Instrukcja obsługi Roland MDS-50K

Roland Nie skategoryzowane MDS-50K

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Roland MDS-50K (1 stron) w kategorii Nie skategoryzowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/1
Main Specications
Roland MDS-50K: Drum Stand
Required space
for setup
1,350 (W) x 1,050 (D) x 1,100 (H) mm, 53-3/16 (W) x 41-3/8 (D) x 43-5/16 (H) inches
(drum stand only)
1,500 (W) x 1,300 (D) x 1,250 (H) mm, 59-1/16 (W) x 51-3/16 (D) x 49-1/4 (H) inches
(including sound module, kick pad, cymbals, and drum throne)
Tube diameter Stand: 38.1 mm, 1-1/2 inches
Pad arm/Cymbal arm: 22.2 mm, 7/8 inches
Weight 14.5 kg, 32 lbs (including pad mounts and cymbal mounts)
* This document explains the specications of the product at the time that the document was issued. For
the latest information, refer to the Roland website.
Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” After reading, keep the document(s)
where it will be available for immediate reference.
Check the Included Items
After opening the package, check that all of the included items are
present. If anything is missing, contact your dealer.
Stand
• Cymbal mount x 3 (with stand)
* Two of the cymbal mount rods are in a separate box.
• Pad mount x 3 (with stand)
• Connection cables (with stand)
• Sound module mounting plate
Drum key
Cable clip x 6
Cable tie x 3
* When shipped from the factory, these are wrapped around the
pipes to bundle the connection cables.
Owner’s Manual (this leaet)
Setting Up the Stand
1. Loosen hand knobs “A” (two locations) and spread open the left and right legs of the stand
as shown in the illustration (Fig. 2).
Fig. 2
2. Attach cymbal mount rods as shown in the illustration (Fig. 1).
3. Adjust pad mounts “B” (three locations) as shown in the illustration (Fig. 3).
Fig. 3
1. Loosen the bolt using the drum key, then
remove the ball clamp.
2. Position the rod in the upright position, then
reattach the ball clamp.
Bolt
Rod
Ball clamp
4. Adjust cymbal mounts “C” (three locations) as shown in the illustration (Fig. 1).
5. If the stand wobbles, loosen hand knobs “D” (two locations) and adjust the height.
* Do NOT loosen any bolts other than hand knobs except when changing the parts or cables
for repairing.
Caution in Setting Up the Stand
5The tip of the mount is sharp. Handle it with care.
5When setting up or storing the stand, be careful not to pinch the ngers and the connection
cables you use to handle the stand.
5Regarding the way of mounting a sound module, pads, or cymbals, please refer to the owner’s
manual supplied with them.
5Do not open the stand wider than 135 degrees outward.
Be sure the two pipes at the ends tare no more than 1.3
meters apart. Doing so can damage the cables inside the
stand or cause the stand to fall over.
5Never pull on any cables with excessive force.
5There are labels on the ends of the cables allowing easy
connection to your sound module. For the details on connections, refer to the owner’s manual
that came with your sound module.
The names on the labels correspond to trigger input jack names as follows.
Label KIK T1 T2 T3 T4 HH HHC
Jack KICK TOM 1 TOM 2 TOM 3 TOM 4 HI-HAT HH CTRL
Label CR1 CR2 AX1
Jack CRASH1 CRASH2 AUX 1
* SNARE/RIDE/BELL/TOM 2 connection cables are not included. Please obtain them
separately.
* When connecting to a V-pad or V-cymbal that is equipped with a DIGITAL TRIGGER OUT
port, use the connection cable included with that product.
5Use the cable clips as shown in the illustration, to secure
the cables.
5We recommend using an optional Roland drum mat
(TDM series) to prevent scarring or discoloration of
ooring by the rubber feet of the stand.
1.3 m
(51-3/16”)
135˚ 135˚
View of stand when spread open
Cable clip
Cable
English
Owner’s Manual Copyright © 2016 ROLAND CORPORATION
IMPORTANT NOTES
USING THE UNIT SAFELY
WARNING
Do not disassemble or modify by yourself
Do not carry out anything
unless you are instructed to
do so in the owner’s manual.
Otherwise, you risk causing
malfunction.
Do not repair or replace parts by yourself
Refer all servicing to
your retailer, the nearest
Roland Service Center,
or an authorized Roland
distributor, as listed on the
“Information.”
Do not use or store in the following types
of locations
• Subject to temperature
extremes (e.g., direct
sunlight in an enclosed
vehicle, near a heating
duct, on top of heat-
generating equipment);
or are
• Damp (e.g., baths, washrooms, on
wet oors); or are
• Exposed to steam or smoke; or are
• Subject to salt exposure; or are
• Exposed to rain; or are
• Dusty or sandy; or are
• Subject to high levels of vibration
and shakiness; or are
• Placed in a poorly ventilated
location.
Do not place in an unstable location
Otherwise, you risk injury
as the result of the unit
toppling over or dropping
down.
WARNING
Be cautious to protect children from
injury
Always make sure that an
adult is on hand to provide
supervision and guidance
when using the unit in
places where children are present, or
when a child will be using the unit.
Do not drop or subject to strong impact
Otherwise, you risk causing
damage or malfunction.
CAUTION
Use only stand manufactured by Roland
This stand for use only with
specic Roland musical
instruments. See apparatus
instructions. Use with other
models is capable of resulting in
instability causing possible injury.
Evaluate safety issues before using stands
Even if you observe the
cautions given in the
owner’s manual, certain
types of handling may allow
cause the stand to overturn. Please
be mindful of any safety issues before
using this product.
Route all power cords and cables in such a
way as to prevent them from getting
entangled
Injury could result if
someone were to trip on a
cable and cause the unit to
fall or topple.
CAUTION
Avoid climbing on top of the unit, or
placing heavy objects on it
Otherwise, you risk injury
as the result of the unit
toppling over or dropping
down.
Disconnect all cords/cables before
moving the unit
Damage or malfunction
may result if you fail to
disconnect all cables before
moving the unit.
Take care so as not to get ngers pinched
When setting up or storing
the stand, be careful not to
pinch the ngers you use
to handle the stand. An
adult should always be in charge of
handling these items.
Keep small items out of the reach of
children
To prevent accidental
ingestion of the parts listed
below, always keep them
out of the reach of small
children.
Included Parts:
• Screws
Placement
• Do not allow lighting devices that
normally are used while their light
source is very close to the unit
(such as a piano light), or powerful
spotlights to shine upon the same
area of the unit for extended
periods of time. Excessive heat
can deform or discolor the unit.
• Do not paste stickers, decals, or
the like to this instrument. Peeling
such matter o the instrument
may damage the exterior nish.
• Depending on the material and
temperature of the surface on
which you place the unit, its
rubber feet may discolor or mar
the surface.
Maintenance
• Never use benzine, thinners,
alcohol or solvents of any
kind, to avoid the possibility of
discoloration and/or deformation.
Additional Precautions
• When disconnecting all cables,
grasp the connector itself—never
pull on the cable. This way you will
avoid causing shorts, or damage
to the cable’s internal elements.
Trademarks
• Roland and V-Drums are either
registered trademarks or
trademarks of Roland Corporation
in the United States and/or other
countries.
• Company names and product
names appearing in this
document are registered
trademarks or trademarks of their
respective owners.
A: Hand knobs
D: Hand knobs
C: Cymbal mounts
B: Pad mount
Sound module
mounting plate
Fig. 1 Fully assembled view
Rod B: Pad mounts
C: Cymbal mount
Rod

