Instrukcja obsługi Sanwa YX360TRF

Sanwa multimetr YX360TRF

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Sanwa YX360TRF (3 stron) w kategorii multimetr. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

*1 Not including the resistance of fuse.

*2 The maximum value when the pointer was moved by

charged current in the capacitor.

DCVCV

DCACV

0.1 ±5 % against

full scale

±5 % against

full scale

±4 % against

full scale

±3 % against

full scale

±3 % against

full scale

±3 % against

full scale

±3 % of arc

±5 % of arc

Approximate Value

Input impedance 20 k /VΩ

Input impedance 40 k

Ω/V

Input impedance 9 k /VΩ

Current across test pins

Input impedance 9 k

Ω/V

30 Hz ~ 100 kHz within

±3 % f.s. (AC 10 V range)

Center value 20 Ω

Max. value 2 kΩ

Release voltage 3 V

*1 Voltage drop 0.1 V

*1 Voltage drop 0.25 V

Input impedance 9 kΩ/V

250/1000

10/50/250/750

2.5 m/25 m/0.25

2 k/20 k/200 k/2 M

(X1/X10/ X100/ X1 K)

-10 dB

~ +

22 dB

(for 10 VAC)

~ +

62 dB

0 ~ 150 mA at X1 range

0 ~ 15 mA at X10 range

0 ~ 1.5 mA at X100 range

0 ~ 150 µA at X1 K range

0 ~

1.5 µA at X100 K range

200 M

(X100 K)

DC 25 kV

1000 atX10 range

HV-10T probe

HFE-6T probe

DCV

(NULL)

ACV ~

HV (DC

high volt)

hFE

Use the optional probe

YX360TRF

MULTITESTER

INSTRUCTION MANUAL

05-130620402040

SANWA ELECTRIC

INSTRUMENT CO.,LTD.

Dempa Bldg., 4-4 Sotokanda 2-Chome

Chiyoda-Ku,Tokyo,Japan

NAMES OF COMPONENTS

Test probe (black)

Test pins

Finger guards

Test probe (red)

Removable

test pin covers

When not

covered

− 1 − − 2− − 3−

INTRODUCTION

Thank you for purchasing a SANWA tester Model YX360TRF. You are

kindly requested to thoroughly read this manual before use for safety.

Especially, “SAFETY INFORMATION” and “MEASURING PROCE-

DURE” are important. Keep this manual together with the tester so as

no to lose it.

Fig. 1

SAFETY INFORMATION

SPECIFICATIONS

The following are precautions to prevent accidents such as electrical

shocks.

Be sure to read them before using the tester.

Symbols

The following cautionary signs appear on the multitester and

in this manual.

Disobedience to instructions with this sign may lead to trouble

with the tester and accidents such as electrical shock.

This sign cautions that high voltage is applied to parts marked

with it.

Precautions for Safety Measurement

To ensure that the meter is used safely, follow all safety and operat-

ing instructions.

11. Never use the meter on the electric circuits that exceeds 3 kVA.

12. Pay special attention when measuring the voltage of AC 33 Vrms

(46.7 V peak) or DC 70 V or more to avoid injury.

13. Never apply input signals exceeding the maximum rating input

value.

14. Never use the meter for measuring the line connected with equip-

ment (i.e. motors) that generates induced or surge voltage since it

may exceed the maximum allowable voltage.

15. Never use the meter if the meter or test leads are damaged or broken.

16. Never use an uncased meter.

17. Be sure to use a fuse of the specified rating or type. Never use a

substitute of the fuse or make a short circuit of the fuse.

18. Always keep your fingers behind the finger guards on the probe

when making measurements.

19. Be sure to disconnect the test pins from the circuit when changing

the function or range.

10. Before starting measurement, make sure that the function and

range are properly set in accordance with the measurement.

11. Never use the meter with wet hands or in a damp environment.

12. Never use test leads other than the specified type.

13. Never open the case except when replacing batteries or fuses. Do

not attempt any alteration of original specifications.

14. To ensure safety and maintain accuracy, calibrate and check the

meter at least once a year.

15. Indoor use only.

WARNING

− 5− − 6− − 7−

BODY COVER, TEST LEADS, HAND STRAP

Use of Cover (example for the body cover)

When this tester is out of use:

Attach the cover to the panel face for safekeeping.

When measuring:

Attach it either to the rear case side

or use it as a stand as shown below.

