Instrukcja obsługi Pyle Pro PDIC66

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pyle Pro PDIC66 (1 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/1
IN-CEILING SPEAKER
INSTALLATION MANUAL
www.pyleaudio.com
INSTALLATIONTECHNICAL PARAMETERS
TROUBLESHOOTING
IF T HERE IS NO SOUND FROM ANY OF THE SPEAKERS:
IF T HERE IS NO SOUND COMING FROM ONE SPEAKERS:
IF T HERE IS LOW(OR NO) BASS OUT PUT :
IF T HE SYSTEM PLAYS AT LO W VOLUM ES BUT SHUT S OFF AS VOLUM E IS INCREASED:
TOOLS NEEDED
The in-wall/in-ceiling speakers
were designed to be easily
installed.However,if you are
unsure of your ability to prop-
erly install these loudspeakers
please contact your dealer or a
quali fied installer.
Pencil Phillips #2 screwdriver
Measuring tape Utility knife
Carpenter’s level Awl
Check that receiver/amplifier is on and a source is playing.
Check all wires and connections between receiver/amplifier and speakers.Make sure all wires are connected.Make
sure none of the speaker wires are frayed,cut,punctured or tounching each other.
Review proper proper operation of your receiver/amplifier.
Check the“Balance”control on your receiver/amplifier.
Check allwires and connections between receiver/amplifier and speakers.Make sure all wires are connected.Make
sure none of the speaker wires are frayed,cut,punctured or tpunching each other.
Make sure the connections to the left and right“speaker Inputs”have the correct polarity(+ and -).
Consider adding a powered subwoofer to your system.
In Dolby Digital or DT S modes,make sure your receiver/processor is corectly configured.When using a subwoofer,
make sure thesubwoofer output of the receiver/processor has been enabled.If no subwoofer is being used,
make sure the left and right front and rear speakers have been configured as“LARGE”See your receiver/processor’s
owner’s manual for futher information on correct speaker configuration in Dolby Digital,DTS and other surround sound
modes.
Check all wires and connections between receiver/amplifier and speakers.Make sure all wires are connected.Make
sure none of the speaker wires are frayed,cut,punctured or touching each other.
If more than one pair of main speakers is being used,check the minimum-impedance requirements of your
receiver/amplifier.
Thank you for purchasing this PYLE in-wall/in-ceiling speaker system.It is a
state-of-the-art product carefully designed and manuf act ured for your installation
needs,and has been t horoughly tested to ensure consistent and reliable perfor-
mance.
If you have any question about the installation or operation of your PYLE
in-wall/in-ceiling speaker system which are not answered by this manual,contact
your dealer immediately.
INCLUDED
SPEAKER CONNECTIONS
REAR SPEAKERS
IN- CEILING
CONNECTION TIPS
SPEAKER PLACEMNT
IN- CEILING SPEAKERS
EXISTING CONSTRUCTION
IN- CEILING SPEAKERS
FRONT SPEAKERS
srtips of
adhesive Screws Tem plate
One pair of speakers with grilles.
One pc of speakers with grills
for PDIC56/PDIC66/PDIC86/PDIC106
M4x60mm
4pcs
40 60
0 0
WALL
5-6FT
WALL WALL WALL WALL
LEFT RIGHT
LEFT RIGHT
Front or Rear S peaker Outputs
Proper placement of the speakers is an imporant step in obtaining
the most realistic sound stage possible.These recommendations are
for the optimum placement of the londspeakers.Use these placement
recommendations as a guide. Slight variations will not diminish your
listening pleasure.The front speakers should be placed the same di--
stance from each other as they are from the listening position.They
should be placed at about the same height from the floor as the liste-
ner’s ears will be,with the tweeters aimed toward the listener at ear-level height.In a home theater configu-
ration,the two surround,speakers should be placed slightly behind the listening position and ideally should
face each other and be at a level higher than the listener’s ears.If that is not possible,they may be placed in