Specyfikacje produktu

Marka: Roland
Kategoria: Nie skategoryzowane
Model: MDS-50K

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Roland MDS-50K, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Nie skategoryzowane Roland

Roland

Roland MDS-50K Instrukcja

3 Kwietnia 2025
Roland

Roland CB-76RL Instrukcja

3 Kwietnia 2025
Roland

Roland OP-RMP12 Instrukcja

3 Kwietnia 2025
Roland

Roland RH-L20 Instrukcja

3 Kwietnia 2025
Roland

Roland M-UF1G Instrukcja

3 Kwietnia 2025
Roland

Roland CB-88RL Instrukcja

3 Kwietnia 2025
Roland

Roland 7X7-TR8 Instrukcja

3 Kwietnia 2025
Roland

Roland CB-CS1 Instrukcja

2 Kwietnia 2025
Roland

Roland CB-MCC1 Instrukcja

2 Kwietnia 2025
Roland

Roland CB-HPD Instrukcja

2 Kwietnia 2025

Instrukcje Nie skategoryzowane

Najnowsze instrukcje dla Nie skategoryzowane

Spin Master

Spin Master 6026397 Instrukcja

3 Kwietnia 2025
EnGenius

EnGenius EPA5006HAT Instrukcja

3 Kwietnia 2025
IFM

IFM PE2599 Instrukcja

3 Kwietnia 2025
IFM

IFM RU6035 Instrukcja

3 Kwietnia 2025
Bestway

Bestway 9102S Instrukcja

3 Kwietnia 2025
Bestway

Bestway 9102T Instrukcja

3 Kwietnia 2025
Bestway

Bestway 21177 Instrukcja

3 Kwietnia 2025
Bestway

Bestway 21178 Instrukcja

3 Kwietnia 2025
Axor

Axor Starck 12456341 Instrukcja

3 Kwietnia 2025
Ruggard

Ruggard GTUV-SG Instrukcja

3 Kwietnia 2025