Instrukcja obsługi Ruwido s 9 easytip


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ruwido s 9 easytip (30 stron) w kategorii Zdalne sterowanie. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/30
Index
D
I
F
E
P
NL
GB USER MANUAL 2 - 5
BEDIENUNGSANLEITUNG 6 - 9
ISTRUZIONI PER L’USO 10 - 13
MODE D’EMPLOI 14 - 17
MODO DE EMPLEO 18 - 21
MANUAL DE INSTRUÇÕES 22 - 25
GEBRUIKSAANWIJZING 26 - 29
Easy programming for the control of your TUNER
(RADIO)
To programme the remote control to operate your TUNER, proceed as
described for the CD PLAYER but using the key instead of the CD key.
Please ensure that you refer to the codes listed under the TUNER section and
not the CD PLAYER section.
Easy programming for the control of your TAPE
RECORDER (TAPE DECK)
To programme the remote control to operate your TAPE RECORDER, proceed
as described for the CD PLAYER but using the key instead of the CD key.
Please ensure that you refer to the codes listed under the TAPE section and not
the CD PLAYER section.
Easy programming for the control of your AMPLIFIER
To programme the remote control to operate your AMPLIFIER, proceed as
described for the CD PLAYER. Complete steps 1 to 10, using the key on
your remote control. Please ensure that you refer to the codes listed under the
AMPLIFIER section and not CD PLAYER section.
Code scan
If programming using the codes in the enclosed list failed to work then you
must next try the automatic code scan.
A. Ensure that the remote control is equipped with 2 new batteries (see step
one of easy programming procedure).
B. Switch on your TV SET. When using the automatic scan function for the
VCR, DVD, CD or TAPE, switch on your device, insert a video tape, DVD,
CD or tape cassette and put the unit into ‘Play mode’ i.e, the VCR tape etc
is running.
C. Press the key of your remote control for approx. 4 seconds until the
LED flashes twice.
D. After seeing the 2 flashes and within 5 seconds, enter the code .
After entering the code the LED will flash twice indicating that the code has
been accepted
E. Press and hold the key until your TV switches off. Please note that this
process might take up to 15 minutes. During the automatic scanning you
can remove your finger or change hands provided it is replaced within 8
seconds. If left off of the key for more than 8 seconds then the remote will
revert back to its normal mode. If your TV switches into Stand-By mode
during the automatic process then immediately remove your finger from the
key and then press and release the key until the LED flashes
twice, this will then store the code that the remote has found
F. In some cases during the automatic scanning search the remote control
might find several codes that appear to operate your TV etc, however, if
some of the buttons fail to work properly then it’s possible the remote has
found a partially compatible code. In such cases you will need to restart the
automatic scanning process (steps B. to F.) until a better code is found.
Please note that once the automatic process is restarted, the remote
continues from the last stored code and not at the beginning of code
database.
• To complete a code scan for the VCR, DVD, CD or TAPE, follow the
procedure above but use the key and not the key
• To complete a code scan for the TUNER, follow the procedure above but
use the key
2
TV
1
0
0
TV
AMP
TAPE
TUNER
3
UNIVERSAL REMOTE CONTROL
Thank you for purchasing this universal remote control. Before using the
remote you will need to insert 2 type "AAA" batteries (not included) in the
battery compartment ensuring that you follow the polarity shown on the inside.
You can now use your remote control to operate up to 9 different devices
(depending on the model) including a TV, video recorder, DVD player, satellite or
cable receiver, CD player, tuner (radio), tape recorder and amplifier. If your
remote control is equipped with an AUX key (not standard on all models) then
you can also use it to control a second TV set, video recorded, satellite receiver
and/or cable box, CD player, tuner, tape recorder or amplifier!
Easy programming for the control of your TV SET
1. Insert 2 new 1.5V alkaline batteries of type "AAA/LR03". Observe battery
polarity as indicated in the battery compartment.
2. Switch on your TV SET.
3. In the enclosed code list, find your TV brand or manufacturer (e.g. Sony).
4. Beside the manufacturer's name, you will find one or more 3-digit codes.
These codes must be entered into the remote to enable it to work with your
particular TV set.
5. Press the key on the remote control for approximately 4 seconds until
the LED flashes twice.
6. After seeing the 2 flashes and within 5 seconds, enter the 3-digit numerical
code from the list.
7. After entering the code the LED will flash twice indicating that the code has
been accepted.
8. Point the remote control towards your TV and press the key. If your TV
does not respond by going into Stand-By mode then repeat steps 3 to 8
and enter the next code in the list.
9. If your TV goes into Stand-By mode when the key pressed then your
remote control has found a compatible code. Next test all of the other
function buttons. If certain functions are not working correctly then restart
the process moving onto the next code number as this may well improve
the situation.
10. If the codes in the list fail to operate your TV then next move onto the
automatic code scan function (see below).
Easy programming for the control of your VIDEO
RECORDER
To programme the remote control to operate your VIDEO RECORDER, proceed
as described above for the television set. Complete steps 1 to 10 using the
