Instrukcja obsługi Pioneer AVIC-X950BH

Pioneer Nawigacja AVIC-X950BH

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pioneer AVIC-X950BH (65 stron) w kategorii Nawigacja. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/65
Installation Manual
Manuel d installation
MULTIMEDIA NAVIGATION RECEIVER
RECEPTEUR DE NAVIGATION MULTIMEDIA
AVIC-Z150BH
AVIC-X950BH
AVIC-X850BT
AVIC-X8510BT
English Français
Precautions
Your new navigation system and this
manual 3
Important safeguards 3
Connecting the system
Precautions before connecting the
system 5
Before installing this product 5
To prevent damage 6
Notice for the blue/white lead 6
Parts supplied 7
Installing the HDMI® cable holder 7
Connecting the system 8
When connecting the iPhone 9
When connecting the Android device (for
AVIC-Z150BH and AVIC-X950BH) 11
Connecting the power cord (1) 12
Connecting the power cord (2) 14
When connecting to separately sold power
amp 16
When connecting a rear view camera 18
When connecting the external video
component 19
Using an AV input (AV1) 19
Using an AV input (AV2) 20
When connecting the rear display 20
When using a rear display connected to
rear video output 20
Installation
Precautions before installation 21
To avoid electromagnetic interference 21
Before installing 21
For AVIC-Z150BH users 22
Installing the navigation system 22
Installation notes 22
Parts supplied 23
Installation using the screw holes on
the side of the navigation unit 23
Fastening the detachable faceplate 24
Installing the GPS antenna 25
Installation notes 25
Parts supplied 25
When installing the antenna inside the
vehicle (on the dashboard or rear
shelf) 26
Installing the microphone 27
Parts supplied 27
Mounting on the sun visor 27
Installation on the steering column 28
Adjusting the microphone angle 28
Contents
En
2
Your new navigation
system and this manual
!The navigation features of this product
(and the rear view camera option if pur-
chased) are intended solely to aid you in
the operation of your vehicle. It is not a sub-
stitute for your attentiveness, judgment
and care when driving.
!Never use this navigation system to route
to hospitals, police stations, or similar facil-
ities in an emergency. Please call the ap-
propriate emergency number.
!Do not operate this navigation system (or
the rear view camera option if purchased) if
doing so will divert your attention in any
way from the safe operation of your vehicle.
Always observe safe driving rules and fol-
low all existing traffic regulations. If you ex-
perience difficulty in operating the system
or reading the display, park your vehicle in
a safe location and apply the parking brake
before making the necessary adjustments.
!This manual explains how to install this na-
vigation system in your vehicle. Operation
of this navigation system is explained in
the separate manuals for the navigation
system.
!Do not install this product where it may (i)
obstruct the driver s vision, (ii) impair the
performance of any of the vehicle s operat-
ing systems of safety features, including
airbags, hazard lamp buttons, or (iii) impair
the driver s ability to safely operate the vehi-
cle. In some cases, it may not be possible
to install this product because of the vehi-
cle type or the shape of the vehicle inter-
ior.
Important safeguards
WARNING
Pioneer does not recommend that you install
your navigation system yourself. This pro-
duct is designed for professional installation
only. We recommend that only authorized
Pioneer service personnel, who have special
training and experience in mobile electro-
nics, set up and install this product. NEVER
SERVICE THIS PRODUCT YOURSELF. In-
stalling or servicing this product and its con-
necting cables may expose you to the risk of
electric shock or other hazards, and can
cause damage to the navigation system that
is not covered by warranty.
!Read this manual fully and carefully before
installing your navigation system.
!Keep this manual handy for future refer-
ence.
!Pay close attention to all warnings in this
manual and follow the instructions care-
fully.
!This navigation system may in certain cir-
cumstances display inaccurate position of
your vehicle, the distance of objects shown
on the screen, and compass directions. In
addition, the system has certain limita-
tions, including the inability to identify one-
way streets, temporary traffic restrictions
and potentially unsafe driving areas. Please
exercise your own judgment in the light of
actual driving conditions.
!As with any accessory in your vehicle s in-
terior, the navigation system should not di-
vert your attention from the safe operation
of your vehicle as it may result in serious
injury or death. If you experience difficulty
in operating the system or reading the dis-
play, please make adjustments while safely
parked.
!Please remember to wear your seat belt at
all times while operating your vehicle. If
you are in an accident, your injuries can be
considerably more severe if your seat belt
is not properly buckled.
En 3
English
Section
01
Precautions
!Certain country and government laws may
prohibit or restrict the placement and use
of this system in your vehicle. Please com-
ply with all applicable laws and regulations
regarding the use, installation and opera-
tion of your navigation system.
En
4
Section
01
Precautions
Precautions before
connecting the system
WARNING
Do not take any steps to tamper with or dis-
able the parking brake interlock system
which is in place for your protection. Tamper-
ing with or disabling the parking brake inter-
lock system could result in serious injury or
death.
CAUTION
!If you decide to perform the installation
yourself, and have special training and ex-
perience in the mobile electronics instal-
lations, please carefully follow all of the
steps in the installation manual.
!Secure all wiring with cable clamps or
electrical tape. Do not allow any bare wir-
ing to remain exposed.
!Do not directly connect the yellow lead of
this product to the vehicle battery. If the
lead is directly connected to the battery,
engine vibration may eventually cause
the insulation to fail at the point where
the wire passes from the passenger com-
partment into the engine compartment. If
the yellow lead s insulation tears as a re-
sult of contact with metal parts, short-cir-
cuiting can occur, resulting in
considerable danger.
!It is extremely dangerous to allow cables
to become wound around the steering col-
umn or shift lever. Be sure to install this
product, its cables, and wiring away in
such so that they will not obstruct or hin-
der driving.
!Make sure that the cables and wires will
not interfere with or become caught in
any of the vehicle s moving parts, espe-
cially the steering wheel, shift lever, park-
ing brake, sliding seat tracks, doors, or
any of the vehicle s controls.
