Instrukcja obsługi Radial Engineering Switchbone JX-2

Radial Engineering Nie skategoryzowane Switchbone JX-2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Radial Engineering Switchbone JX-2 (6 stron) w kategorii Nie skategoryzowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
®
™
CAUTION: You must read this manual
before connecting this device. There is a
strict procedure to follow especially when
connecting older vintage ampliers that are
not equipped with safety grounds.
RADIAL ENGINEERING
3 YEAR TRANSFERABLE WARRANTY
Radial Engineering Ltd. warrants this product to be free from defects
in material and workmanship and will remedy any such defects free
of charge according to the terms of this warranty. Radial Engineering
will repair or replace at its option any defective component(s) of this
product, excluding the nish, the tube, the footswitch (tubes and
footswitches are warranted for 90 days) and wear and tear from
normal use, for a period of three (3) years from the original date of
purchase. In the event that a particular product is no longer available,
Radial Engineering reserves the right to replace the product with
a similar product of equal or greater value. In the unlikely event
that a defect is uncovered, please call 1-800-942-1001 or email
service@radialeng.com to obtain an RA number (Return Authorization
number) before the 3 year warranty period expires. Once you have
obtained an RA number you must return the product, freight prepaid,
within fteen (15) days after the date the RA number is issued. To
make a request or claim under this limited warranty, the product must
be returned prepaid in the original shipping container (or equivalent)
to Radial Engineering or to an authorized repair centre and you must
assume the risk of loss or damage. A copy of the original invoice
showing date of purchase and the dealer name must accompany any
request for work to be performed under this limited warranty. This
limited warranty shall not apply if the product has been damaged due
to abuse, misuse, misapplication, accident or as a result of service or
modication by any other than an authorized repair centre.
THERE ARE NO EXPRESSED WARRANTIES OTHER THAN
THOSE ON THE FACE HEREOF AND DESCRIBED ABOVE. NO
WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING
BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
SHALL EXTEND BEYOND THE RESPECTIVE WARRANTY PERIOD
DESCRIBED ABOVE OF THREE YEARS. RADIAL ENGINEERING
SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS ARISING
FROM THE USE OF THIS PRODUCT. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS, WHICH MAY VARY DEPENDING ON WHERE YOU LIVE
AND WHERE THE PRODUCT WAS PURCHASED.
www.tonebone.com
www.radialeng.com
1588 Kebet Way, Port Coquitlam, BC V3C 5M5
tel: 604-942-1001 fax: 604-942-1010
email:info@radialeng.com
JX-2 Users Guide v2.0 - Feb. 2010 Part #: R870 1030 00
Specications and appearance subject to change without notice. Copyright
© 2010 Radial Engineering Ltd.
www.radialeng.com
www.radialeng.com
True to the Music
Radial Engineering
1588 Kebet Way, Port Coquitlam BC V3C 5M5
tel: 604-942-1001 • fax: 604-942-1010
email: info@radialeng.com • web: www.radialeng.com
JX•2 Switchbone
Users Guide
®
™
INDEX PAGE
Caution ............................................................................... 1
Introduction ......................................................................... 3
Concept ............................................................................. 3
Grounding .......................................................................... 4
Feature set 5 ........................................................................
Getting started 6 ....................................................................
Switch LED indicators 7 ........................................................
Drag™ Control 8 ...................................................................
Boost Circuit 8 .......................................................................
Set-ups ............................................................................... 9
Questions & Answers ............................... Inside back cover
Warranty .................................................Outside back cover
Greetings from Radial! You are now an official Bonehead!
The following manual has been written to assist you with your new Radial
JX2 Switchbone. Please take the time to read it so you can take maximum
advantage of all the features that have been designed into this marvelous
device and are familiar with the safety procedures.
Should you have any questions on the Switchbone, please visit our web
site www.tonebone.com for up-to-date information. Occasionally, take
a few minutes to peruse the questions and answers section for helpful
tips that will surely emerge as more and more Switchbones are sold. If
by chance you have a question that is not covered in this manual or on
our web site, please feel free to contact Radial at info@radialeng.com
and we will do our very best to get you an answer quickly. These ques-
tions are often the source for more FAQs on our site and serve to help
other Boneheads.
In the interim, enjoy! The Switchbone has been developed to help
you make music more fun and hopefully, enhance your creative spirit.
Now get out there and re up that double stack!
JX•2 Switchbone
User Guide
™
<<<<<<< CAUTION >>>>>>>
Please read before connecting
electronic devices to your JX2!
Caution must be used when connecting electronic equipment to
the JX2 switchbone. The JX2 bridges all electronic equipment
connected to it so faulty wiring or incorrect grounding of any of
the equipment may cause a shock hazard to be present and/or
damage to the JX2 or other connected equipment. Because
grounding schemes differ between manufacturers, it is important
to check for correct polarity, in particular with older ampliers using
2-prong unprotected A/C cords. If the polarity is reversed on an
ungrounded amplier there may be a potential of 120V present
between the amp chassis and ground. Radial Engineering takes
no responsibility for this or how the JX2 is connected or used.
It is the user’s full responsibility to ensure that proper electrical
polarity is maintained on all equipment connected to the JX2 and
