Instrukcja obsługi Praktica Luxmedia Z212

Praktica kamera Luxmedia Z212

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Praktica Luxmedia Z212 (91 stron) w kategorii kamera. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/91
1
Preface
About this Manual
• The contents of this manual and the bundled Basic Reference are subject
to change without notice.
• Note that the example screens and product illustrations shown in this
User’s Guide may differ somewhat from the screens and configuration of
the actual camera.
Copyright
This manual contains proprietary information protected by copyright. All rights
are reserved. No part of this manual may be reproduced by any mechanical,
electronic or other means, in any form, without prior written permission of the
manufacturer.
© Copyright 2015
Declaration of Conformity
This device complies with Part 15 of the FCC rules. Operation is subject to the
following conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference
that may cause undesired operation.
CE Mark Warning
This is a Class B product, in a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
FCC: SAR standard Value: 1.6 W/Kg, Maximal Measure: 0.27 W/Kg
CE: SAR standard Value: 2.0 W/Kg, Maximal Measure: 0.077 W/Kg
Trademark Recognition
Windows XP/Vista/Win7/Win 8 are registered trademarks of Microsoft
Corporation in the United States and/or other countries. Windows is an
abbreviated term referring to the Microsoft Windows Operation System. All
other companies or product names are trademarks or registered trademarks
of their respective companies.
Federal Communication Commission Interference Statement
APPLIES TO USA AND CANADA ONLY
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
2
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following
conditions:
1)
The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2)
The transmitter module may not be co-located with any other transmitter
or antenna.
As long as 2 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their end-
product for any additional compliance requirements required with this module
installed.
3
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID can
not be used on the final product. In these circumstances, the OEM integrator
will be responsible for re-evaluating the end product (including the
transmitter) and obtaining a separate FCC authorization.
End Product Labelling
This transmitter module is authorized only for use in a device where the
antenna may be installed such that 20 cm may be maintained between the
antenna and users. The final end product must be labelled in a visible area
with the following: "Contains FCC ID: 2AAD3AA0D0". The grantee's FCC ID
can be used only when all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end
user regarding how to install or remove this RF module in the user’s manual
of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as shown in this manual.
Industry Canada statement
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable
aux appareils radio exempts de licence. Son fonctionnement est sujet aux
deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris
un brouillage susceptible de provoquer un fonctionnement indésirable.
This device is intended only for OEM integrators under the following
conditions: (For module device use)
1)
The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2)
The transmitter module may not be co-located with any other transmitter
or antenna.
As long as 2 conditions above are met, further transmitter tests will not be
required. However, the OEM integrator is still responsible for testing their end-
product for any additional compliance requirements when this module is
installed.

Specyfikacje produktu

Marka: Praktica
Kategoria: kamera
Model: Luxmedia Z212

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Praktica Luxmedia Z212, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje kamera Praktica

Praktica

Praktica Luxmedia WP240 Instrukcja

21 Września 2024
Praktica

Praktica Luxmedia Z212 Instrukcja

21 Września 2024
Praktica

Praktica Luxmedia Z250 Instrukcja

18 Września 2024

Instrukcje kamera

Najnowsze instrukcje dla kamera

Trust

Trust Powerc@m 820 Instrukcja

15 Października 2024
AVerMedia

AVerMedia Live Streamer CAP 4K BU113 Instrukcja

15 Października 2024
Bushnell

Bushnell Trophy Cam 119456 Instrukcja

13 Października 2024
Konica Minolta

Konica Minolta Hi-Matic GF Instrukcja

11 Października 2024
Easypix

Easypix KiddyPix Blizz Instrukcja

10 Października 2024
Samsung

Samsung DV1506F Instrukcja

9 Października 2024
Kogan

Kogan KAUNCAMBLUA Instrukcja

9 Października 2024
Polaroid

Polaroid 600 Series Instrukcja

9 Października 2024
Kogan

Kogan KAKIDINCMRB Instrukcja

8 Października 2024
UniView

UniView IPC3615SB-ADF28(40)KM-I0 Instrukcja

8 Października 2024