Storage of Test Leads

When placing the test leads in the

storage space, roll it 3 times, then

put in the test pin side first as shown

below.

Attachment of Hand Strap

1 Loosen the screws fixing the rear

case and remove it.

2 Hand strap is attached to con-

necting point.

3 Put back the rear case where it

was and fix it with the screws.

Fig. 2

− 4−

SCALE READING

Range Multiplied

ΩX 100 k X 100 k

ΩX 1 k X 1 k

ΩX 100 X 100

ΩX 10 X 10

ΩX 1 X 1

DCV 250 X 1

DCV 2.5 X 0.01

DCV 0.25 X 0.001

ACV 250 X 1

DCA 0.25 X 0.001

DCA 25 m X 0.1

DCA 2.5 m X 0.01

DCV 50 X 1

ACV 50 X 1

DCA 50 µ X 1

DCV 0.1 X 0.01

Range Multiplied

DCV 10 X 1

DCV 1000 X 100

ACV 750 X 100

ACV 10 X 1

C (µF) X 1

DCV ± 25 X 1

DCV ± 5 X 1

150 mA at X 1 X 10

15 mA at X 10 X 1

1.5 mA at X 100 X 0.1

150 µA at X 1 k X 10

1.5 µA at X 100 k X 0.1

LV X 1

hFE X 1

ACV 10 X 1

ACV 50 14 dB added

ACV 250 28 dB added

ACV 750 40 dB added

General Specifications

(Temperature : 23±2 ˚C humidity 75 % RH max. No condensation)

Drop shock proof A taut-band structure is adopted in the meter part.

The meter part is designed to withstand shock.

Circuit protection

The circuit is protected by fuse even when voltage of up

to AC 230 V is impressed on each range for 5 seconds.

Internal battery

Internal fuse

R6 (IEC) or UM-3 1.5 V X 2

F500 mAH/250 V Ø5.2 X 20 mm Fast acting fuse

Operating temperature

and humidity range

5 ~ 31 ˚C, 80 %RH max.

31< ~ 40 ˚C, 80 ~ 50 %RH (decreasing linearly)

Withstand voltage

Dimensions and mass

6 kV AC (1 min.) between input terminal and case

159.5 X 129 X 41.5 mm/ approx. 320

Storage temperature/

Humidity -10 ~ 50 ˚C 70 %RH max. No condensation

noitacificepSsmetI

Application

This instrument is portable multitester designated for meas-

urement of weak current circuits.

The specifications described in this manual are subject to

change without notice.

Measurement Range and Accuracy

Function Full scale value Accuracy Remarks

0.25/2.5/10/50 ±3 % against

full scale

APPLICATION

• HV probe, HV-10T • h

probe, HFE-6T • Test lead for repair, TL-6ITb

Accessories Instruction manual 1, Hand strap 1,

Environmental condition

Operating a ltiude up to 2000 m pollution degree 2

・

− 8− − 9− − 10− − 11−

MEASURING PROCEDURE

Measuring DCV

1 Set the range selector knob to

an appropriate DCV range.

2 Apply the black test pin to the

negative potential, and the red

test pin to the positive poten-

tial of the circuit.

3 Read the movement of the

pointer by V and A scale.

WARNING

Confirm the range of use before measurement.

Preparation for Measurement

1 Adjustment of meter zero position:

Turn the zero position adjuster so that the pointer may align

right to the zero position.

2 Range selection:

Select a proper range for the item to be measured and set

the range selector knob accordingly.

When determining a measuring range, select a one higher

voltage than the value to be measured as well as where the

pointer of a meter moves to a considerable extent.

However, select the maximum range and measure in case

the extent of value to be measured can not be predicted.

NOTE

Measuring ±DCV (NULL)

1 Set the range selector knob to

an appropriate ±DCV (NULL)

range.

Turn the 0

Ωadjuster so

th at the p ointer m ay align

exactly to 0 by ±DCV scale.

3 Apply the black test pin to the

negative potential side, and

the red test pin to the positive

potential side of the circuit.

4 Read the movement of the pointer by ±DCV scale.

Fig. 3

Measuring ACV 〜

1 Turn the range selector knob to an appropriate ACV range.

2 Apply the test leads to the circuit to be measured.

3 Read the movement of the pointer by V and A scale. (Use

AC 10 V scale for 10 V range only.)