that proper building electrical codes have been followed wherever
the JX2 is being used.
To reduce opportunity for shock hazard or damage to the JX2 or
connected equipment, plug the ¼” connectors into the ampliers
rst and then to the JX2. This is especially important when using
old ampliers that do not have 3-prong plugs as the possibility ex-
ists to touch the chassis ground with the connector plug tip when
the plug is inserted into the jack.
Cautions for ampliers with ungrounded 2-prong A/C cords:
Before connecting any input to an ungrounded amplier, power the
amp up and listen to the residual hum. If the amp has a two-posi-
tion ground polarity reverse switch, set the switch in the position
that produces the least residual hum from the speakers. If there
is no polarity switch, reverse the A/C plug at the outlet to nd the
least residual hum.
To ensure an ungrounded amplier does not present a shock
hazard: Test for voltage potential by connecting a voltmeter be-
tween the amplier chassis and the JX2 chassis. If voltage is pres-
ent, reverse the amplier’s A/C supply polarity and test again.
Note that due to this potential problem, damage to the JX2 or
other connected equipment caused by improper A/C polarity is
not covered by warranty.
Radial Engineering Ltd. Switchbone™ Users Guide
1 2
Radial Engineering Ltd. Switchbone™ Users Guide
True to the Music True to the Music
Of course, once you get these amps connected together, you have
to control them! This is where the Switchbone also shines! The
Switchbone is easy to use. The foot switch layout and LED readout
follows a ‘common sense’ and intuitive approach that is very natural.
We have also added a boost circuit to allow you to ‘step-up’ the output
to both amps simultaneously for a solo or extra saturation when playing
through a distorted sound. We have even added a separate output for
your tuner. This also takes the tuner out of the audio circuit thus ensuring
you get the direct tone of your guitar.
CAUTION:
When connecting two ampliers together you must ensure that they are
properly grounded as per the electrical code!
Unfortunately, we are unable to test every amplier on the market and
cannot assure that the electrical system in your house or venue has been
wired correctly. You must ensure that proper electrical codes have been
maintained and only equipment that has been certied by your country’s
electrical code is being used.
An important note about grounding:
Since guitar circuits are high-gain and high impedance,
RF noise, hum and buzz are easily induced. Connecting
equipment with different grounding schemes often results in
ground loops and more noise. The Radial JX2 addresses
these problems by employing a oating ground architecture
which requires an earth ground. This is accomplished via
the Channel-1 output. Channel-1 provides an electrical
ground from the JX2 chassis to the primary guitar amplier,
therefore always connect Channel-1 to a guitar amp with
a 3-prong grounded A/C power cord to enable a proper
ground and keep noise out.
To ensure an ungrounded (2 prong) amplier does not
present a shock hazard: Test for voltage potential by con-
necting a voltmeter between the amplier chassis and the
JX2 chassis. If voltage is present, reverse the amplier’s
A/C supply polarity and test again.
43
1. INTRODUCTION
The Radial JX2 Switchbone was born from the demand we received from
users like you. The Switchbone is in fact a pared down version of the
popular Radial JD7 Injector, a studio recording device that allows as many
as 7 ampliers to be driven from one guitar.
The Switchbone has been optimized for stage use and allows a guitar to
drive two ampliers and a tuner from one guitar input and do it without
introducing buzz, hum, or distortion.
Sounds easy enough… but it is not. For those that have tried connecting
two ampliers together using Y-cords or some of the other AB-Y boxes
that have come before, you are familiar with the many challenges:
Drop in gain, tone changes, buzz and hum just to name a few. The
Radial Switchbone is a remarkable device that deals with all of these
problems and brings forth a design that is easy to use, musical and
truly effective.
Please take the time to read this manual before you plug in. It will help you
get the most out of your Radial Switchbone and also eliminate potential
shock hazards that can occur when connecting equipment together.
2. CONCEPT
The Radial Switchbone begins with the concept that most ‘tone crazy’
players will generally use two amps on stage. (Of course more is better,
but then someone would have to carry all those amps to the gigs!)
When one drives two ampliers with one guitar, the signal from the pickup
is divided in two and the sound changes. To get around this problem,
the Switchbone employs a unique Class-A amplier circuit that has been
optimized for use with guitars. With customers like Eric Johnson, Carlos
Santana and Neal Schon, we are not allowed to alter the sound of their
favorite vintage axe. The sound must be real!
This leads to the next problem: Your guitar has now gone from being
passive to essentially becoming active. Your pickup is no longer
connected directly to the amplier. It is being ‘buffered’ (amplied). The
natural relationship is lost. To compensate for this, we have introduced
a feature called Drag™ control to allow you to reintroduce the natural
loading that is lost. With load-correction, the instrument goes back to
normal. It breathes!
Finally as soon as you connect two ampliers together they hum, they
buzz and sometimes even spark with hundreds of volts! This is due
to the way that each manufacturer builds their ampliers. Some use
positive ground, others negative. Some use the chassis as a ground
plane and some old designs from the 50’s and 60’s that do not have
proper 3-pin safety U grounds. The Radial Switchbone incorporates a
transformer isolated output, a ground lift switch and a polarity reverse
switch to allow your two ampliers to be used in tandem. These are
designed to separate and isolate the electrical current of each amplier
and eliminate ground loops.
Radial Engineering Ltd. Switchbone
™ Users Guide Radial Engineering Ltd. Switchbone™ Users Guide
True to the Music True to the Music