!Do not route wires where they will be ex-
posed to high temperatures. If the insula-
tion heats up, wires may become
damaged, resulting in a short circuit or
malfunction and permanent damage to
the product.
!Do not cut the GPS antenna cable to
shorten it or use an extension to make it
longer. Altering the antenna cable could
result in a short circuit or malfunction.
!Do not shorten any leads. If you do, the
protection circuit (fuse holder, fuse resis-
tor or filter, etc.) may fail to work properly.
!Never feed power to other electronic pro-
ducts by cutting the insulation of the
power supply lead of the navigation sys-
tem and tapping into the lead. The current
capacity of the lead will be exceeded,
causing overheating.
Before installing this product
!Use this unit with a 12-volt battery and ne-
gative grounding only. Failure to do so may
result in a fire or malfunction.
!To avoid shorts in the electrical system, be
sure to disconnect the ( ) battery cable be-
fore installation.
En 5
English
Section
02
Connecting the system
To prevent damage
WARNING
! Use speakers over 50 W (output value)
and between 4 to 8 (impedance value).W W
Do not use 1 to 3 speakers for thisW W
unit.
! The black cable is ground. When instal-
ling this unit or power amp (sold sepa-
rately), make sure to connect the ground
wire first. Ensure that the ground wire is
properly connected to metal parts of the
car s body. The ground wire of the power
amp and the one of this unit or any other
device must be connected to the car sepa-
rately with different screws. If the screw
for the ground wire loosens or falls out, it
could result in fire generation of smoke or
malfunction.
Ground wire
Metal parts of cars bod
y
Power amp
Other devices
(Another electronic
device in the car)
*1Not supplied for this unit.
! When replacing the fuse, be sure to only
use a fuse of the rating prescribed on this
product.
! When disconnecting a connector, pull the
connector itself. Do not pull the lead, as
you may pull it out of the connector.
! This product cannot be installed in a vehi-
cle without ACC (accessory) position on
the ignition switch.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
ACC position No ACC position
! To avoid short-circuiting, cover the discon-
nected lead with insulating tape. It is espe-
cially important to insulate all unused
speaker leads, which if left uncovered may
cause a short circuit.
! Attach the connectors of the same color to
the corresponding colored port, i.e., blue
connector to the blue port, black to black,
etc.
! Refer to the owner s manual for details on
connecting the power amp and other units,
then make connections accordingly.
! Since a unique BPTL circuit is employed,
do not directly ground the side of the*
speaker lead or connect the side of an-*
other side of the speaker lead together. Be
sure to connect the side of the speaker*
lead to the side of the speaker lead on*
this navigation system.
Notice for the blue/white lead
! When the ignition switch is turned on (ACC
ON), a control signal is output through the
blue/white lead. Connect to an external
power amp s system remote control term-
inal, the auto-antenna relay control term-
inal, or the antenna booster power control
terminal (max. 300 mA 12 V DC). The con-
trol signal is output through the blue/white
lead, even if the audio source is switched
off.
! Be sure not to use this lead as the power
supply lead for the external power amps.
Such connection could cause excessive
current drain and malfunction.
! Be sure not to use this lead as the power
supply lead for the auto-antenna or anten-
na booster. Such connection could cause
excessive current drain and malfunction.
En
6
Section
02
Connecting the system
Parts supplied
Parts marked (*) are supplied with AVIC-
Z150BH and AVIC-X950BH.
The navigation unit Power cord
RCA connector GPS antenna
Microphone HDMI cable holder*
Mini-jack extension
cable
Installing the HDMI ®cable
holder
1 Insert the lower tab of the HDMI cable
holder into the groove of this product.
Groove
Tab
2 Insert the two upper tabs into the this
product by pushing the HDMI cable holder.
Tabs
p Use the HDMI cable holder when you con-
nect this product with the separately sold
App Connectivity Kit (CD-AH200), HDMI/
USB interface cable for iPod / iPhone (CD-
IH202) or VGA/USB interface cable for iPod
/ iPhone (CD-IV202NAVI).
p Never grip the holder tightly or use force
when removing or attaching.
En 7
English
Section
02
Connecting the system
Connecting the system
The navigation unit
Wired remote input
Please refer to the instruction manual for
the Hard-wired remote control adapter
(sold separately).
SiriusXM Connect Vehicle Tuner
Please refer to the instruction manual
for SiriusXM Connect Vehicle Tuner
(sold separately).
WARNING
· To avoid the risk of accident and the potential violation of applicable laws, this
product should never be used while the vehicle is being driven except for
navigation purposes. And, also rear displays should not be in a location where it
is a visible distraction to the driver.
· In some countries, the viewing of images on a display inside a vehicle even by
persons other than the driver may be illegal. Where such regulations apply they
must be obeyed and this product’s video source should not be used.
3.55 m (11 ft. 8 in.)
GPS antenna
Antenna jack
Vehicle antenna
Microphone
4 m (13 ft. 1 in.)
En
8
Section
02
Connecting the system
When connecting the iPhone
Lightning to VGA Adapter
(Apple Inc. products)
(sold separately)
Lightning Digital AV Adapter
(Apple Inc. products)
(sold separately)
Lightning to USB Cable
(supplied with iPhone with Lightning connector)
High speed HDMI ® cable (*2)
(Type A - A)
(sold separately)
USB cable (* 2)
(sold separately)
17-pin port
17-pin port
Fuse (1 A)
HDMI
port
HDMI cable holder
17-pin USB cable 2)(*
(sold separately)
Adapter cable (* 2) (sold separately)
Lightning to USB Cable
(supplied with iPhone with Lightning connector)
iPhone with Lightning connector (*1)
(sold separately)
iPhone
with Lightning connector (*1)
(sold separately)
Notes
· When you connect the High Speed HDMI ® Cable, use the HDMI cable holder to fix it securely.
· The iPhone needs to be connected to this navigation system via Bluetooth ® wireless technology when
you want to operate applications on the screen of the navigation system.
