Instrukcja obsługi SAB Heli Division Head HPS3 - H0640-K
SAB Heli Division
Budowa modelu
Head HPS3 - H0640-K
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SAB Heli Division Head HPS3 - H0640-K (2 stron) w kategorii Budowa modelu. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
Approx 45 mm
11mm
Linkage Rod A Assembly . . . .x3
(Initial length for the rods from the
swashplate to the Blade Grip.)
Please read this user manual carefully, it contains instructions for the correct assembly of the KIT.
Please refer to the website www.goblin-helicopter.com for updates and other important information. Thanks You.
Blade Grip Linkage Assembly
Head Cap
Screw M2.5x15mm
(HC028-S)
Flanged Bearing
2.5x
6x2.5
(HC400-S)
Bushing
[H0599]
Blade Grip Linkage
(H0598-S)
Linkage Rod
(H0561-S)
Plastic Ball Link
(H0403-S)
Center Hub Assembly
Center Hub
(H0595-S)
Spindle
(H0596-S)
Uniball M2
(H0538-S)
Uniball M2
(H0538-S)
Uniball M2
(H0537-S)
Swashplate
Assembly
(H0600-S)
Swashplate Assembly
Blade Grip Assembly
Head Cap
Screw M2.5x8mm
(HC020-S)
Bearing
5x
10x4mm
(HC411-S)
Blade Grip Arm
(H0597-S)
Main Blade Grip
(H0513-S)
Washer
7.5x
10x0.5
(H0349-S)
Thrust Bearing
5x
10x4mm
(HC435-S)
Blade Grip Linkage
Assembly
Head Cap Screws
Shoulder M3x16mm
(HC074-S)
Nylon Nut M3
(HC206-S)
Nylon Nut M3
(HC206-S)
Head Cap Screws
Shoulder M3x18
(HC079-S)
Blade Grip
Assembly
C Washer
5x
7x0.2mm
(HC449-S)
[HC449-S]
[H0513-S][H0595-S]
Note
eg: Microlube GL261
HEX 2.5 Inside
Button Head Cap
Screw M4x6mm
(HC096-S)
Bearing
5x
10x4mm
(HC411-S)
A27_Rev 01
Page 1
HPS3 ROTOR HEAD
[
H0640-K
]
Swashplate
[H0600-S]
- 1 x Swashplate Assembly.
- 5 x UniBall M2
4.7H3.
- 1 x UniBall M2
4.7H20.
Radius Arm
[H0421-S]
- 1 x Center Hub.
- 1 x Socket Head Cap Screw Shouldered M3x16mm.
- 1 x Metric Hex Nylon Nut M3.
Center Hub
[H0595-S]
- 2 x Radius Arms.
- 2 x Spacer Arm
3x
5x2.7mm.
- 1 x Spacer Hex.
- 1 x Uniball Radius Arms.
- 2 x Socket Head Cap Screws M3x16mm.
- 2 x Socket Head Cap Screws M2.5x10mm.
- 2 x Flanged Bearings
2.5x
6x2.5mm.
- 4 x Flanged Bearings
3x
7x3mm.
Linkage
[H0598-S]
- 1 x Linkages.
- 1 x
Linkage Rod
.
- 1 x Bushing.
- 2 x Flanged Bearings
2.5x
6x2.5mm.
Damper Derlin
[H0426-S]
- 3 x H0426-A.
- 3 x H0426-B.
- 3 x H0426-C.
- 3 x Washers
10x
16x1mm.
- 3 x Washers
10x
16x0.2mm.
- 3 x Orings 3050.
Recommendations
- These parts should be used only with models SAB Goblin
- Please follow all the instructions shown in the Goblin main manual. In this manual please read Chapther 2, Important notes
- Use Loctite on all threads.
- Put a small amount of grease inside the hub and the O-Ring.
- Check for axial play of the spindle at least after the first 10 flights and add shims if necessary.
- Firmly tighten the blades before flight.
About HPS
HPS stands for "High Precision System". This head has been
developed in order to increase the usable rotor RPM range without
having to change the rigidity of the dampening system.
The new head is developed specially to limit the teetering effect of
the spindle by means of dampening achieved by a special
technopolymer material.
The maximum teetering amount can be adjusted based on the
amount of play shown in figure "A" of the drawing. The O-ring is
necessary to create a radial and axial preload.