Specyfikacje produktu

Marka: Radial Engineering
Kategoria: Nie skategoryzowane
Model: Switchbone JX-2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Radial Engineering Switchbone JX-2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Nie skategoryzowane Radial Engineering

Radial Engineering

Radial Engineering Catapult Rack TX Instrukcja

2 Kwietnia 2025
Radial Engineering

Radial Engineering Highline Instrukcja

25 Lutego 2025
Radial Engineering

Radial Engineering Highline Stereo Instrukcja

25 Lutego 2025
Radial Engineering

Radial Engineering SubMix Instrukcja

11 Lutego 2025
Radial Engineering

Radial Engineering Switchbone JX-2 Instrukcja

11 Lutego 2025
Radial Engineering

Radial Engineering J-Rak 8 Instrukcja

11 Lutego 2025
Radial Engineering

Radial Engineering Workhorse PowerStrip Instrukcja

11 Lutego 2025
Radial Engineering

Radial Engineering PreComp Instrukcja

11 Lutego 2025
Radial Engineering

Radial Engineering Tonebone PZ-Select Instrukcja

11 Lutego 2025
Radial Engineering

Radial Engineering Q4 Instrukcja

11 Lutego 2025

Instrukcje Nie skategoryzowane

Najnowsze instrukcje dla Nie skategoryzowane

Spin Master

Spin Master 6026397 Instrukcja

3 Kwietnia 2025
EnGenius

EnGenius EPA5006HAT Instrukcja

3 Kwietnia 2025
IFM

IFM PE2599 Instrukcja

3 Kwietnia 2025
IFM

IFM RU6035 Instrukcja

3 Kwietnia 2025
Bestway

Bestway 9102S Instrukcja

3 Kwietnia 2025
Bestway

Bestway 9102T Instrukcja

3 Kwietnia 2025
Bestway

Bestway 21177 Instrukcja

3 Kwietnia 2025
Bestway

Bestway 21178 Instrukcja

3 Kwietnia 2025
Axor

Axor Starck 12456341 Instrukcja

3 Kwietnia 2025
Ruggard

Ruggard GTUV-SG Instrukcja

3 Kwietnia 2025