Note
· The iPhone needs to be connected to this navigation system via Bluetooth ® wireless technology when
you want to operate applications on the screen of the navigation system.
Connecting an iPhone with Lightning connector (for AVIC-Z150BH and AVIC-X950BH)
Connecting an iPhone with Lightning connector (for AVIC-X850BT and AVIC-X8510BT)
Black (ground)
To vehicle (metal) body
Red
To electric terminal controlled by
ignition switch (12 V DC) ON/OFF
Power supply
cable 2)(*
(sold separately)
(*1) For details concerning operations and compatibility,
refer to Operation Manual.
(*2) For details of how to connect the separately sold
HDMI/USB interface cable for iPod / iPhone (CD-IH202), refer
to the HDMI/USB interface cable for iPod / iPhone manual.
(*1) For details concerning operations and compatibility,
refer to Operation Manual.
(*2) For details of how to connect the separately sold
VGA/USB interface cable for iPod / iPhone (CD-IV202NAVI),
refer to the VGA/USB interface cable for iPod / iPhone manual.
En 9
English
Section
02
Connecting the system
Connecting an iPhone with a Lightning to 30-pin Adapter
USB interface cable for iPod / iPhone (*2)
(sold separately)
Lightning to 30-pin Adapter
(Apple Inc. products)
(sold separately)
iPhone with Lightning connector (*1)
(sold separately)
Connecting an iPhone with 30-pin connector
USB interface cable for iPod / iPhone (*2)
(sold separately)
iPhone with 30-pin connector (*1)
(sold separately)
(*1) For details concerning operations and compatibility, refer to Operation Manual.
(*2) For details of how to connect the separately sold USB interface cable for iPod / iPhone (CD-IU201N)
refer to the USB interface cable for iPod / iPhone manual.
(*1) For details concerning operations and compatibility, refer to Operation Manual.
(*2) For details of how to connect the separately sold USB interface cable for iPod / iPhone (CD-IU201N)
refer to the USB interface cable for iPod / iPhone manual.
En
10
Section
02
Connecting the system
When connecting the Android device (for AVIC-Z150BH
and AVIC-X950BH)
Notes
· When you connect the High Speed HDMI ® Cable, use the HDMI cable holder to fix it securely.
· The Android device needs to be connected to this navigation system via Bluetooth ® wireless technology
when you want to operate applications on the screen of the navigation system.
· An adapter cable will not be used if you use the MHL adapter.
Connecting an Android device with an MHL port
(*1)
For details of how to connect the
separately sold App Connectivity Kit
(CD-AH200), refer to the App
Connectivity Kit manual.
HDMI
port
USB - micro USB cable (*1)
(Type USB A - micro USB B)
(sold separately)
USB cable (*1)
(sold separately)
MHL adapter (*1)
(sold separately)
USB port
(1.6 A 5 V DC)
(CHARGE ONLY)
Connecting an Android device with an HDMI port
Notes
· When you connect the High Speed HDMI ® Cable, use the HDMI cable holder to fix it securely.
· The Android device needs to be connected to this navigation system via Bluetooth wireless technology
when you want to operate applications on the screen of the navigation system.
· An MHL adapter will not be used if you use the adapter cable.
USB port
(1.6 A 5 V DC)
(CHARGE ONLY)
USB - micro USB cable (*1)
(Type USB A - micro USB B)
(sold separately)
(*1)
For details of how to connect the
separately sold App Connectivity Kit
(CD-AH200), refer to the App
Connectivity Kit manual.
HDMI
port USB cable (*1)
(sold separately)
Adapter cable (*1)
(HDMI Type A - D)
(sold separately)
High Speed
HDMI
® Cable (*1)
(Type A - A)
(sold separately)
HDMI
cable
holder
High Speed
HDMI®
Cable (*1)
(Type A - A)
(sold separately)
HDMI
cable
holder
En 11
English
Section
02
Connecting the system
Connecting the power cord (1)
Yellow
To terminal supplied with power regardless of
ignition switch position.
Red
To electric terminal controlled by ignition
switch (12 V DC) ON/OFF.
Orange/white
To lighting switch terminal.
Black (ground)
To vehicle (metal) body.
With a two-speaker system, do not connect anything
to the speaker leads that are not connected to
speakers.
When a subwoofer is connected to this navigation
system instead of a rear speaker, change the rear
output setting in the initial setting. (Refer to
Operation Manual.) The subwoofer output of this
navigation system is monaural.
Note
White Gray
Front speakerFront speaker
White/black Gray/black
Left Right
Rear speaker or
subwoofer (4
)
Rear speaker or
subwoofer (4
)
Green Violet
Green/black Violet/black
Green Violet
When using a subwoofer of 70 W (2
), be sure to connect with violet and violet/black leads of this
navigation system. Do not connect anything with green and green/black leads.
Green/black Violet/black
Not used. Subwoofer (4
)
2
En
12
Section
02
Connecting the system
Audio source will be set to mute or attenuate, while
the following sounds will not be muted or
attenuated. For details, refer to Operation Manual.
Voice guidance of the navigation
Incoming ring tone and incoming voice of the
cellular phone that is connected to this navigation
system via Bluetooth wireless technology
Note
Yellow/black
If you use equipment with a mute
function, connect that equipment to
the Audio Mute lead. If not, keep the
Audio Mute lead free of any
connections.
Blue/white
To auto-antenna relay control terminal or
antenna booster power control terminal
(max. 300 mA 12 V DC).
If the vehicle has a glass antenna,
connect to the antenna booster power
control terminal (max. 300 mA 12 V DC).
The navigation unit
Fuse (10 A)
Power cord
RCA connector
15 cm (5-7/8 in.)
En 13
English
Section
02
Connecting the system
Connecting the power cord (2)
IMPROPER CONNECTION MAY RESULT IN SERIOUS DAMAGE OR INJURY INCLUDING
ELECTRICAL SHOCK, AND INTERFERENCE WITH THE OPERATION OF THE VEHICLE´S ANTILOCK
BRAKING SYSTEM, AUTOMATIC TRANSMISSION AND SPEEDOMETER INDICATION.
