Instrukcja obsługi Qazqa 90501

Qazqa Ulga 90501

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Qazqa 90501 (4 stron) w kategorii Ulga. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

VAP Duo WL Silver

MODEL: 90501

INTRODUCTION

The Light incorporates a PIR (Passive Infra Red) sensing device which

continuously scans a preset operating zone and immediately switches

the light on when it detects movement in that area. This means that

whenever movement is detected within the range of the sensor the

light will switch on automatically to illuminate pathways, steps,

patios, porches, or whatever area you have selected to light for rea-

sons of safety, convenience or security.

While there is movement within range of the unit the light will

remain on.

WHILE TO FIT YOUR LIGHT

To achieve best results, we suggest you account the following points:

■ Ideally the Light should be mounted 1.8 to 2.5 meters (6 to 8ft)

above the area to be scanned (refer Figure).

■ To avoid damage to unit-do not aim the sensor towards the sun.

■ To avoid nuisance triggering, the sensor should be directed away

from heat sources such as barbecues, Air-conditioners, other

outside lighting, moving cars and ﬂue vents.

■ To avoid nuisance triggering, keeping away from the area of strong

electromagnetic disturbance.

■ Do not aim towards reﬂective surfaces such as smooth white

walls, swimming pools, etc. The Security light scanning speciﬁcati-

ons (Max. 8 meters at 130°) may vary slightly depending on the

mounting height and location. The detection range of the unit

may also alter with temperature change. Before selecting a place

to install your light you should note that movement across the

scan area is more eﬀective than movement directly toward or

away from the sensor. (refer Figure). If movement is made walking

directly towards or away from the sensor and not across, the

apparent detection range will be substantially reduced. (refer

Figure )

FITTING THE UNIT

Installation by a licensed electrician and according to IEC wiring Regu-

lation.

Before commencing any electrical work, ensure mains supply cables

are isolated by switching oﬀ and removing the relevant fuse.

1. Unscrew the Terminal Box Cover Screw then remove the Terminal

Box Cover

2. Use the Terminal Box Cover to mark the position of screw holes

onto mounting surface. Drill the wall to depth of about 30 mm

and ﬁt the plastic plugs, and then ﬁx the Cover to the mounting

surface with rightly screws. Be careful to avoid drilling or screwing

into concealed electrical wiring.

3. Connecting the Power Cable (H05RN-F 3G 1mm², not included) to

the Terminal Block, see the relative symbol. Ensure the cable must

pass through the Cable Gasket.

4. Fit the lamp body to the Terminal Box Cover. Adjusting the light

direction you desired, then tighten the screws.

5. Switch the main power on.

Important: loosen the lock nuts and screws and outdoor wall light

before making any adjustments.

4x30mm

90°

45° 45°

90°

142 mm

6x27mm

45° 45°

OFF

130° 130°

φ6mm

30mm

39.5mm

130°

H:2.5m

1min

5sec

0 2

6 8mm

UNDERSTANDING THE CONTROLS (referring to the

Figure)

ADJUSTING THE DURATION TIME: The length of time that remains

switched on after activation can be adjusted from (10±5) seconds to

(4±1) minutes. Rotating the TIME from (+) to (—) will reduce the

duration time. Note: Once the light has been triggered by the PIR

sensor any subsequent detection will start the timed period again

from the beginning.

ADJUSTING THE LUX CONTROL LEVEL: The Lux control module has a

built-in sensing device (photocell) that detects daylight and darkness.

The ( ) position denotes that the Floodlights can work at day and

night, and the ( ) position only work at night. You can set to ope-

rate the unit at the desired level by adjusting the LUX knob.

SETTING THE CONTROLS

1. Put the Lux control knob to light ( ) position, turn the wall

switch on and wait half a minute for the control circuit to stabilize.

At this stage ensure that the TIME control knob is set at minimum

(—). The light will now switch on and remain on for about 30

seconds (within 60 seconds).

2. Direct the sensor toward the desired area to be scanned by adjus-

ting the sensor.

3. Have another person move across the center of the area to be

scanned and slowly adjust the angle of the sensor until the unit

sensors the presence of the moving person, causing the Light to

switch on. (refer Figure).

4. Adjust time control to required setting.

5. To set the Lux level at which the Light will automatically switch

“on” at night, turn the LUX control knob from daylight to night. If

the Light are required to switch on earlier, e. g. Dusk, wait for the

desired light level, then slowly turn the LUX control knob towards

daylight while someone walks across the center of the area to be

detected. When the Light switch on, release the LUX control knob.

You may need to make further adjustments to achieve your ideal

light level setting.

TECHNICAL DETAILS:

Voltage:

Wattage:

Detection range:

Duration time:

Weatherproof:

Power Cable:

220-240 V ~ 50 Hz

2 ×6 ×0.5W LED

130º and Max. 8 meters

from (10±5) seconds to (4±1) minutes adjustable

IP44

3G, 1.0mm² ﬂexible cable

Specyfikacje produktu

Marka:	Qazqa
Kategoria:	Ulga
Model:	90501

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Qazqa 90501, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Ulga Qazqa

Qazqa Delux Instrukcja

30 Grudnia 2025

Qazqa Solo Instrukcja

26 Września 2024

Qazqa 91527 Instrukcja

25 Września 2024

Qazqa 91378 Instrukcja

25 Września 2024

Qazqa RLX-1201 Infrared Sensor Instruction Instrukcja

25 Września 2024

Qazqa 88898 Instrukcja

25 Września 2024

Qazqa 91370 Instrukcja

25 Września 2024

Qazqa 90501 Instrukcja

24 Września 2024

Qazqa 89433 Instrukcja

24 Września 2024

Qazqa 90502 Instrukcja

24 Września 2024

Instrukcje Ulga

Najnowsze instrukcje dla Ulga

KonstSmide 7860-370 Instrukcja

15 Stycznia 2025

Gardena 4206 Instrukcja

15 Stycznia 2025

Nedis WIFILS52CRGBW Instrukcja

15 Stycznia 2025

Philips HF3304 Instrukcja

14 Stycznia 2025

Nedis BTTNTP-22W60 Instrukcja

14 Stycznia 2025

Nedis BTTNTP-44W120 Instrukcja

14 Stycznia 2025

Livarno IAN 103915 Instrukcja

13 Stycznia 2025

ION Party Ball USB Instrukcja

13 Stycznia 2025

Livarno IAN 292038 Instrukcja

12 Stycznia 2025

Eurolite LED TMH-17 Instrukcja

12 Stycznia 2025