Instrukcja obsługi Pioneer GM-D9705

Pioneer odbiornik GM-D9705

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pioneer GM-D9705 (14 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/14

PIONEER CORPORATION

28-8, Honkomagome 2-chome, Bunkyo-ku,

Tokyo 113-0021, JAPAN

PIONEER ELECTRONICS (USA) INC.

P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.

TEL: (800) 421-1404

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique

TEL: (0) 3/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

2 Jalan Kilang Barat, #07-01, Singapore 159346

TEL: 65-6378-7888

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

5 Arco Lane, Heatherton, Victoria, 3202 Australia

TEL: (03) 9586-6300

PIONEER ELECTRONICS DE MÉXICO S.A. DE C.V.

Blvd.Manuel Ávila Camacho 138, 10 piso

Col.Lomas de Chapultepec, México, D.F. 11000

TEL: 52-55-9178-4270

FAX: 52-55-5202-3714

先公鋒股份有限司

台北區市內湖瑞光路407 8號樓

電話：886-(0)2-2657-3588

先公鋒電限子（）香港有司

香港九龍長沙灣道909 5號樓

電話：852-2848-6488

Tous droits de reproduction et de

traduction réservés.

<5707000013140V> EL

Visitez-nous sur le Web à

Thank you for purchasing this PIONEER

product

To ensure proper use, please read through this

manual before using this product. It is espe-

cially important that you read and observe

WARNING CAUTIONs and s in this manual.

Please keep the manual in a safe and accessible

place for future reference.

If you want to dispose this product, do not mix

it with general household waste. There is a se-

parate collection system for used electronic

products in accordance with legislation that re-

quires proper treatment, recovery and recy-

cling.

Private households in the member states of

the EU, in Switzerland and Norway may return

their used electronic products free of charge

to designated collection facilities or to a retai-

ler (if you purchase a similar new one).

For countries not mentioned above, please

contact your local authorities for the correct

method of disposal.

By doing so you will ensure that your disposed

product undergoes the necessary treatment,

recovery and recycling and thus prevent po-

tential negative effects on the environment

and human health.

Information to User

Alteration or modifications carried out without

appropriate authorization may invalidate the

user s right to operate the equipment.’

Visit our website

Visit us at the following site:

http://pioneer.jp/en/info/globalnetwork/

We offer the latest information about

PIONEER CORPORATION on our website.

The Safety of Your Ears is in

Your Hands

Get the most out of your equipment by playing

it at a safe level a level that lets the sound—

come through clearly without annoying blar-

ing or distortion and, most importantly, with-

out affecting your sensitive hearing. Sound

can be deceiving. Over time, your hearing

“ ”comfort level adapts to higher volumes of

sound, so what sounds normal can actually“ ”

be loud and harmful to your hearing. Guard

against this by setting your equipment at a

safe level BEFORE your hearing adapts.

ESTABLISH A SAFE LEVEL:

!Set your volume control at a low setting.

!Slowly increase the sound until you can

hear it comfortably and clearly, without dis-

tortion.

!Once you have established a comfortable

sound level, set the dial and leave it there.

BE SURE TO OBSERVE THE FOLLOWING

GUIDELINES:

!Do not turn up the volume so high that you

can t hear what s around you.’ ’

!Use caution or temporarily discontinue use

in potentially hazardous situations.

!Do not use headphones while operating a

motorized vehicle; the use of headphones

may create a traffic hazard and is illegal in

many areas.

Before you start

If you experience problems

Should this product fail to operate properly,

please contact your dealer or nearest author-

ized Pioneer Service Station.

Before connecting/

installing the amplifier

WARNING

!This product contains chemicals known to the

State of California and other governmental en-

tities tocause cancer and birth defects or

other reproductive harm. Wash hands after

handling.

!Slots and openings in the cabinet are provided

for ventilation to ensure reliable operation of

the product, and to protect it from overheat-

ing. To prevent fire hazard, the openings

should never be blocked or covered with items

(such as papers, floor mat, cloths).

!This unit is for vehicles with a 12 V battery and

negative grounding. Before installing in re-

creational vehicles, trucks or buses, check the

battery voltage.

!When installing this unit, make sure to con-

nect the ground wire first. Ensure that the

ground wire is properly connected to metal

parts of the car s body. The ground wire of the’

one of this unit must be connected to the car

separately with different screws. If the screw

for the ground wire loosens or falls out, it

could result in fire, generation of smoke or

malfunction.

!Be sure to install the fuse to the battery wire.

!Always use a fuse of the rating prescribed.

The use of an improper fuse could result in

overheating and smoke, damage to the pro-

duct and injury, including burns.

!Check the connections of the power supply

and speakers if the fuse of the separately sold

battery wire or the amplifier fuse blows. Deter-

mine and resolve the cause, then replace the

fuse with and identical equivalent.

!Always install the amplifier on a flat surface.

Do not install the amplifier on a surface that

is not flat or on a surface with a protrusion.

Doing so could result in malfunction.