The preload can be kept relatively low, thanks to the mechanical
locking properties of the technopolymer dampeners.
With this solution, finding the correct preload is less complex.
This solution is safer because there is a physical "stop" of the
teetering effect with the technopolymer dampers, also with low
axial preload.
The change of preload will serve exclusively to customize the
response of the model.
Furthermore, the spindle can only move vertically thanks to the
elongated hole shown in section "B" of the drawing.
This solution allows an optimal control of the geometry even when
large amounts of torque are introduced into the system.
The head is very accurate and reliable.
Spare Parts
- 2 x Blade Grip.
- 2 x Thrust Bearing
5x
10x4mm.
- 4 x Bearing
5x
10x4mm.
- 2 x Washer
7.5x
10x0.5mm.
- 2 x Button Head Socket Cap M4x6mm.
- 2 x Washer
5x
7x0.1mm.
Blade Grip
[H0513-S]
- 1 x Blade Grip Arm.
- 1 x Socket Head Cap Screw M2.5.x8mm.
Blade Grip Arm
[H0597-S]
Spindle Shaft
[H0596-S]
- 1 x Spindle Shaft.
- 1 x C Washer
5x
5x0.2mm.
ABOUT HPS3
For safety reasons we suggest to not exceed 3400 rpm.
In addition, we recommend using a smaller tail pulley in order to increase the tail rotor speed to counteract the additional
torque introduced by the 3rd rotor blade. You will find a 20T tail rotor pulley in the kit for this purpose.
TIPS:
Left Side
Right Side
* To remove the dampeners, you
can use a flathead screwdriver
through the hole as shown.
* Clock-wise, counter clock-wise thread
* By turning the linkages you can adjust
tracking. If tracking is adjusted correctly,
you’ll see the metal part line up around
in the center of the opening.
Detail B
SPARE PARTS
RECOMMENDATIONS
These parts should be used only with models SAB Goblin 380.
- 3 blade rotor heads require a much lower cyclic gain on flybarless systems.We recommend that you set your gain at least 30%
lower than the gain you normally use on your 2 blade rotor head helicopters.You can start increasing the gain after you
complete your first flight. Running too high of a gain can induce a violent oscillation that can potentially cause damage
to your helicopter in flight.
- Please follow all the instructions shown in the Goblin main manual.
In this manual please read Chapter 2, Important notes
- Use Loctite on all threads.
Page 2
HPS3 ROTOR HEAD
[
H0640-K
]
Specyfikacje produktu
| Marka: | SAB Heli Division |
| Kategoria: | Budowa modelu |
| Model: | Head HPS3 - H0640-K |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z SAB Heli Division Head HPS3 - H0640-K, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Budowa modelu SAB Heli Division
25 Września 2024
24 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
Instrukcje Budowa modelu
- Budowa modelu Lego
- Budowa modelu Voltcraft
- Budowa modelu Chicco
- Budowa modelu Revell
- Budowa modelu Playmobil
- Budowa modelu Viessmann
- Budowa modelu Carson
- Budowa modelu Heller
- Budowa modelu Trix
- Budowa modelu Reely
- Budowa modelu Tams Elektronik
- Budowa modelu BRIO
- Budowa modelu ISDT
- Budowa modelu Multiplex
- Budowa modelu Wilesco
- Budowa modelu Marklin
- Budowa modelu Kibri
- Budowa modelu Mega Bloks
- Budowa modelu KidKraft
- Budowa modelu Geomag
- Budowa modelu Robbe
- Budowa modelu LGB
- Budowa modelu Woodland Scenics
- Budowa modelu Snap Circuits
- Budowa modelu Pocher
- Budowa modelu Wiking
- Budowa modelu Siku
- Budowa modelu MBZ
- Budowa modelu FALLER
- Budowa modelu Seuthe
- Budowa modelu Metal Earth
- Budowa modelu E-Blox
- Budowa modelu Piko
- Budowa modelu Fleischmann
- Budowa modelu Roco
- Budowa modelu Proses
- Budowa modelu Brawa
- Budowa modelu NOCH
- Budowa modelu Massoth
- Budowa modelu Italeri
Najnowsze instrukcje dla Budowa modelu
14 Października 2024
9 Października 2024
Italeri Scania R730 V8 Streamline ‘‘Silver Griffin’’ Instrukcja
8 Października 2024
8 Października 2024
8 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024
5 Października 2024
5 Października 2024