Pink (CAR SPEED SIGNAL INPUT)
The navigation system is connected here to detect the distance the vehicle travels. Always connect
the vehicle’s speed detection circuit. Failure to make this connection will increase errors in the
vehicle’s location display.
LIGHT GREEN LEAD AT POWER CONNECTOR IS
DESIGNED TO DETECT PARKED STATUS AND MUST
BE CONNECTED TO THE POWER SUPPLY SIDE OF THE
PARKING BRAKE SWITCH. IMPROPER CONNECTION
OR USE OF THIS LEAD MAY VIOLATE APPLICABLE
LAW AND MAY RESULT IN SERIOUS INJURY OR
DAMAGE.
Light green (PARKING BRAKE)
Used to detect the ON/OFF status of the parking brake. This lead must be connected to the power supply
side of the parking brake switch.
If this connection is made incorrectly or omitted, certain functions of your navigation system
will be unusable.
The position of the speed detection circuit and the position of the parking brake switch
vary depending on the vehicle model. For details, consult your authorized Pioneer dealer
or an installation professional.
Power supply side
Ground side
Parking brake switch
Connection method
Clamp the lead of the power supply
side of the parking brake switch.
Clamp firmly with needle-nosed
pliers.
WARNING
CAUTION
Note
WARNING
It is strongly suggested that the speed pulse wire be connected for accuracy of navigation
and better performance.
En
14
Section
02
Connecting the system
Violet/white (REVERSE GEAR SIGNAL INPUT)
This is connected so that the navigation system can detect
whether the vehicle is moving forwards or backwards.
Connect the violet/white lead to the lead whose voltage
changes when the shift lever is put in reverse. Unless
connected, the sensor may not detect your vehicle traveling
forward/backward properly, and thus the position of your
vehicle detected by the sensor may be misaligned from the
actual position.
When you use a rear view camera, please make
sure to connect this lead. Otherwise you cannot
switch to the rear view camera picture.
Note
The navigation unit
Power cord
En 15
English
Section
02
Connecting the system
When connecting to separately sold power amp
25 cm (9-7/8 in.)
Subwoofer outputs
(SUB WOOFER OUTPUT)
Rear outputs
(REAR OUTPUT)
Front outputs
(FRONT OUTPUT)
30 cm (11-5/8 in.)
30 cm (11-5/8 in.)
The navigation unit
Power cord
Blue/white
To system control terminal of the power amp
(max. 300 mA 12 V DC).
RCA connector
Notes
· You can change the RCA output of the subwoofer depending on your subwoofer
system. (Refer to Operation Manual.)
· The subwoofer output of this navigation system is monaural.
En
16
Section
02
Connecting the system
RCA cables
(sold separately)
System remote control
Power amp
(sold separately)
Power amp
(sold separately)
Power amp
(sold separately)
Front speaker Front speaker
Rear speaker Rear speaker
Subwoofer Subwoofer
Left Right
En 17
English
Section
02
Connecting the system
When connecting a rear
view camera
When this product is used with a rear view
camera, it is possible to automatically switch
from the video to rear view image when the
shift lever is moved to ( ).REVERSE R Rear
View mode also allows you to check what is
behind you while driving.
WARNING
USE INPUT ONLY FOR REVERSE OR MIRROR
IMAGE REAR VIEW CAMERA. OTHER USE MAY
RESULT IN INJURY OR DAMAGE.
CAUTION
! The screen image may appear reversed.
! The rear view camera is used as an aid to
keep an eye on trailers, or backing into a tight
parking spot. Do not use this function for en-
tertainment purposes.
! Objects in rear view may appear closer or
more distant than in reality.
! Please note that the image area shown by the
rear view camera may differ slightly when full-
screen images are displayed when backing
and when checking the rear of the vehicle
while moving forward.
(e.g. ND-BC6)
(sold separately)
Rear view camera
To video output
RCA cable
Brown
(REAR VIEW CAMERA IN)
RCA
connector
Power cord
The navigation unit
Violet/white
(REVERSE GEAR SIGNAL INPUT)
20 cm (7-7/8 in.)
For more details about the wiring, refer to Connecting
the power cord (2) on page 14.
Notes
! This mode is available when the rear view
camera setting is set to . (For details, On
refer to Operation Manual.)
! Connect the navigation system to the rear
view camera only. Do not connect to any
other equipment.
En
18
Section
02
Connecting the system
When connecting the
external video component
Using an AV input ( )AV1
Mini-jack extension cable
2 m (6 ft. 7 in.)
To audio outputs
The navigation unit
RCA connector
Mini-jack AV cable
(CD-RM10)
(sold separately)
Yellow Red, white
RCA cables
(sold separately)
To video output
External video
component
(sold separately)
AUX input
15 cm (5-7/8 in.)
! This mode is available when the setting of
video input 1 (AV1) is set to “On”. (For de-
tails, refer to Operation Manual.)
CAUTION
Be sure to use a mini-jack AV cable (CD-RM10)
(sold separately) for wiring. If you use other
cables, the wiring position might differ resulting
in disturbed images and sounds.
OK
GV R
L
GR V
L
L : Left audio (White)
R : Right audio (Red)
V : Video (Yellow)
G : Ground
En 19
English
Section
02
Connecting the system
Using an AV input ( )AV2
The navigation unit
Red, white
(AUDIO INPUT)
RCA cables
(sold separately)
Yellow
(VIDEO INPUT)
RCA connector
To video output To audio outputs
External video
component
(sold separately)
20 cm (7-7/8 in.)
! This mode is available when the setting of
video input 2 (AV2) is set to “On”. (For de-
tails, refer to Operation Manual.)
When connecting the rear
display
The navigation unit
RCA connector
To video input To audio inputs
Rear display with
RCA input jacks
15 cm (5-7/8 in.)