!When installing the amplifier, do not allow

parts such as extra screws to get caught be-

tween the amplifier and the automobile.

Doing so could cause malfunction.

!Do not allow this unit to come into contact

with liquids. Electrical shock could result.

Also, damage to this unit, smoke, and over-

heating could result from contact with liquids.

The surfaces of the amplifier and any attached

speakers may also heat up and cause minor

burns.

!In the event of any abnormality, the power

supply to the amplifier is cut off to prevent

equipment malfunction. If this occurs, switch

the system power off and check the power

supply and speaker connections. If you are un-

able to determine the cause, please contact

your dealer.

!Always disconnect the negative terminal of*

the battery beforehand to avoid the risk of

electric shock or short circuit during installa-

tion.

!Do not attempt to disassemble or modify this

unit. Doing so may result in fire, electric

shock or other malfunction.

CAUTION

!Always keep the volume low enough to hear

outside sounds.

!Extended use of the car stereo while the en-

gine is at rest or idling may exhaust the bat-

tery.

!This product is evaluated in moderate and tro-

pical climate condition under the Audio, video

and similar electronic apparatus - Safety re-

quirements, IEC 60065.

!The graphical symbol placed on the

product means direct current.

Before you start

Owner’s Manual

Mode d’emploi

CLASS D FIVE-CHANNEL AMPLIFIER

AMPLIFICATEUR À CINQ CANAUX DE CLASSE D

GM-D9705

GM-DX975

English

Français

About the protection function

This product has protection function. When this

product detects something abnormal, the follow-

ing functions will operate to protect the product

and speaker output.

!The indicator will turn redPOWER/PROTECT

and the amplifier will shut down in the situa-

tions outlined below.

—If a DC voltage is applied to the speaker

output terminal.

!The indicator will turn redPOWER/PROTECT

and the output will be muted in the situations

outlined below.

—If the speaker output terminal and speaker

wire are short-circuited.

—If the subwoofer output terminal and sub-

woofer wire are short-circuited.

!The amplifier will reduce the power output if

the temperature inside the amplifier gets

high. If the temperature gets too high, the

POWER/PROTECT indicator will turn off, and

the amplifier will shut down.

Component names and

functions

Front side

43 321 12

673819

Rear side

To adjust the switch, use a flathead screwdri-

ver if needed.

1FREQ (cut off frequency) control

Cut off frequency selectable from 40 Hz to

500 Hz.

!Set the / select switch to orLPF HPF LPF

HPF according to the type of frequency

that you want to cut off.

2LPF (low-pass filter)/HPF (high-pass fil-

ter) select switch

Switch the settings based on the connected

speaker.

!When a full-range speaker is connected,

select or . eliminates low-HPF OFF HPF

range frequency and outputs high-range

frequency. outputs the entire fre-OFF

quency range.

!When a low-range speaker or subwoofer

is connected, select .LPF

3GAIN (gain) control

Adjusting the gain controls helps align the

car stereo output to the Pioneer amplifier.

The default setting is the position.NORMAL

Before you start Setting the unit

If the output remains low, even when the car

stereo volume is turned up, turn the con-

trols to a lower level. If distortion occurs

when the car stereo volume is turned up,

turn these controls to a higher level.

!In case of a bridge connection, set the

gain controls for speaker outputs A and

B to the same position.

!For use with an RCA equipped car stereo

(standard output of 500 mV), set to the

NORMAL position. For use with an RCA

equipped Pioneer car stereo, with maxi-

mum output of 4 V or more, adjust level

to match that of the car stereo output.

!For use with an RCA equipped car stereo

with output of 4 V, set to the position.H

42CH-4CH INPUT SELECT (input select)

switch

For details, refer to Connecting the car

stereo.

5SP INPUT (speaker input) terminal

Please see the following section for speaker

connection instructions. Refer to Connec-

tions when using the speaker input wire.

6POWER/PROTECT indicator

The power indicator lights up to indicate

power ON.

!If something is not normal, the indicator

turns red.

7A/B-SW INPUT SELECT (input select)

switch

For details, refer to Connecting the car

stereo.

8SLOPE (slope) select switch

Select the slope of LPF from 12 dB (shallow–

slope) or 24 dB (sharp slope).–

9BB-REMOTE (bass boost level remote

control) jack

By connecting the Bass boost level remote

control to the jack on the main unit, you will

be able to select a bass boost level from

0 dB to 18 dB.

!The bass boost level setting applies only

to the subwoofer output.

!For instruction of connecting the bass

boost remote control to the amplifier, see

the .Connection diagram

Setting gain properly

!Protective function included to prevent

malfunction of the unit and/or speakers

due to excessive output, improper use or

improper connection.

!When outputting high volume sound etc.,

this function cuts off the output for a few

seconds as a normal function, but output

is restored when the volume of the head

unit is turned down.

!A cut in sound output may indicate impro-

per setting of the gain control. To ensure

continuous sound output with the head

unit at a high volume, set amplifier gain

control to a level appropriate for the preout

maximum output level of the head unit, so

that volume can remain unchanged and to

control excess output.

