Instrukcja obsługi Roberts CD9959

Roberts Odtwarzacze/nagrywarki CD CD9959

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Roberts CD9959 (3 stron) w kategorii Odtwarzacze/nagrywarki CD. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

11 12 13

CD radio, mains lead, quick start guide and safety/warranty leaet.

Features

continued overleaf...

STEP 1 - Plug in & play FM radio STEP 2 - Play MW radio

What is in the Box?

B - Switch on your CD radio

C - Play FM radio

Play MW radio

A - Connect to the mains

• MW / FM stereo wavebands

• 20 track programmable CD

• CD repeat play

• Deep bass boost 1 Place your CD radio on a at surface.

2 Plug the mains lead into the mains power

socket (located towards the rear of the

unit) ensuring that the plug is pushed fully

into the socket.

3 Plug the other end of the mains lead into a

wall socket and switch on the socket.

1 Carefully, fully extend the telescopic aerial.

2 Switch on your CD radio by sliding the switch to the Function

‘Radio’ position. The will light.On indicator

• If you wish to switch off your CD radio, slide the switch Function

to the ‘Off’ position. The will go out.On indicator

1 Slide the switch to the Waveband ‘FM’ position.

2 Rotate the controlTuning to tune to the desired station. The

station frequency is indicated in the dial scale.

3 Rotate the Volume control to select the required level.

4 To receive stereo broadcasts set the FM Mode switch (located on

the right hand side of your CD radio) to the ‘STEREO’ position.

The FM stereo indicator will light.

5 If the station being received is weak some hiss may be audible, to

reduce the hiss set the switch to the FM Mode ‘MONO’ position

to return to mono operation.

6 Press the Deep bass boost button to activate the bass boost.

Press the button again to deactivate bass boost.

• It is recommended that the FM band be used wherever possible

as better results in terms of quality and freedom from interference

will usually be obtained than on the MW band.

1 Switch on your CD radio by sliding the switch Function

to the ‘Radio’ position. The will light.On indicator

2 Slide the switch to the Waveband ‘MW’ position.

3 Rotate the controlTuning to tune to the desired station.

The station frequency is indicated in the dial scale.

For MW reception there is a built in ferrite aerial. Rotate

the CD radio to the position giving best reception.

4 Rotate the Volume control to select the required level.

5 Press the button to activate the bass Deep bass boost

boost. Press the button again to deactivate bass boost.

6 To switch off your CD radio, slide the Function switch to

the ‘Off’ position. The will go out.On indicator

• It is recommended that the FM band be used wherever

possible as better results in terms of quality and freedom

from interference will usually be obtained than on the MW

band.

Headphone socket1

Deep bass boost button2

Volume control3

Repeat button4

Stop button5

Play / Pause button6

Previous track button7

Next track button8

9 Program button

10 On indicator

11 Repeat indicator

12 LED display

13 Play / Pause indicator

14 Program indicator

15 Open / close button

16 Telescopic aerial

17 Handle

18 Dial scale

19 Tuning control

20 Function switch

21 Waveband switch

22 FM Stereo indicator

23 Loudspeakers x 2

24 Mains power socket

25 FM mode switch

26 Battery compartment (underneath)

Controls

• Dial tuning system

• Headphone socket

• AC mains socket

• Batteries 6 x LR14 / C size (not included)

FM MODE

MONO STEREO

23 23

24 25

FM MODE

MONO STEREO

Please read the safety leaet provided before connecting your CD radio to the mains.

STEP 3 - Play CD-R / CD-RW discs

Use only Digital Audio CDs which have the symbol.

Never write on a CD or attach any sticker to the CD. Always hold the

CD at the edge and store it in its box after use with the label facing up.

To remove dust and dirt, breathe on the CD and wipe it with a soft,

lint-free cloth in a straight line from the centre towards the edge.

Cleaning agents may damage the CD.

Do not expose the CD to rain, moisture, sand, or to excessive heat.

(e.g. from heating equipment or in motor cars parked in the sun).

Your CD radio can playback CD-DA format audio CD-R/CD-RW discs that have been nalised* upon

completion of recording.

Your CD radio may fail to playback some CD-R/CD-RW discs due to poor recording of the

CD-R/CD-RW disc.

*Finalising enables a CD-R/CD-RW disc to playback on audio CD players such as your CD radio.

Note: If the unit is in the CD stop mode position for more than 15 minutes it will automatically switch to

the standby mode. The operation indicator and the display will go off in such a case. To use the unit again

slide the function switch to ‘Off’ for a few seconds and then back to the CD setting.

For operation of your CD radio please see overleaf.

CD-R / CD-RW discs

ROBERTS RADIO LIMITED

www.robertsradio.com

Step 3 cont. - Play CD / CD-RW discs Other information

Specications

Issue 1a

2020-12-11

Battery operation

B - Playing a CD

Power requirements

Mains 230V 50Hz only

Batteries 6 x LR14 / C size (not included)

Battery life Up to 16 hours depending on operating mode.

Circuit features

Headphone socket 3.5mm dia.

Aerial system FM Telescopic aerial

MW Built-in Ferrite aerial

Frequency coverage FM 87-108.5MHz, MW 513 - 1629kHz

Product markings

This symbol indicates AC voltage.

This symbol indicates DC voltage.

The name plate is located on the underside of the unit.

The company reserves the right to amend the specication without notice.

Headphone socket

A 3.5mm is provided for use with headphones. Inserting a Headphone socket

plug automatically mutes the internal loudspeakers.

Please be aware that the sensitivity of headphones can vary widely. We therefore

recommend setting the volume to a low level before connecting headphones.