Red, white, yellow
(REAR MONITOR
OUTPUT)
RCA cables
(sold separately)
When using a rear display
connected to rear video output
WARNING
NEVER install the rear display in a location
that enables the driver to watch the video
source while driving.
This navigation system s rear video output is for
connection of a display to enable passengers in
the rear seats to watch the video source.
En
20
Section
02
Connecting the system
Precautions before
installation
CAUTION
! Never install this product in places where,
or in a manner that:
Could injure the driver or passengers if
the vehicle stops suddenly.
May interfere with the driver s opera-
tion of the vehicle, such as on the floor
in front of the driver s seat, or close to
the steering wheel or shift lever.
! Make sure there is nothing behind the
dashboard or paneling when drilling holes
in them. Be careful not to damage fuel
lines, brake lines, electronic components,
communication wires or power cables.
! When using screws, do not allow them to
come into contact with any electrical lead.
Vibration may damage wires or insulation,
leading to a short circuit or other damage
to the vehicle.
! To ensure proper installation, be sure to
use the supplied parts in the manner spe-
cified. If any parts are not supplied with
this product, use compatible parts in the
manner specified after you have the parts’
compatibility checked by your dealer. If
parts other than supplied or compatible
ones are used, they may damage internal
parts of this product or they may work
loose and the product may become de-
tached.
! It is extremely dangerous to allow cables
to become wound around the steering col-
umn or shift lever. Be sure to install this
product, its cables, and wiring away in
such so that they will not obstruct or hin-
der driving.
! Make sure that leads cannot get caught in
a door or the sliding mechanism of a seat,
resulting in a short circuit.
! Please confirm the proper function of
your vehicle s other equipment after in-
stallation of the navigation system.
! Do not install this navigation system
where it may (i) obstruct the driver s vi-
sion, (ii) impair the performance of any of
the vehicle s operating systems or safety
features, including airbags, hazard lamp
buttons or (iii) impair the driver s ability
to safely operate the vehicle.
! Install the navigation system between the
driver s seat and front passenger seat so
that it will not be hit by the driver or pas-
senger if the vehicle stops quickly.
! Never install the navigation system in
front of or next to the place in the dash-
board, door, or pillar from which one of
your vehicle s airbags would deploy.
Please refer to your vehicle s owner s
manual for reference to the deployment
area of the frontal airbags.
! Failure to follow all of these precautions
may result in serious injury or death.
To avoid electromagnetic
interference
In order to prevent interference, set the follow-
ing items as far as possible from this naviga-
tion system, other cables or leads:
! FM, AM antenna and its lead
! GPS antenna and its lead
In addition, you should lay or route each an-
tenna lead as far as possible from other anten-
na leads. Do not bind, lay or route them
together, or cross them. Electromagnetic
noise will increase the potential for errors in
the vehicle s location display.
Before installing
! Consult with your nearest dealer if installa-
tion requires drilling holes or other modifi-
cations of the vehicle.
! Before making a final installation of this
product, temporarily connect the wiring to
confirm that the connections are correct
and the system works properly.
En 21
English
Section
03
Installation
For AVIC-Z150BH users
Do not install this navigation system in a posi-
tion where the opening of the LCD panel is ob-
structed by any obstacles, such as the shift
lever. Before installing this navigation system,
be sure to leave sufficient space so that the
LCD panel does not obstruct the shift lever
when it is fully opened. This may cause inter-
ference with the shift lever, or a malfunction of
the mechanism of this navigation system.
Installing the navigation
system
Installation notes
! Do not install the navigation system in
places subject to high temperatures or hu-
midity, such as:
Places close to a heater, vent or air con-
ditioner.
Places exposed to direct sunlight, such
as on top of the dashboard.
Places that may be exposed to rain,
such as close to the door or on the vehi-
cle s floor.
! Install this navigation system in an area
strong enough to bear its weight. Choose a
position where this navigation system can
be firmly installed, and install it securely. If
this navigation system is not securely in-
stalled, the current location of the vehicle
cannot be displayed correctly.
! Install the navigation unit horizontally on a
surface within 0 to 30 degrees tolerance
(within 5 degrees to the left or right). Impro-
per installation of the unit with the surface
tilted more than these tolerances increases
the potential for errors in the vehicle s loca-
tion display, and might otherwise cause re-
duced display performance.
30°
5° 5°
! When installing, to ensure proper heat dis-
persal when using this unit, make sure you
leave ample space behind the rear panel
and wrap any loose cables so they are not
blocking the vents.
Leave ample
space 5 cm
5 cm
En
22
Section
03
Installation
!The cords must not cover the area shown
in the figure below. This is necessary to
allow the amps and navigation mechanism
to dissipate heat.
Do not cover this area.
!The semiconductor laser will be damaged
if it overheats, so don t install the naviga-
tion unit anywhere hot for instance, near
a heater outlet.
Parts supplied
Parts marked (*) are supplied with AVIC-
X950BH, AVIC-X850BT and AVIC-X8510BT.
The navigation unit Truss head screw
(5 mm × 8 mm)
(6 pcs.)
Flush surface screw
(5 mm × 9 mm)
(6 pcs.)
Screw*
(2 mm × 4 mm)
(1 pc.)
Installation using the screw holes
on the side of the navigation unit
%Fastening the navigation unit to the
factory radio-mounting bracket.
Position the navigation unit so that the brack-
ets screw holes and its screw holes are
aligned, and tighten the screws at three loca-
tions on each side.
Use either the truss head screws (5 mm ×
8 mm) or flush surface screws (5 mm ×
9 mm), depending on the shape of the brack-
et s screw holes.
If the pawl interferes with installation,
you may bend it down out of the way.
Dashboard or console
T
russ head screw or
flush surface screw
Be sure to use the
screws supplied
with this navigation
system.
Factory radio-mounting bracket
En 23
English
Section
03
Installation
Fastening the detachable faceplate
pThis description is for AVIC-X950BH, AVIC-
X850BT and AVIC-X8510BT.