a wall(or in the ceiling)behind the listening position,facing forword.The surround speakers should not call
attention to themselves.T hey should provide a diffuse,ambient sound accompanying the main program mat-
erial heard in the front speakers. In Dolby*Digital and DTS systems,aim the tweeters toward the listening
position at ear-level height.
The wires for bot h speakers
should be the same length.If
one speaker is placed closer to
the amplifer than the other,
hide the excess wire behid
the wall.Speakers and elec-
tronics terminals have corre-
sponding(+)and(-)terminals.
We use red to denote the(+)termi-
nal and black for t he(-)termi-
nal.It is important to connect
both speakers identically:(+)on
the speaker to(+)on the ampli-
fier and(-)on the speaker to(-)
on the amplifier.Wireing out
of phase” result s in thin sound,
weak bass and a poor stereo
image.With t he advent of mult i-
channel surround sound
systems,connecting all of the
speakers in your system with
the correct polarity remains
equally important in order to
preserve the proper ambience
and directionality of the
program material.
5.25 " 2- W ay Ce g Sp  Syst
*Blac k PP  Co ne W i Ru er  dg
*1/2" Ti nim   om e  Tw ee er In  ivel M o nt
P o w e r: 15 0  ats R a ted  P eak
Frequency Response: 80HZ- 20KH Z
*I p ed a nce : 8  Oh m
*Sen siviy: 8 8  dB   
*w ith E lectr o nic C rosso ver N etw o rk
*Su pp le d W h Ro un d Gr ie s A n d S q ua re  G rlles
*Size : Ro un d  /  S qu are G r ie s: 8   ”/8    ”*8   ”    
*Cutou t Size :6  ”   
*M o un tng De pth :3 ”  
PD6 P66
PD6 PDI106
10
10
10
6." -W ay ei g Spe ker Sys
*Blac k PP  Co ne W i Ru er  dg
*1/2" Ti nim   om e  Tw ee er In  ivel M o nt
Pow er 200 W atts Rated Peak
Frequency Response: 60HZ- 20KH Z
*I p ed a nce : 8  Oh m
*Sen siviy: 8 9  dB   
*w ith E lectr o nic Crosso ver  etw ork
*Su pp le d W h Ro un d Gr ie s A n d  Sq ua re  G rie s
*Size : Ro un d  /  S qu are G r ie s: 9   ”/9    ”*9   ”    
*Cutou t Size:8 ”  
*M o un tng De pth :3 ”  
8" 2 - W ay  C eiing  S p ea ker S y ste m
*Blac k PP  Co ne W i Ru er  dg
*1/2" Ti nim   om e  Tw ee er In  ivel M o nt
Pow er 250 W atts Rated Peak
Frequency Response: 40HZ- 20KH Z
*I p ed a nce : 8  Oh m
*Sen siviy: 8 9  dB   
*w ith E lectr o nic Crosso ver  etw ork
*Su pp le d W h Ro un d Gr ie s A n d  Sq ua re  G rie s
*Size : Ro u nd  / Sq u are  rie s: 11  ” /11   ” *11  ”    
*Cutou t Size :9  ”   
*M o un tng De pth :3   ”  
10" 2- W a y Ceiln g pe ak er  e m
*Blac k PP  Co ne W i Ru er  dg
*1/2" Ti nim   om e  Tw ee er In  ivel M o nt
Pow er 300 W atts Rated Peak
Frequency Response: 35HZ- 20KH Z
*I p ed a nce : 8  Oh m
*Sen siviy: 8 9  dB   
*w ith E lectr o nic Crosso ver  etw ork
*Su pp le d W h Ro un d Gr ie s A n d  Sq ua re  G rie s
*Size : Ro un d  /  S qu are G r ie s: 12   ”/12   ”*12   ”     
*Cutou t Size :0   ”  
*M o un tng De pth :3    ”  
/ 4
This  p rod uct g ets  h e p a te nt of n nov atn  he  s tuctu re, e asy  o r  n sa la ton.
U se new  environm en tal protecton  A B S  ateria l w ih  on ge r s erv ice fe, no t e asy  o  ch ang e c olor.
Cut the drywall.
Note:Always allow at least
one- half inch between a wall
stud and the speaker cutout or
the locking tabs will not be able
to swivel into place.
Connect the speaker wires to
the speaker.
Replace the metal grille. Complete.
Screw d own each of the four
Phillips head screws.The
locking tabs will swivel into
place and secure the unit to
the rear surface of the drywall.
Put in the strips of adhesive to
secure the grille.
-2- - 3- -4- -5- - 6-
1600-63rd Street
Brooklyn,NY 11204 USA

Specyfikacje produktu

Marka: Pyle Pro
Kategoria: głośnik
Model: PDIC66

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Pyle Pro PDIC66, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje głośnik Pyle Pro

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024