Stereo CD radio

Please read this guide and the safety/warranty leaet before use

A - Inserting a CD

1 Set the to Function switch ‘CD’. The will light up and ‘--’ will ash on the display.On indicator

2 To open the CD compartment, push the Open / Close CD door. button on the

3 Press the CD onto the spindle until it clicks into place. Close the . The CD player will scan the CD door

contents of the CD and the total number of tracks will appear on the display.

4 If the switch is set to and a CD is not inserted the display will show Function ‘CD’ ‘no’.

1 Press the will light up and the display Play / Pause Play / Pause indicator button to start playback. The

will show the track number.

2 Set the Volume control Deep bass boost to the required setting. Press the button to activate the Bass

boost system if desired.

3 To pause playback press the button. The track number and the Play / Pause Play / Pause indicator will

ash. To resume playback press the button again.Play / Pause

4 To stop playback, press the button. The total number of tracks will appear on the display.Stop

5 To take out the CD, press the button on the CD door to open the door. Open / Close Note: The CD door

should only be opened when the CD is in Stop mode.

C - Selecting a track

1 Whilst the CD is playing, press either the Next or Previous track buttons to change to the desired track.

2 You can also skip tracks when the player is in stop mode. Skip to the desired track using the Next or

Previous track buttons. Press and hold the button to make the track numbers cycle, release the button

when the desired track number is displayed.

3 Press the Play / Pause button to play the selected track.

4 Whilst the CD is playing, press and hold down either the orNext Previous track buttons.

5 Release the button when the desired part of the track is reached.

CD Repeat mode

1 Whilst the CD is playing press the Repeat button once to repeat the current track. The Repeat indicator

will ash.

2 Press the Repeat Repeat indicator button again to repeat all tracks on the CD. The will light up.

3 Press the Repeat button again to return to normal play. The Repeat indicator will switch off.

Programmed play

Editing a programme

By programming the player you can play up to 20 tracks in any desired order.

1 Whilst the CD is in Stop mode, press the Program button. The display will ash ‘01’ once before ashing

‘00’. The will ash.Program indicator

2 Select the rst track using the Next or Previous track buttons. The track number will ash on the display.

Store this track by pressing the Program button. The display will ash the next counter number (‘02’) once

before ashing .‘00’

3 Repeat the above steps until you have completed your program (maximum 20 tracks). Press the Play/

Pause button to commence play of the selected tracks.

4 To stop the program press the button. The display will show the total number of tracks. To resume Stop

program play press the Program button, the display will ash the program counter number (‘03’) once

before ashing the programmed track number.

1 Whilst the CD is in Stop mode, repeatedly press the button to step through the tracks programmed Program

until you nd the desired counter number. The display will ash the counter number (‘03’) once before

ashing ‘00’. The will ash.Program indicator

2 Select a new track using the Next or Previous track buttons. The track number will ash on the display.

Store this track by pressing the Program button. The display will ash the selected track number. The new

track has been stored in the program. Press to play the revised program tracks.Play/Pause

Erase a programme

1 Whilst the CD is in Stop mode, open the CD door to erase the programme. Programmes are also erased

by changing position of the Function switch to the ‘Off’ or ‘Radio’ position.

Check a programme

1 Whilst the CD is in Stop mode, repeatedly press the Program button to step through the tracks programmed.

The display will ash each programmed track number sequence.

Please read the safety leaet provided before using batteries.

1 Slide the battery cover catch in the direction of the arrow. Open the battery

cover.

2 Fit six LR14 (C size) batteries into the spaces in the compartment. Take care

to ensure all batteries are inserted with the correct polarity as shown on the

outside of the battery compartment. Replace the battery cover.

3 Reduced power, distortion and a 'stuttering' sound are all signs that the batteries

may need replacing. If the unit is not to be used for any extended period of

time, it is recommended that the batteries are removed.

We would recommend for economy that the CD9959 is used on the mains

whenever possible with battery operation for occasional or stand-by use only.

IMPORTANT: Danger of explosion if batteries are incorrectly replaced. Replace

batteries only with the same or equivalent type.

CLASS 1 LASER PRODUCT means that the laser's construction makes it inherently safe

so that the legally prescribed maximum permissible radiation values can never be exceeded.

Caution: Using any equipment or devices other than those described and specied in these operating

instructions, or tampering with the unit in any way, can result in dangerous exposure to radiation.

OPEN

CD9959

Specyfikacje produktu

Marka:	Roberts
Kategoria:	Odtwarzacze/nagrywarki CD
Model:	CD9959
Kolor produktu:	Biały
Rodzaj zasilania:	AC, Battery
Typ wyświetlacza:	LED
Wysokość produktu:	137 mm
Szerokość produktu:	245 mm
Głębokość produktu:	245 mm
Waga produktu:	1790 g
Szerokość opakowania:	283 mm
Wysokość opakowania:	170 mm
Głębokość opakowania:	278 mm
Ilość:	1
Wbudowane głośniki:	Tak
Wyjścia słuchawkowe:	1
Wtyk słuchawek:	3,5 mm
Kraj pochodzenia:	Chiny
Obsługiwane formaty audio:	MP3, WMA
Skrócona instrukcja obsługi:	Tak
Zakresy tunera:	FM, MW
Karta gwarancyjna:	Tak
Waga wraz z opakowaniem:	2355 g
Liczba baterii:	6
Baterie w zestawie:	Nie
Przewód zasilający dołączony:	Tak
Kod produktu celnego (TARIC):	8527130000
Ilość wbudowanych glosników:	2
Typ napędu:	Przenośny odtwarzacz CD
Wymagane baterie:	Tak
Pasmo FM:	87 - 108.5 MHz
Czas pracy na zasilaniu akumulatorowym:	16 h
Zmieniarka CD:	Tak
Odtwarzacz mp3:	Tak
Typ anteny:	Zewnętrzny
Pauza:	Tak
Funkcja programowania:	Tak