If you do not plan to remove the detachable fa-
ceplate, the detachable faceplate can be fas-
tened with the supplied screw.
Screw (2 mm × 4 mm)
En
24
Section
03
Installation
Installing the GPS antenna
CAUTION
Do not cut the GPS antenna lead to shorten
it or use an extension to make it longer. Alter-
ing the antenna cable could result in a short
circuit or malfunction and permanent da-
mage to the navigation system.
Installation notes
!The antenna should be installed on a level
surface where radio waves will be blocked
as little as possible. Radio waves cannot be
received by the antenna if reception from
the satellite is blocked.
Dashboard Rear shelf
!When installing the GPS antenna inside
the vehicle, be sure to use the metal sheet
provided with your system. If this is not
used, the reception sensitivity will be poor.
!Do not cut the accessory metal sheet. This
would reduce the sensitivity of the GPS an-
tenna.
!Take care not to pull the antenna lead when
removing the GPS antenna. The magnet at-
tached to the antenna is very powerful, and
the lead may become detached.
!Do not paint the GPS antenna, as this may
affect its performance.
Parts supplied
GPS antenna Metal sheet
En 25
English
Section
03
Installation
When installing the antenna inside the vehicle (on the dashboard
or rear shelf)
WARNING
Do not install the GPS antenna over any sen-
sors or vents on the dashboard of the vehicle,
as doing so may interfere with the proper
functioning of such sensors or vents and may
compromise the ability of the metal sheet
under the GPS antenna to properly and se-
curely affix to the dashboard.
Affix the metal sheet on the surface as level as
possible where the GPS antenna faces the
window. Place the GPS antenna on the metal
sheet. (The GPS antenna is fastened with its
magnet.)
The metal sheet contains a
strong adhesive which may
leave a mark on the surface if
it is removed.
Note
Clamps
Use separately sold clamps
to secure the lead where necessary
inside the vehicle.
GPS antenna Metal sheet
Peel off the protective sheet
on the rear.
Make sure the surface is
free of moisture, dust,
grime, oil, etc., before
affixing the metal sheet.
Notes
!When attaching the metal sheet, do not cut
it into small pieces.
!Some models use window glass that does
not allow signals from GPS satellites to
pass through. On such models, install the
GPS antenna on the outside of the vehicle.
En
26
Section
03
Installation
Installing the microphone
!Install the microphone in a place where its
direction and distance from the driver
make it easiest to pick up the driver s voice.
!Make sure to connect the microphone to
the navigation system after the system is
turned off (ACC OFF).
Parts supplied
Microphone Double-sided tape
Mounting on the sun visor
1 Fit the microphone lead into the
groove.
Microphone lead
Groove
2 Attach the microphone clip to the sun
visor.
Microphone clip
Clamps
Use separately sold clamps
to secure the lead where ne-
cessary inside the vehicle.
Install the microphone on the sun visor when
it is in the up position. It cannot recognize the
driver s voice if the sun visor is in the down po-
sition.
En 27
English
Section
03
Installation
Installation on the steering column
1 Detach the microphone base from the
microphone clip by sliding the microphone
base while pressing the tab.
Microphone Tab
Microphone clip Microphone base
2 Mount the microphone on the steering
column.
Double-sided tape
Install the microphone on the
steering column, keeping it away
from the steering wheel.
Clamps
Use separately sold
clamps to secure the
lead where necessary
inside the vehicle.
Adjusting the microphone angle
The microphone angle can be adjusted.
En
28
Section
03
Installation
Précautions
Votre nouveau système de navigation et ce
manuel 30
Importantes mesures de sécurité 30
Branchement du système
Pcautions à prendre avant de brancher le
système 32
Avant d installer ce produit32
Pour éviter toute détérioration 33
Remarque concernant le fil bleu/
blanc 34
Pces fournies 34
Installation du support pour câble
HDMI® 35
Branchement du système 36
Lors de la connexion de l iPhone37
Lors de la connexion de l appareil Android
(pour AVIC-Z150BH et AVIC-X950BH) 39
Branchement du cordon d alimentation
(1) 40
Branchement du cordon d alimentation
(2) 42
Branchement d un amplificateur de
puissance vendu séparément 44
Branchement d une caméra de
rétrovisée 46
Branchement d un élément vidéo
externe 47
– ’Utilisation d une entrée AV (AV1) 47
– ’Utilisation d une entrée AV (AV2) 48
Branchement de l écran arrière48
– ’Utilisation d un écran arrre raccor
à la sortie vidéo arrre 48
Installation
Pcautions à prendre avant
l installation49
Pour éviter les parasites
électromagnétiques 49
Avant de procéder à l installation50
Pour les utilisateurs AVIC-Z150BH 50
Installation du système de navigation 50
– ’Remarques sur l installation 50
Pces fournies 51
Installation en utilisant les trous de vis
sur les côtés de cette unité de
navigation 52
Fixation de la façade amovible 52
Installation de l antenne GPS53
– ’Remarques sur l installation 53
Pces fournies 53
– ’Installation de l antenne dans le
véhicule (sur le tableau de bord ou la
lunette arrière) 54
Installation du microphone 55
Pces fournies 55
Installation sur le pare-soleil 55
Installation sur la colonne de
direction 56
– ’Réglage de l angle du microphone 57
Fr 29
Français
Sommaire
Votre nouveau système de
navigation et ce manuel
!La fonction de navigation de ce produit (et
la caméra de rétrovisée en option le cas
échéant) est uniquement destinée à vous
assister lors de la conduite de votre véhi-
cule. Elle n autorise en aucun cas un relâ-
chement de votre attention, de votre
jugement et de votre vigilance pendant la
conduite.
!N utilisez jamais ce système de navigation
en cas d urgence pour vous rendre à l hôpi-’ ’
tal ou dans une station de police. Veuillez
le cas échéant appeler le numéro d ur-
gence du service concerné.
!N utilisez pas ce système de navigation (ou
la caméra de rétrovisée en option le cas
échéant) si celui-ci risque d une façon ou
d une autre de détourner votre attention.