!Despite correct volume and gain settings,

the unit sound still cuts out periodically. In

such cases, please contact the nearest

authorized Pioneer Service Station.

Gain control of this unit

Preout level: 2 V (Standard: 500 mV)

Preout level: 4 V

Above illustration shows gain set-NORMAL

ting.

Setting the unit

Relationship between amplifier gain

and head unit output power

If amplifier gain is raised improperly, this will

simply increase distortion, with little increase

in power.

Signal waveform when outputting at

high volume using amplifier gain

control

If the signal waveform is distorted due to high

output, even if the amplifier gain is raised, the

output power will change only slightly.

Connection diagram

3 4

1Battery wire (sold separately)

!The maximum length of the wire be-

tween the fuse and the positive term-+

inal of the battery is 30 cm (12 in.).

!For the wire size, refer to Connecting the

power terminal. The battery wire, the

ground wire and the optional direct

ground wire must be same size. After

making all other connections at the am-

plifier, connect the battery wire terminal

of the amplifier to the positive term-+

inal of the battery.

2Fuse (100 A) (sold separately)

Each amplifier must be separately fused at

100 A.

3Positive terminal+

4Negative ( ) terminal*

5Battery (sold separately)

6Ground wire, Terminal (sold separately)

Setting the unit Connecting the units

The ground wires must be same size as the

battery wire.

Connect to metal body or chassis.

7External output

If only one input plug is used, do not connect

anything to RCA input jack B or RCA subwoo-

fer input jack.

8Car stereo with RCA output jacks (sold sepa-

rately)

9Connecting wire with RCA pin plugs (sold se-

parately)

aBass boost level remote control

bBass boost level remote control wire (5 m

(16 ft. 5 in.))

cRCA input jack A

dRCA input jack B

eRCA subwoofer input jack

fFront side

gFuse (30 A) × 3

hSpeaker/subwoofer output terminals

Please see the following section for speaker

connection instructions. Refer to Connections

when using the speaker input wire.

iRear side

jSystem remote control wire (sold separately)

Connect male terminal of this wire to the sys-

tem remote control terminal of the car stereo.

The female terminal can be connected to the

auto-antenna relay control terminal. If the car

stereo lacks a system remote control terminal,

connect the male terminal to the power term-

inal via the ignition switch.

Note

INPUT SELECT (input select) switch must be set.

For details, refer to .Connecting the car stereo

Before connecting the

amplifier

WARNING

!Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap sections

in contact with metal parts in adhesive tape.

!Never cut the insulation of the power supply

to feed power to other equipment. Current ca-

pacity of the wire is limited.

CAUTION

!Never wire the speaker negative cable directly

to ground.

!Never band together multiple speaker s nega-’

tive cables.

!If the system remote control wire of the ampli-

fier is connected to the power terminal via the

ignition switch (12 V DC), the amplifier will re-

main on with the ignition whether the car

stereo is on or off, which may exhaust battery

if the engine is at rest or idling.

!Install and route the separately sold battery

wire as far as possible from the speaker wires.

Install and route the separately sold battery

wire, ground wire, speaker wires and the am-

plifier as far away as possible from the anten-

na, antenna cable and tuner.

About bridged mode

!The maximum speaker impedance is 4 W.

Please carefully check. Improper connection

to the amplifier may result in malfunction or

personal injury due to burns from overheat-

ing.

Connecting the units

Specyfikacje produktu

Marka:	Pioneer
Kategoria:	odbiornik
Model:	GM-D9705

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Pioneer GM-D9705, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje odbiornik Pioneer

Pioneer SX-303RDS Instrukcja

10 Października 2024

Pioneer GM-D500M Instrukcja

6 Października 2024

Pioneer VSX-535 Instrukcja

4 Października 2024

Pioneer A-10EB Instrukcja

23 Września 2024

Pioneer VSX-531D-B Instrukcja

21 Września 2024

Pioneer DMH-342EX Instrukcja

21 Września 2024

Pioneer DMH-340EX Instrukcja

17 Września 2024

Pioneer AVH-A215BT Instrukcja

14 Września 2024

Pioneer A-10 Instrukcja

14 Września 2024

Pioneer DEH-1550B Instrukcja

14 Września 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Denon AVR-S900W Instrukcja

15 Października 2024

Pro-Ject Amp Box DS2 Instrukcja

15 Października 2024

AKG HP12U Instrukcja

15 Października 2024

Apart SBR160 Instrukcja

14 Października 2024

American Audio VLP 600 Instrukcja

14 Października 2024

Chord Anni Instrukcja

14 Października 2024

Sennheiser EM 9046 SU Instrukcja

14 Października 2024

Yamaha MusicCast RX-V481 Instrukcja

13 Października 2024

JL Audio VX600/6i Instrukcja

12 Października 2024

Denon AVR-991 Instrukcja

10 Października 2024