Instrukcja obsługi Ring RBGDC200

Ring kamera samochodowa RBGDC200

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ring RBGDC200 (5 stron) w kategorii kamera samochodowa. Ta instrukcja była pomocna dla 33 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/5

Dash Camera Troubleshoong Guide

Page | 1 Rev 1

Recording Problems

1. Camera stops recording for no reason

For DC10/50 models, check if Moon Detecon feature is switched on. In order to save space on smaller

SD cards this feature will stop recording whenever no moon is detected in front of the camera. When

movement is detected the camera will commence recording again. For larger SD cards this feature is not

required.

To turn this feature o select:-

MENU > Video > Moon Detecon > O

DC10/50

2. Screen goes blank during recording

Check if the Backlight or LCD Power Save funcon is switched on. This feature will switch o the LCD ‘ ’ ‘ ’

screen aer a selected me in order to reduce distracon at night. This may give the impression

recording has stopped but it will sll be recording in the background.

To turn this feature o select:-

For DC10/50 models - MENU > Setup > Backlight > O

For DC200 model MENU > General Setngs > LCD Power Save –

DC10/50 DC200

3. Camera does not start recording aer ignion switched on

This can happen if the internal baery is heavily discharged. If the camera has not been used for some

me and the internal baery is fully discharged, it may take a few minutes before there is sucient

energy from the power adapter to charge the baery and power the dash camera

4 Recording is intermient .

4.1 Check SD card speed

Check the SD card being used has a speed of at least Class 6 (preferably Class10). The speed of the card

is indicated by a number inside a circle like below. If the SD card is not fast enough recording may be

intermient and les may become corrupted, causing playback problems.

Dash Camera Troubleshoong Guide

Page | 2 Rev 1

4.2 Check SD card is not fake

There are some fake SD cards on the market, which may not perform to their specied speed and cause

recording problems, especially when recording at Full HD resoluon. If you wish to check the speed of

an SD card there are programs available such as which can conrm the data transfer rate.

HD Tune

The table below shows expected transfer rates for each class of SD card. Highlighted in red are speeds

for the Class6 & Class10 cards recommended for use with Ring dash cameras

4.3 Check SD card is compable with camera

Check the SD card being used is not the UHS - Ultra High Speed type (indicated by a number inside a ‘U’),

as these may not be compable with the current Ring dash cameras.

4.4 Check power supply

Check the 12V power adapter is securely ed into the car power socket and the LED is always

illuminated whilst the engine is switched on. If the LED ickers or goes out during use, then the power

adapter may not be securely ed into the socket, which will cause the camera to power down.

Check the fuse in the end of the adapter is not blo wn

Dash Camera Troubleshoong Guide

Page | 3 Rev 1

Check the cable for damage, which may have caused the fuse to blow

4.5 Check 12V power socket on Stop/Start vehicles

If you have a stop/start vehicle, check that the 12V power socket does not power down when the

vehicle enters stop/start mode. If this happens the dash camera will also switch o. In this case the hard

wire kit (Part: RBGDCHK) can be used to connect directly to the vehicle fuse box

5. Error message is displayed

5.1 ‘Card Full’ message appears on screen

If the loop recording funcon is set to O this message will be displayed when the card becomes full. ‘ ’

To avoid this problem set the length of each video clip to 3 or 5 minutes using the procedure below. This

will ensure ‘loop mode’ is acvated, which will automacally delete the oldest les when the card

becomes full.

For DC10/50 model – MENU > Video > Loop Recording

For DC200 model MENU > Movie Mode > Move Clip Time –

5 Card Error message appears on screen .2 ‘ ’

The SD card has become corrupted. Remove the useful les then re-format the card using the camera

menu opon

For DC10/50 models MENU > Setup > Format –

For DC200 model MENU > General Setngs > Format SD- –Card

File transfer problems

1. Error when connecng via USB

If the error similar to below appears then the SD card may not have been correctly formaed.

Re-format the SD card using procedure below depending on camera model

For DC10/50 models MENU > Setup > Format –

For DC200 model MENU > General Setngs > Format SD- –Card

Specyfikacje produktu

Marka:	Ring
Kategoria:	kamera samochodowa
Model:	RBGDC200
Kolor produktu:	Czarny
Rodzaj zasilania:	Bateria
Wbudowany wyświetlacz:	Tak
Automatyczne wyłączanie zasilania:	Tak
Wysokość produktu:	23 mm
Szerokość produktu:	40 mm
Głębokość produktu:	99 mm
Waga produktu:	95.9 g
Technologia łączności:	Przewodowa
Rozdzielczość głównego aparatu/kamery:	1920 x 1080 px
Liczba kamer:	1
GPS:	Tak
Zasięg obiektywu:	2 - 2
Napięcie operacyjne wejścia (maksymalne):	24 V
Pojemność baterii:	110 mAh
Technologia baterii:	Litowo-polimerowy (LiPo)
Długość przekątnej ekranu:	2 "
Obsługiwane typy kart pamięci:	SD
Maksymalny rozmiar karty pamięci:	32 GB
Nagrywanie dźwięku:	Tak
Liczba portów Mini-USB:	1
Maksymalna liczba klatek na sekundę:	30 fps
Przewody:	DC, Mini-USB, USB
Ilość portów HDMI:	1
Wbudowane nośniki pamięci masowej:	Nie
Dołączony wyświetlacz:	Tak
Kąt widzenia głównej kamery:	140 °
Sensor G-shock:	Tak
Rozdzielczość zdjęcia:	1920 x 1080 px
Rozdzielczość czujnika głównej kamery:	14 MP