Instrukcja obsługi RYOBI RWS1250-G
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla RYOBI RWS1250-G (5 stron) w kategorii piła. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/5
ORIGINAL INSTRUCTIONS
TRADUCTION DES INSTRUCTIONS ORIGINALES
ÜBERSETZUNG DER ORIGINALANLEITUNG
TRADUCCIÓN DE LAS INSTRUCCIONES ORIGINALES
TRADUZIONE DELLE ISTRUZIONI ORIGINALI
VERTALING VAN DE ORIGINELE INSTRUCTIES
TRADUÇÃO DAS INSTRUÇÕES ORIGINAIS
OVERSÆTTELSE AF DE ORIGINALE INSTRUKTIONER
ÖVERSÄTTNING AV DE URSPRUNGLIGA INSTRUKTIONERNA
ALKUPERÄISTEN OHJEIDEN SUOMENNOS
OVERSETTELSE AV DE ORIGINALE INSTRUKSJONENE
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
T UMACZENIE INSTRUKCJI ORYGINALNEJŁ
P EKLAD ORIGINÁLNÍCH POKYNŘ Ů
AZ EREDETI ÚTMUTATÓ FORDÍTÁSA
TRADUCEREA INSTRUC IUNILOR ORIGINALEŢ
TULKOTS NO ORI IN L S INSTRUKCIJASĢ Ā Ā
ORIGINALI INSTRUKCIJ VERTIMASŲ Ų
ORIGINAALJUHENDI TÕLGE
PRIJEVOD ORIGINALNIH UPUTA
PREVOD ORIGINALNIH NAVODIL
PREKLAD ORIGINÁLNYCH POKYNOV
ΜΕΤΆΦΡΑΣΗ ΠΡΩΤΌΤΥΠΩΝ ΟΔΗΓΙΏΝ ΤΩΝ
ORIJINAL TALIMATLARIN TERCÜMESI
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
EL
TR
RWS1600
RWS1400
RWS1250
si
English
1
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
EL
TR
SPECIAL SAFETY RULES
CUTTING PROCEDURES
DANGER
Keep hands away from cutting area and the blade.
Keep your second hand on auxiliary handle, or
motor housing. If both hands are holding the saw, they
cannot be cut by the blade.
■ Do not reach underneath the workpiece. The guard
cannot protect you from the blade below the workpiece.
■ Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
■ Never hold piece being cut in your hands or across
your leg. Secure the workpiece to a stable platform.
It is important to support the work properly to minimize
body exposure, blade binding, or loss of control.
■ Hold the power tool by insulated gripping surfaces
only, when performing an operation where the
cutting tool may contact hidden wiring or its own
cord. Contact with a “live” wire will also make exposed
metal parts of the power tool “live” and could give the
operator an electric shock.
■ When ripping, always use a rip fence or straight
edge guide. This improves the accuracy of cut and
reduces the chance of blade binding.
■ Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades that
do not match the mounting hardware of the saw will run
eccentrically, causing loss of control. Use only blades
specified in this manual, complying with EN 847-1.
■ Never use damaged or incorrect blade washers
or bolt. The blade washers and bolt were specially
designed for your saw, for optimum performance and
safety of operation.
KICKBACK CAUSES AND RELATED WARNINGS:
■ kickback is a sudden reaction to a pinched, bound or
misaligned saw blade, causing an uncontrolled saw to
lift up and out of the workpiece toward the operator;
■ when the blade is pinched or bound tightly by the kerf
closing down, the blade stalls and the motor reaction
drives the unit rapidly back toward the operator;
■ if the blade becomes twisted or misaligned in the cut,
the teeth at the back edge of the blade can dig into the
top surface of the wood causing the blade to climb out
of the kerf and jump back toward the operator.
Kickback is the result of saw misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
■ Maintain a firm grip with both hands on the saw
and position your arms to resist kickback forces.