Observez toujours les règles de sécurité et
respectez toujours les réglementations de
la circulation routière en vigueur. Si vous
éprouvez des difficultés à utiliser le sys-
tème ou à lire l écran, garez votre véhicule
en lieu sûr et serrez le frein à main avant
d effectuer les réglages nécessaires.
!Ce manuel explique comment installer le
système de navigation dans votre véhicule.
Le fonctionnement du système de naviga-
tion est expliqué dans les manuels séparés
du système de navigation.
!N installez pas ce produit dans un endroit
où il risque (i) d entraver la visibilité du
conducteur, (ii) d altérer le fonctionnement
de certains systèmes de commande des
dispositifs de sécurité du véhicule, y
compris les airbags ou les touches de feux
de détresse, ou (iii) d empêcher le conduc-
teur de conduire le véhicule en toute sécu-
rité. Dans certains cas, il peut ne pas être
possible d installer ce produit en raison du
type de véhicule ou de la forme de l inté-
rieur du véhicule.
Importantes mesures de
sécurité
AVERTISSEMENT
Pioneer vous déconseille d installer vous-
même votre système de navigation. Ce pro-
duit est conçu pour une installation profes-
sionnelle uniquement. Nous vous
recommandons de confier l installation uni-
quement à un personnel de service Pioneer
agréé, qui a été spécialement formé et est ex-
périmenté en matière de systèmes électroni-
ques mobiles, de montage et d installation
de ce type de produit. NE TENTEZ JAMAIS
D EFFECTUER VOUS-MÊME L’ ’ENTRETIEN
OU DE DÉPANNER CE SYSTÈME DE NAVI-
GATION. L’ ’installation ou l entretien de ce
produit et des câbles de raccordement vous
expose à des décharges électriques ou autres
dangers, et risque de provoquer des détério-
rations du système de navigation non couver-
tes par la garantie.
!Lisez attentivement le contenu de ce ma-
nuel avant d installer votre système de navi-
gation.
!Conservez ce manuel à portée de main
pour vous y reporter ultérieurement.
!Tenez compte de tous les avertissements
formulés dans ce manuel et respectez soi-
gneusement les consignes.
!Dans certaines circonstances, ce système
de navigation peut afficher des informa-
tions erronées sur la position de votre véhi-
cule, la distance des objets affichés à
l écran et les directions de la boussole. En
outre, le système comporte certaines limi-
tations, notamment l incapacité de signaler
les rues à sens unique, les restrictions tem-
poraires à la circulation et les zones où la
circulation peut devenir dangereuse. Veuil-
lez vous en remettre à votre bon jugement
en fonction des conditions réelles de
conduite.
Fr
30
Section
01
Précautions
!Comme tout autre accessoire de l habita-
cle, le système de navigation ne doit pas
détourner votre attention ni nuire à la sécu-
rité de la conduite sous peine d entraîner
des blessures graves voire mortelles. Si
vous éprouvez des difficultés à utiliser le
système ou à lire l écran, effectuez les ré-
glages nécessaires après vous être garé
dans un endroit sûr.
!Veillez à toujours porter votre ceinture de
sécurité sur la route. En cas d accident, le
port de la ceinture peut réduire considéra-
blement la gravité des blessures.
!Certaines lois nationales ou gouvernemen-
tales peuvent interdire ou restreindre l em-
placement et l utilisation de ce système
dans votre véhicule. Veuillez vous confor-
mer à toutes les lois et réglementations en
vigueur concernant l utilisation, l installa-’ ’
tion et le fonctionnement de votre système
de navigation.
Fr 31
Section
Français
01
Précautions
Précautions à prendre avant
de brancher le système
AVERTISSEMENT
N essayez pas de modifier ou désactiver le
système de verrouillage du frein à main, le-
quel est installé pour votre protection. La mo-
dification ou la désactivation du système de
verrouillage du frein à main peut entraîner
des blessures graves, voire mortelles.
ATTENTION
!Si vous décidez de réaliser l installation
vous-même, et possédez une expérience
spéciale en installation d électronique au-
tomobile, veuillez suivre attentivement
toutes les étapes du manuel d installa-
tion.
!Attachez tous les fils avec des colliers ou
des serre-câbles. Ne laissez aucun fil à nu.
!Ne raccordez pas directement le fil jaune
conducteur de ce produit à la batterie du
véhicule. Si ce fil conducteur est directe-
ment raccordé à la batterie, les vibrations
du moteur peuvent finir par user les câ-
bles au niveau de la jonction avec l habita-
cle et provoquer un défaut d isolation. Si
l isolation du fil conducteur jaune se dé-
chire sous l effet du contact avec des piè-
ces métalliques, il peut en résulter un
court-circuit extrêmement dangereux.
!Il est extrêmement dangereux de laisser
les câbles s enrouler autour de la colonne
de direction ou du levier de vitesse. Assu-
rez-vous d installer ce produit, ses câbles
et les fils de telle façon qu ils n obstruent’ ’
ni ne gênent la conduite.
!Veillez à ce que la trajectoire des câbles et
des fils n interfère pas avec les pièces en
mouvement du véhicule. Fixez les câbles
de manière à les empêcher d être happés
par, notamment, le volant, le levier de vi-
tesse, le frein à main, les glissières de
siège, les portes, ou tout autre élément de
commande du véhicule.
!La trajectoire des fils ne doit pas être ex-
posée à des températures élevées. Si l iso-
lation chauffe, les fils risquent d être
endommagés, ce qui peut entraîner un
court-circuit ou un dysfonctionnement, et
endommager de manière irrémédiable le
produit.
!Ne coupez pas le câble de l antenne GPS
et n utilisez pas de rallonge. Une telle mo-
dification pourrait provoquer un court-cir-
cuit ou un dysfonctionnement.
!Ne raccourcissez aucun fil conducteur.