•Since this instrument provides

the mean value system for its AC

voltage measurement circuit, AC

waveform other than sine wave

may cause an error.

•Errors occur under such frequen-

cies other than those in the speci-

fication table.

Measuring DCA

1 Turn the range selector knob to an appropriate DCA range.

2 Take out the circuit to be measured and apply the black test

pin to the negative potential,

and the red test pin to the

positive potential of the cir-

cuit.

3 Read the movement of the

pointer by V and A scale.

WARNING

Connect the meter in series with the load.

Cut off.

Fig. 4

Fig. 5

Measuring Ω

1 Turn the range selector knob to an appropriate Ωrange.

2 Short the red and black test pins and turn the 0 adjuster soΩ

that the pointer may align exactly to 0 . (If the pointer failsΩ

to swing up to 0 even when the 0 adjuster is turnedΩ Ω

clockwise fully, replace the internal battery with a fresh one.)

3 Ap ply the tes t pin to me asur

resistance.

4 Read the movement of the point-

er by scale.Ω

Note: T he p ol arity of + and - is

re verse to that of t he te st

leads when measurement is

done in range.Ω

Note: How to replace battery.

1 Loosen the screws fixing the rear

case and remove it.

2 Replace R6 (UM-3) to fresh dry

batterise.

3 Put back the rear case where it

was, and fix it with the screws.

Note:

Be sure to use the same rated

fuse. In case a fuse other than

the same rate (see “SPECIFICATIONS“) is used, an error in

indication occurs and/or circuit protection is made unable.

WARNING

Do not measure the resistance in a circuit where

a voltage is present.

Fig. 6

Fig. 7

Measuring Capacity (C)

1 Set the range selector knob to C(µF) .

2 Measure the capacitance by applying

the test pin to the capacitor to be meas-

ured after the 0 adjustment is madeΩ

in the same manner as in the resist-

ance measurement.

3 The pointer moves full scale by the charge current to the

capacitor. However, the pointer gradually starts returning to its

original position. Read the indicated maximum value on C(µF)

scale.

Note: Be sure to short circuit the both ends of the capacitor for

discharge prior to the initial measurement or in such case

after the measurement is made.

Note: Pay due attention to the polarity (+ and -) of the capacitor.

(Connect + side of the capacitor to - side of the meter.)

Measuring AF Output (dB)

dB (decibel) is measured in the same way as the ACV

measurement, but by reading the dB scale instead.

For measurement on the 10 V range, the dB scale (- 10 dB ~

+22 dB) is read directly, but, when measured on the 50 V

range, 14 dB is added. On the 250 V range, 28 dB is added to

the reading on the scale, and on the 1000 V range, 40 dB

added.

Thus, the maximum dB readable is 22 + 40 = 62 (dB) meas-

ured on the 1000 V range.

Note: Cut direct current with a capacitor of 0.1 µF or more when

measuring such signal as having direct current.

Fig. 8

− 12− − 13− − 14− − 15−

MEASURING PROCEDURE

Measuring of Iceo (Leak Current) for Transistor

1 Adjust 0 by setting the range selector Ω

knob to a proper range from X1 ~ X1 k.

2 For NPN transistor, apply a black test

lead to the collector and a red one to

the emitter.

For PNP transistor, the red one to the col-

lector and the black one to the emitter.

3 Determine the leak current by ICEO

scale indicated on the scale plate. (Unit

in µA, mA)

Measuring of Diode (including LED)

1 Adjust 0 by setting the range selector knob to a proper Ω

range from X1 (150 mA) ~ X100 k (1.5 µA).

2 Apply the black test lead to anode side and the red one to

cathode side when measuring IF (forward current). Apply

the black test lead to cathode side and the red one to anode

side when measuring IR (reverse current).

3 Read the indicated value by LI

scale. (The pointer moves to a

considerable extent for IF, and

little extent for IR)

4 The value indicated on LV scale

during the measurement is the

forward voltage of diode.

NPN B

blackred

PNP B

redblack

A K

Fig. 9

Fig. 10

USAGE OF OPTIONAL PROBES

Usage of High Voltage Probe (HV-10T)

Up to DC 25 kV of CRT anode voltage can be measured by

connecting optional HV-10T probe.

WARNING

•Keep the hand (finger) away from high voltage

power supply. Electric shock may occur due to dis-

charge.

•Measurement should be limited only to micro cur-

rent circuits.