Position your body to either side of the blade, but
not in line with the blade. Kickback could cause the
saw to jump backwards, but kickback forces can be
controlled by the operator, if proper precautions are
taken.
■ When blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the saw
motionless in the material until the blade comes
to a complete stop. Never attempt to remove the
saw from the work or pull the saw backward while
the blade is in motion or kickback may occur.
Investigate and take corrective actions to eliminate the
cause of blade binding.
■ When restarting a saw in the workpiece, centre the
saw blade in the kerf and check that saw teeth are
not engaged into the material. If saw blade is binding,
it may walk up or kickback from the workpiece as the
saw is restarted.
■ Support large panels to minimise the risk of blade
pinching and kickback. Large panels tend to sag
under their own weight. Supports must be placed under
the panel on both sides, near the line of cut and near
the edge of the panel.
■ Do not use dull or damaged blades. Unsharpened
or improperly set blades produce narrow kerf causing
excessive friction, blade binding and kickback.
■ Blade depth and bevel adjusting locking levers
must be tight and secure before making cut. If blade
adjustment shifts while cutting, it may cause binding
and kickback.
■ Use extra caution when sawing into existing walls
or other blind areas. The protruding blade may cut
objects that can cause kickback.
LOWER GUARD FUNCTION
■ Check lower guard for proper closing before each
use. Do not operate the saw if lower guard does not
move freely and close instantly. Never clamp or
tie the lower guard into the open position. If saw is
accidentally dropped, lower guard may be bent. Raise
the lower guard with the retracting handle and make
sure it moves freely and does not touch the blade or any
other part, in all angles and depths of cut.
■ Check the operation of the lower guard spring. If
the guard and the spring are not operating properly,
they must be serviced before use. Lower guard may
operate sluggishly due to damaged parts, gummy
deposits, or a build-up of debris.
■ Lower guard may be retracted manually only for
special cuts such as “plunge cuts” and “compound
cuts”. Raise lower guard by retracting handle and
as soon as blade enters the material, the lower
guard must be released. For all other sawing, the
lower guard should operate automatically.
■ Always observe that the lower guard is covering the
Specyfikacje produktu
| Marka: | RYOBI |
| Kategoria: | piła |
| Model: | RWS1250-G |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z RYOBI RWS1250-G, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje piła RYOBI
14 Września 2024
13 Września 2024
13 Września 2024
5 Września 2024
10 Lipca 2024
10 Lipca 2024
9 Lipca 2024
Instrukcje piła
- piła AEG
- piła Worx
- piła Milwaukee
- piła Stihl
- piła Bosch
- piła Parkside
- piła Festool
- piła Stanley
- piła Black & Decker
- piła Scheppach
- piła Proxxon
- piła Lider
- piła Hazet
- piła DeWalt
- piła Einhell
- piła Silverline
- piła Husqvarna
- piła Makita
- piła Ozito
- piła Fuxtec
- piła DEDRA
- piła Trotec
- piła Meec Tools
- piła Güde
- piła Texas
- piła Zipper
- piła Solo
- piła Ferrex
- piła McKenzie
- piła Ferm
- piła Hitachi
- piła Fieldmann
- piła PowerPlus
- piła Vonroc
- piła HiKOKI
- piła Workzone
- piła Masport
- piła Metabo
- piła Cocraft
- piła Snow Joe
- piła Yellow Garden Line
- piła Ideal
- piła Kinzo
- piła Gamma
- piła Kress
- piła Varo
- piła Batavia
- piła Protool
- piła Elu
- piła Lux Tools
- piła Triton
- piła Fleurelle
- piła Evolution
- piła Dual Saw
- piła Elektra Beckum
- piła Toolson
- piła Dexter Power
- piła Toledo
- piła Graule
- piła Exakt
- piła Mac Allister
Najnowsze instrukcje dla piła
15 Października 2024
15 Października 2024
6 Października 2024
5 Października 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024