatus only in moderate climates (not in tropical climates).

. Do not expose the apparatus to dripping or splashing.

. Do not place objects filled with liquids, such as vases, on the apparatus.

SAFETY

. When connecting and disconnecting the AC power cord from the AC mains outlet, pull the plug and

not the cord itself. Pulling the cord may damage it and may be dangerous.

. The mains outlet and plug must always remain readily operable.

. When you are not going to use the unit for a long period of time, disconnect the AC power cord from

the AC mains outlet.

AC VOLTAGE

. Before use, check that the rated voltage of your unit matches your local voltage.

CONDENSATION

. When there is condensation inside the unit, it may not function normally.

. Let the unit stand for 1 to 2 hours before turning the power on, or gradually heat the room up and

dry the unit before use.

. Ensure a minimum distance of 5 cm around the apparatus for sufficient ventilation.

. Ensure that the ventilation is not impeded by covering the ventilation openings with items such as

newspapers, tablecloths, curtains, etc.

BATTERIES

. Pay attention to the environmental aspects of battery disposal.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with an

arrowhead symbol within a

triangle is a warning sign

alerting the user to the

presence of “dangerous

voltage” inside the unit.

ATTENTION: To reduce the risk

of electric shock, do not remove

the cover. There are no user

serviceable parts inside the unit.

Refer all servicing to qualified

personnel.

The exclamation mark

within a triangle is a

warning sign alerting the

user to the presence of

important instructions

accompanying the

product.

. In case of malfunction due to electrostatic discharge, the apparatus has to be reset by disconnecting

it from mains supply.

GB-2

1234 561

15171819

TABLE OF CONTENTS

PRECAUTIONS 1

TABLE OF CONTENTS 2

BOX CONTENTS 2

LOCATION OF CONTROLS 2

POWER SUPPLY 3

BASIC OPERATION 3

RADIO OPERATION 4

PLAYING AN iPod AND CHARGING THE INTERNAL iPod BATTERY 5

AUX IN FUNCTION 6

AUX OUT FUNCTION 6

MAINTENANCE 6

TROUBLESHOOTING GUIDE 7

TECHNICAL SPECIFICATIONS 7

BOX CONTENTS

1. Unit

2. Adapters for different iPod models (7x)

3. Instruction manual

LOCATION OF CONTROLS

1. Speakers (2x)

2. AC power cord

3. AUX IN jack

4. AUX OUT jack

5. DIMMER HI-LO switch

6. FM antenna wire

7. iPod docking station and connector

8. AM/FM/iPod/AUX switch

9. ALARM SET/OFF button

10. CLK SET button

11. Tuning scale

12. dial TUNING

13. MIN (Minute set) button

14. SNOOZE button

15. FM STEREO LED indicator

16. ON LED indicator

17. Clock back up battery door

18. Clock display

19. Alarm indicator

20. HR (Hour set) button

21. SLEEP button

22. VOLUME dial

23. / , SKIP/SEARCH, PLAY/PAUSE buttons

24. ON button

25. AUTO OFF/MUSIC/BUZZER switch

GB-3

POWER SUPPLY

AC power supply

Insert the AC power cord into the AC mains outlet with a 230V AC ~ 50Hz power source.

Installing the clock back up battery

If the AC cord is disconnected or there is a power failure, this electronic clock is designed to continue

operating internally (without showing the time on the display) with a 9 volt battery (type 6F22, not

included). To install the battery, open the clock back up battery door on the bottom of the unit.

Connect the battery to the terminals of the battery snap inside the compartment (use of an alkaline

battery is recommended) and close the battery door.

After a power failure, the clock time should continue operating. If a flashing time appears on the

display, it indicates the battery is dead or not connected properly. The 9 volt battery will keep the

clock time accurately for approximately 30 minutes. If the power is restored after 30 minutes, the time

may need to be reset.

Precautions when using batteries

1. Replace only with an identical battery or an equivalent type.

2. An exhausted battery must be removed to prevent any battery leakage.

3. Dispose of the battery properly according to environmental regulations.

BASIC OPERATION

ON/ Standby mode

After connecting the power supply (refer to POWER SUPPLY), the unit goes to standby mode and

the clock time is displayed. Press the ON button to turn on the unit and the ON LED indicator lights

up. Press it again to go to standby mode.

Clock time setting

Set the clock

1. Hold down the CLK SET button and press the HR button to set the hours.

2. Hold down the CLK SET button and press the MIN button to set the minutes.

Set the alarm time

1. Hold down the AL SET/OFF button and press the HR button to set the hours.

2. Hold down the AL SET/OFF button and press the MIN button to set the minutes.

Alarm operation

The unit allows you to wake up to a buzzer or to music (AM/FM/iPod).

1. Press and hold down the AL SET/OFF button to display the alarm time.

2. To adjust the alarm time, follow the steps in “Set the alarm time”.

3. To enable the alarm function, slide the AUTO OFF/MUSIC/BUZZER switch to MUSIC if you want

to wake up to music or BUZZER if you want to wake up to the sound of the buzzer. The ALARM

indicator at bottom left corner of the display lights up.

When you choose to wake up to music, the alarm clock radio will start to play the last track it

played before the unit was switched off. This means you can choose which song you will to wake

up to.

4. If MUSIC mode is selected, slide the AM/FM/iPod/AUX switch to select the desired alarm source.

5. When the preset alarm time is reached, the buzzer or music will start up.

6. To stop the alarm, press the AL SET/OFF button. The alarm will sound again at the same time the

next day.

7. To disable the alarm function, slide the AUTO OFF/MUSIC/BUZZER switch to AUTO OFF.

GB-4

Note:

• While the buzzer alarm volume is fixed and cannot be adjusted, the music alarm volume can be

adjusted to your desired level using the VOLUME dial.

