Instrukcja obsługi Ruwido 5in1

Ruwido pilot 5in1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ruwido 5in1 (13 stron) w kategorii pilot. Ta instrukcja była pomocna dla 17 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/13

I n d e x

GB USER MANUAL 2 - 5

BEDIENUNGSANLEITUNG 6 - 9

ISTRUZIONI PER L’USO 10 - 13

MODE D’EMPLOI 14 - 17

GEBRUIKSAANWIJZING 18 - 21

UNIVERSAL REMOTE CONTROL

Thank you for purchasing this universal remote control. Before using the remote you will need

to insert two type "CR2025" batteries (for all Linum models) or two AAA "LR03" batteries (for

AlveusLux 10 and 5 in 1 models) in the battery compartment ensuring that you follow the

polarity shown on the inside. You can now use your remote control to operate up to 10 different

devices including a TV, video recorder, DVD player, satellite or cable receiver, CD player, tuner

(radio), tape recorder and amplifier. If your remote control is equipped with an AUX key then

you can also use it to control a second TV set, video recorded, satellite receiver and/or cable

box, CD player, tuner, tape recorder or amplifier!

Easy programming for the control of your TV SET

1. Insert 2 new batteries of type "CR2025" or "AAA/LR03" (depending on your model).

Observe battery polarity as indicated in the battery compartment.

2. Switch on your TV SET.

3. In the enclosed code list, find your TV brand or manufacturer (e.g. Sony).

4. Beside the manufacturer's name, you will find one or more 3-digit codes. These codes

must be entered into the remote to enable it to work with your particular TV set.

5. Press the key on the remote control for approximately 4 seconds until the LED flashes

twice.

6. After seeing the 2 flashes and within 5 seconds, enter the 3-digit numerical code from the

list.

7. After entering the code the LED will flash twice indicating that the code has been accepted.

8. Point the remote control towards your TV and press the key. If your TV does not

respond by going into Stand-By mode then repeat steps 3 to 8 and enter the next code in

the list.

9. If your TV goes into Stand-By mode when the key pressed then your remote control

has found a compatible code. Next test all of the other function buttons. If certain functions

are not working correctly then restart the process moving onto the next code number as

this may well improve the situation.

10. If the codes in the list fail to operate your TV then next move onto the automatic code scan

function (see below).

Easy programming for the control of your VIDEO RECORDER

To programme the remote control to operate your VIDEO RECORDER, proceed as described

above for the television set. Complete steps 1 to 10 using the key on your remote control.

Please ensure that you refer to the codes listed under the VIDEO RECORDER section and not

the TV section.

Easy programming for the control of your SATELLITE RECEIVER

To programme the remote control to operate your SATELLITE RECEIVER or CABLE BOX,

proceed as described for the television set. Complete steps 1 to 10 using the key on your

remote control. Please ensure that you refer to the codes listed under the SATELLITE section

and not the TV section.

Easy programming for the control of your DVD PLAYER

To programme the remote control to operate your DVD PLAYER, proceed as described for the

television set. Complete steps 1 to 10 using the key on your remote control. Please ensure

that you refer to the codes listed under the DVD section and not the TV section.

DVD

SAT

VCR

USER MANUAL

USER M

Code scan for VCR, SAT, DVD, CD, TAPE, TUNER and AMP

To complete a code scan for VCR, SAT, DVD, CD, TAPE, TUNER or AMP, proceed as described

for a TV code scan. Complete above steps A to G, using keys / or , or

and / and / and or and respectively.

At step E,

for SAT and AMP, press the key;

for VCR, DVD, CD and TAPE, press the key, and

for TUNER, press key .

Finding out what code number you are using

If you have programmed your remote control by means of the automatic code scan, or if you

have forgot the code you have stored then the following procedure will replay the codes being

used.

A. Press the key of your remote control for approx. 4 seconds until the LED flashes twice.

B. Enter code , using the numerical keys. The LED flashes twice.

C. Press key and count the number of LED flashes. This number corresponds to the first

digit of the code.

D. Press key and count the number of LED flashes. This number corresponds to the

second digit of the code (if the digit is 0, the LED does not flash).

E. Press key and count the number of LED flashes. This number corresponds to the third

digit of the code (if the digit is 0, the LED does not flash).

F. Steps C, D and E can be repeated as often as necessary.

To read the currently used code for the control of a VCR, SAT, DVD/AUX, CD, TAPE, TUNER or

AMP device, proceed as described above for your TV SET. Complete steps A to F, pressing the

, , , , , or key respectively.

Write down the code number as indicated by the LED.

Programming for AUX devices

Depending on the model, you can use your universal remote control to operate a second TV

set, video recorder, satellite receiver/cable box, CD player, tape recorder, tuner or amplifier. To

program your remote control for a second device, proceed as follows:

1. Press the key of your remote control until the LED flashes twice.

2. Press

key for a second TV set,

key for a second video recorder,

key for a second satellite receiver or cable box,

keys and for a second CD player,

keys and for a second tape recorder,

keys and for a second tuner,

keys and for a second amplifier.

3. On the numerical keypad, enter a 3-digit code from the enclosed list.

4. The LED flashes twice, indicating that the code has been accepted.

AMP

SHIFT

TUNER

SHIFT

TAPE

SHIFT

SAT

VCR

AUX

AMP

TUNER

TAPE

DVD

SAT

VCR

AMP

SHIFT

TUNER

SHIFT

TAPE

SHIFT

DVD

SAT

VCR

USER MANUAL

USER M

Specyfikacje produktu

Marka:	Ruwido
Kategoria:	pilot
Model:	5in1
Kolor produktu:	Czarny
Wbudowany wyłącznik:	Tak
Wbudowany wyświetlacz:	Nie
Wysokość produktu:	22 mm
Szerokość produktu:	43 mm
Głębokość produktu:	200 mm
Waga produktu:	81 g
Rodzaj baterii:	AAA
Diody LED:	Tak
Liczba baterii:	2
Ładowanie akumulatora:	Nie
Baterie w zestawie:	Tak
Standardowe rozwiązania komunikacyjne:	Podczerwień
Maksymalny zasięg:	- m
Sposób wprowadzania danych:	Naciśnij przyciski
Podświetlane przyciski:	DVD/Blu-ray, TV, VCR
Ilość obsługiwanych urządzeń:	5