1 Turn the range selector knob and set it to HV PROBE (DC

2.5 V range).

2 Connect the jack of the black lead of the probe to the black

test pin, and the jack of the red lead to the red test pin.

3 Apply the probe clip to the earth side and the measuring pin

to the point to be measured.

4 Read out measured value on 0 ~ 250 of V scale in kV unit

after multiplying it by 0.1.

Usage of hFE PROBE (HFE-6T)

1 Set the range selector knob to X10 range ( h

FE PROBE).

2 Short circuit both the red and black test pins to adjust 0 .Ω

3 Connect the black test pin to the probe jack when a transis-

tor to be measured is NPN, and the red pin to the probe

jack for PNP transistor.

4 Connect the black clip of the probe to the transistor base

and the red clip to the collector.

5 Connect the remaining test lead to the emitter and measure

hFE.

6 Read the indicated value of the meter on hFE scale.

MAINTENANCE

How to Replace the Fuse

If voltage over 100 V is applied

to DCA and ranges, the fuseΩ

may blow out to protect the

circuit.

1 Loosen the screws fixing the

rear case and remove it.

2 Pull the fuse out of holder on the

circuit board and replace it.(Fig. 11)

3 Put back the rear case where it was and tighten the screws.

4 Check and see whether or not indications of respective

ranges are normal (check other parts for any failures).

Storage and Other Precautions

1 Avoid giving the meter any excessive shock or vibration by

loading it on the motorbike, for instance.

2 Keep off dust and moisture from the meter.

3 Do not leave the meter for a long time in places of a high

temperature (higher than 55 ˚C), a high humidity (higher than

80 %), and dew condensation.

4 The meter cover is treated with antistatic coating. Do not

wipe it hard or clean it with volatile solvent. Use a soft

brush to remove dust.

Fig. 11

AFTER - SALES SERVICE

Warranty and Provision

Under Sanwa's general warranty policy, each instrument is war-

ranted to be free from defects in workmanship or material

under normal use for the period of one (1) year from the date of

purchase.

This warranty policy is valid within the country of purchase only,

and applied only to the product purchased from Sanwa author-

ized agent or distributor.

This warranty does not apply to fuses, disposables batteries, or

any product or parts, which have been subject to one of the fol-

lowing causes:

1. A failure due to improper handling or use that deviates

the instruction manual.

2. A failure due to inadequate repair or modification by peo-

ple other than Sanwa service personnel.

3. A failure due to causes not attributable to this product

such as fire, flood and other natural disaster.

4. Non-operation due to a discharged battery.

5. A failure or damage due to transportation, relocation or

dropping after the purchase.

Repair

Please contact Sanwa authorized agent/distributor/service

provider, listed in our website, in your country with your

information.

SANWA web site

http://www.sanwa-meter.co.jp

E-mail: exp_sales@sanwa-meter.co.jp

1.5 V×2

Specyfikacje produktu

Marka:	Sanwa
Kategoria:	multimetr
Model:	YX360TRF

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Sanwa YX360TRF, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje multimetr Sanwa

Sanwa YX-361TR Instrukcja

30 Września 2024

Sanwa YX360TRF Instrukcja

30 Września 2024

Sanwa SP21 Instrukcja

30 Września 2024

Sanwa VS-100 Instrukcja

30 Września 2024

Sanwa SP-18D Instrukcja

30 Września 2024

Sanwa EM7000 Instrukcja

30 Września 2024

Sanwa AP33 Instrukcja

30 Września 2024

Sanwa CX506a Instrukcja

30 Września 2024

Sanwa CD732 Instrukcja

30 Września 2024

Sanwa PM33a Instrukcja

30 Września 2024

Instrukcje multimetr

Najnowsze instrukcje dla multimetr

Voltcraft PMM 3005-20 Instrukcja

9 Października 2024

Bearware 306998 Instrukcja

9 Października 2024

Bearware 307001 Instrukcja

9 Października 2024

Fluke 283 FC Instrukcja

9 Października 2024

Noyafa NF-5330C Instrukcja

9 Października 2024

Noyafa NF-5310B Instrukcja

9 Października 2024

Emos M3216 Instrukcja

8 Października 2024

Uni-T UT121B Instrukcja

7 Października 2024

Maxwell MX-25103 Instrukcja

6 Października 2024

Velleman DVM840 Instrukcja

5 Października 2024