• If iPOD/AUX mode is selected, make sure the iPod is inserted in the docking station and the

volume is set to a suitable level.

Snooze function

When the alarm sounds, press the button to stop the alarm temporarily and it will sound SNOOZE

again after 9 minutes. To cancel the SNOOZE function and repeat the alarm the next day, press the

AL SET/OFF button.

Sleep function

This function allows you to program the radio to switch off after a specific time has passed (up to 1

hour and 59 minutes).

1. In standby mode, press and hold down the SLEEP button, and “0:59” is displayed. The unit turns

on.

2. Hold down the SLEEP button and press the MIN button to select the duration: 59, 58…. each time

you press the button the duration decreases until it reaches 0.

3. To set the duration longer than 59 minutes, hold down the SLEEP button and press the HR button.

The duration will be increased by one hour. Keep holding down the SLEEP button and press the

MIN button to adjust the minutes.

4. When the preset sleep duration elapses, the unit turns off automatically.

5. To cancel the sleep function before the preset sleep duration elapses, press the SNOOZE or ON

button to turn off the unit immediately.

Dimmer control

Slide the DIMMER HI-LO switch to set the clock display brightness.

RADIO OPERATION

Listening to the radio

1. Press the ON button to turn on the unit.

2. Slide the AM/FM/iPod/AUX switch to AM or FM.

3. Turn the TUNING dial to receive a radio station. The tuning scale shows the selected frequency.

If a stereo FM station is received, the FM ST LED indicator will light up.

4. Adjust sound volume level by turning the VOLUME dial.

5. To turn off the unit, press the ON button.

Achieve optimum reception

In FM mode, extend and position the FM antenna to achieve optimum reception.

In AM mode, orientate the unit to achieve optimum reception.

GB-5

PLAYING AN iPod AND CHARGING THE INTERNAL iPod BATTERY

Installing an adapter on the iPod docking station

1. Select the iPod adapter that corresponds to your iPod model from the

table below.

2. Install the adapter with the two tabs facing the front, by pushing it down in

the iPod docking station at the top of the unit.

3. To remove the adapter, press at the back of the adapter and pull it up.

iPod dock

adapter No.

iPod description Capacity

6 iPod (4th generation)

iPod (4th generation) with color display 20GB

20 GB & 30GB

7 iPod (4th generation)

iPod (4th generation) with color display 40GB

40GB & 60GB

8 iPod nano (1st generation)

iPod nano (2nd generation) 1GB, 2GB & 4GB

2GB, 4GB & 8GB

9 iPod (5th generation) with video

iPod classic 30GB

80GB

10 iPod (5th generation) with video

iPod classic 60GB & 80GB

160GB

13 iPod nano (3rd

generation) 4GB & 8GB

14 iPod touch 8GB & 16GB

Note: Ensure that you use the adapter corresponding to your iPod in order to ensure that it is

installed in a stable way and that the electrical contact is good.

Listening to your iPod

1. With the correct iPod adapter installed, gently place the iPod (without the protective cover) in the

docking station.

2. Slide the AM/FM/iPod/AUX switch to iPOD/AUX.

3. Press the ON button. Both units will be turned on and the music in the iPod will play automatically.

4. During playback, press the button to pause playback. Press it again to resume normal playback.

5. Press the / buttons repeatedly to skip to the previous or next track.

6. Press and hold down the / buttons to fast search backwards or forwards.

7. Alternatively, you can use the buttons on your iPod to carry out these operations.

Note:

• The internal iPod battery will charge until it is fully charged. Adjust the volume control on the unit

to the desired volume level.

• To prevent sound distortion during iPod playback on this unit, the EQ function in your iPod must

be set to “Off”.

• The docking station is not designed for playing and charging an iPod Shuffle, but it is possible to

connect the iPod’s line out or headphones jack to the unit’s AUX IN jack.

Specyfikacje produktu

Marka:	Scott
Kategoria:	Kołyska/stacja dokująca
Model:	i-CX 2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Scott i-CX 2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Kołyska/stacja dokująca Scott

Scott i-SX 90 Instrukcja

7 Września 2024

Scott ADX 90 R Instrukcja

5 Września 2024

Scott I-CX 3 Instrukcja

28 Sierpnia 2024

Scott I-SX 10 SL Instrukcja

18 Sierpnia 2024

Scott i-PX 12 Helin Instrukcja

18 Sierpnia 2024

Scott I-SX 50 BK Instrukcja

17 Sierpnia 2024

Scott i-CX 6 Pearl Instrukcja

16 Sierpnia 2024

Scott i-CX 2 Instrukcja

14 Sierpnia 2024

Scott I-SX 50 RS Instrukcja

7 Sierpnia 2024

Scott I-SX 10 LB Instrukcja

6 Sierpnia 2024

Instrukcje Kołyska/stacja dokująca

Najnowsze instrukcje dla Kołyska/stacja dokująca

Pyle PHST92IBK Instrukcja

15 Stycznia 2025

Polk BOOM Bit Instrukcja

13 Stycznia 2025

Anker SoundCore Flare Instrukcja

11 Stycznia 2025

Magnavox MMA3645 Instrukcja

7 Stycznia 2025

Magnavox MMA3639 Instrukcja

7 Stycznia 2025

BenQ beCreatus GR10 Instrukcja

3 Stycznia 2025

IOPLEE IOPEXTSPKER405G Instrukcja

2 Stycznia 2025

LogiLink QP0027 Instrukcja

1 Stycznia 2025

LogiLink QP0026 Instrukcja

1 Stycznia 2025

LogiLink QP0029 Instrukcja

1 Stycznia 2025