key on your remote control. Please ensure that you refer to the codes
listed under the VIDEO RECORDER section and not the TV section.
Easy programming for the control of your SATELLITE
RECEIVER
To programme the remote control to operate your SATELLITE RECEIVER or
CABLE BOX, proceed as described for the television set. Complete steps 1 to
10 using the key on your remote control. Please ensure that you refer to
the codes listed under the SATELLITE section and not the TV section.
Easy programming for the control of your DVD PLAYER
To programme the remote control to operate your DVD PLAYER, proceed as
described for the television set. Complete steps 1 to 10 using the key on
your remote control. Please ensure that you refer to the codes listed under the
DVD section and not the TV section.
Easy programming for the control of your CD PLAYER
To programme the remote control to operate your CD PLAYER, proceed as
described for the television set. Complete steps 1 to 10 except you must first
press and release the key followed by holding down the key. Please
ensure that you refer to the codes listed under the CD section and not the TV
section.
SHIFT
DVD
SAT
VCR
TV
2
USER MANUAL
GB USER MANUAL
GB
Special functions of your remote control
Brightness / Colour / Contrast / etc.
Adjusting brightness / colour / contrast / bass / tremble / balance at your TV
set, using the universal remote control:
1. Ensure that your remote control is set to TV (press key).
2. Press the key.
3. Within 5 seconds, press
for brightness, for colour,
for contrast, for tremble,
for bass, for balance.
4. To adjust the settings use the and keys.
5. After 5 seconds, your remote control returns to standard mode for the
selection of channels.
OK key
• At TV level The basic settings of your TV SET are activated
• At TV level / menu Confirmation key for settings
• At VCR level Record button (press key twice)
• At SAT level Confirmation key for settings
• At DVD level Confirmation key for settings
• At TAPE level Record button (press key twice)
Please write down the 3-digit codes of your devices for future reference.
Depending on the remote control model, you might have to reprogram me
the universal control device after a battery change.
VOL-
VOL+
6
5
4
3
2
1
SHIFT
TV
5
Code scan for VCR, SAT, DVD, CD, TAPE, TUNER and
AMP
To complete a code scan for VCR, SAT, DVD, CD, TAPE, TUNER or AMP,
proceed as described for a TV code scan. Complete above steps A to G, using
keys
/ or , or
and / and / and or and respectively.
At step E,
for SAT and AMP, press the key;
for VCR, DVD, CD and TAPE, press the key, and
for TUNER, press key .
Finding out what code number you are using
If you have programmed your remote control by means of the automatic code
scan, or if you have forgoten the code you have stored then the following
procedure will replay the codes being used.
A. Press the key of your remote control for approx. 4 seconds until the
LED flashes twice.
B. Enter code , using the numerical keys. The LED flashes twice.
C. Press key and count the number of LED flashes. This number
corresponds to the first digit of the code.
D. Press key and count the number of LED flashes. This number
corresponds to the second digit of the code (if the digit is 0, the LED does
not flash).
E. Press key and count the number of LED flashes. This number
corresponds to the third digit of the code (if the digit is 0, the LED does not
flash).
F. Steps C, D and E can be repeated as often as necessary.
To read the currently used code for the control of a VCR, SAT, DVD/AUX, CD,
TAPE, TUNER or AMP device, proceed as described above for your TV SET.
Complete steps A to F, pressing the , , , , , or
key respectively.
Write down the code number as indicated by the LED.
Programming for AUX devices
If the remote you have purchased has a separate AUX key then this can be
used to operate a second TV set, video recorder, satellite receiver/cable box,
CD player, tape recorder, tuner or amplifier. To program your remote
control for a second device, proceed as follows:
1. Press the key of your remote control until the LED flashes twice.
2. Press
key for a second TV set,
key for a second video recorder,
key for a second satellite receiver or cable box,
keys and for a second CD player,
keys and for a second tape recorder,
keys and for a second tuner,
keys and for a second amplifier.
3. On the numerical keypad, enter a 3-digit code from the enclosed list.
4. The LED flashes twice, indicating that the code has been accepted.
AMP
SHIFT
TUNER
SHIFT
TAPE
SHIFT
SHIFT
SAT
VCR
TV
AUX
AMP
TUNER
TAPE
DVD
SAT
VCR
3
2
1
2
0
0
TV
2
AMP
SHIFT
TUNER
SHIFT
TAPE
SHIFT
SHIFT
DVD
SAT
VCR
4
TV
VCR
SAT
DVD/AUX
CD
TAPE
TUNER
AMPLIFIER
USER MANUAL
GB USER MANUAL
GB


Specyfikacje produktu

Marka: Ruwido
Kategoria: Zdalne sterowanie
Model: s 9 easytip

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ruwido s 9 easytip, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Zdalne sterowanie Ruwido

Instrukcje Zdalne sterowanie

Najnowsze instrukcje dla Zdalne sterowanie

Neewer

Neewer RT112 Instrukcja

9 Października 2024
Neewer

Neewer RT113 Instrukcja

9 Października 2024
Zalman

Zalman ZM-VE350 Instrukcja

9 Października 2024
Canon

Canon BG-R20 Instrukcja

9 Października 2024
Canon

Canon BG-R20EP Instrukcja

9 Października 2024
Mosconi

Mosconi DSP6T8 Instrukcja

8 Października 2024
Mosconi

Mosconi RC MINI Instrukcja

8 Października 2024
Ridem

Ridem CRC UNB Instrukcja

8 Października 2024
Ridem

Ridem CRC UNW Instrukcja

8 Października 2024
ORNO

ORNO OR-GB-458 Instrukcja

8 Października 2024