Vous risqueriez autrement de provoquer
un dysfonctionnement du circuit de pro-
tection (porte-fusibles, résistance de fu-
sible ou filtre, etc.).
!N utilisez jamais le cordon d alimentation’ ’
du système d alimentation pour raccorder
d autres appareils électriques. La capacité
du cordon serait dépassée, ce qui provo-
querait une surchauffe.
Avant d installer ce produit
!Utilisez cet appareil uniquement avec une
batterie de 12 V, avec pôle négatif à la
masse. Sinon, cela pourrait entraîner un in-
cendie ou un mauvais fonctionnement.
!Afin d éviter tout risque de court-circuit, dé-
branchez le câble de la borne négative ( )
de la batterie avant de commencer la pose.
Fr
32
Section
02
Branchement du système
Pour éviter toute
détérioration
AVERTISSEMENT
!Utilisez des haut-parleurs de plus de 50 W
(valeur de sortie) et avec une impédance
comprise entre 4 et 8W W. Nutilisez pas de
haut-parleurs 1 Wà 3 Wavec cet appareil.
!Le câble noir est celui de la mise à la terre.
Lors de l installation de cette unité ou de
l amplificateur (vendu séparément),
connectez toujours le fil de mise à la terre
en premier. Assurez-vous que le fil de
mise à la terre est correctement connec
aux pièces métalliques du châssis de la
voiture. Le fil de mise à la terre de l ampli-
ficateur et celui de cette unité ou de tout
autre appareil doivent être connectés sé-
parément à la voiture avec des vis diffé-
rentes. Si les vis du fil de mise à la terre
sont desserrées ou tombent, il pourrait en
résulter un incendie ou un dysfonctionne-
ment.
*1Non fourni avec cette unité.
*1
Fil de mise à la terre Amplificateur
Autres appareils
(Autre appareil
électronique dans
la voiture)
Pièces métalliques
du châssis de
la voiture
!Lors du remplacement du fusible, veillez à
utiliser seulement un fusible du calibre in-
diqué sur ce produit.
!Pour débrancher un connecteur, tirez le
connecteur proprement dit et non son fil
pour éviter de l arracher.
!Ce produit ne peut pas être installé dans
un hicule qui ne possède pas de position
ACC (accessoire) sur le commutateur d al-
lumage.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
Position ACC Pas de position
ACC
!Pour éviter les courts-circuits, recouvrez les
fils déconnectés de ruban isolant. Il est par-
ticulièrement important d isoler tous les fils
conducteurs de haut-parleurs non utilisés
pour éviter tout risque de court-circuit.
!Raccordez les connecteurs de même cou-
leur au port de couleur correspondant,
c est-à-dire le connecteur bleu au port bleu,
le noir au noir, etc.
!Pour raccorder l amplificateur de puis-
sance à d autres unités, veuillez vous repor-
ter au mode d emploi concerné.
!Un circuit BPTL unique étant employé, ne
reliez pas directement l extrémité du fil
conducteur de haut-parleur ou ne reliez*
pas les extrémités des fils conducteurs de
haut-parleur ensemble. Veillez à relier*
l extrémité du fil conducteur de haut-par-*
leur à l extrémité du fil conducteur de*
haut-parleur de ce système de navigation.
Fr 33
Section
Français
02
Branchement du système
Remarque concernant le fil
bleu/blanc
!Lorsque le commutateur d allumage est
sur Marche (ACC ON), un signal de
commande est émis par le biais du fil bleu/
blanc. Raccordez-le à une borne de
commande à distance du système d ampli-
ficateur de puissance externe, à la prise de
commande de relais de l antenne automa-
tique du véhicule ou au terminal de
commande d alimentation de l amplifica-’ ’
teur d antenne (max. 300 mA 12 VCC). Le si-
gnal de commande est émis par le biais du
fil bleu/blanc, même si la source audio est
désactivée.
!Assurez-vous de ne pas utiliser ce fil
comme câble d alimentation pour les am-
plificateurs de puissance externes. Une
telle connexion pourrait causer un appel de
courant excessif et un mauvais fonctionne-
ment.
!Assurez-vous de ne pas utiliser ce fil
comme câble d alimentation pour l an-’ ’
tenne automatique ou l amplificateur d an-’ ’
tenne. Une telle connexion pourrait causer
un appel de courant excessif et un mauvais
fonctionnement.
Pièces fournies
Les pièces marquées d un astérisque (*) sont
fournies avec AVIC-Z150BH et AVIC-X950BH.
Unité de navigation Cordon d alimentation
Connecteur RCA Antenne GPS
Microphone Support pour câble
HDMI*
Rallonge pour câble
mini-jack
Fr
34
Section
02
Branchement du système
Installation du support
pour câble HDMI ®
1 Insérez la languette inférieure du sup-
port pour câble HDMI dans la fente de ce
produit.
Fente
Languette
2 Insérez les deux languettes supérieures
dans ce produit en enfonçant le support
pour câble HDMI.
Languettes
p Utilisez le support pour câble HDMI lorsque
vous connectez ce produit avec le Kit de
connexion aux applications (CD-AH200), le
câble d interface HDMI/USB pour iPod /
iPhone (CD-IH202) ou le câble d interface
VGA/USB pour iPod / iPhone (CD-IV202NA-
VI) vendus séparément.
p Ne tenez pas le support serré ni n utilisez la
force lors du retrait ou de la fixation du
panneau.
Fr 35
Section
Français
02
Branchement du système
Branchement du système
Unité de navigation
Entrée à distance câblée
Veuillez vous reporter au mode d’emploi
de l’adaptateur de commande à distance
câblés (vendus séparément).
Syntonisateur pour véhicule SiriusXM Connect
Veuillez consulter le mode d’emploi pour le
Syntonisateur pour véhicule SiriusXM Connect
(vendu séparément).
3,55 m
Antenne GPS
Prise d’antenne
Antenne du véhicule
Microphone
4 m
AVERTISSEMENT
· Pour éviter le risque d’un accident et une possible infraction aux lois en vigueur,
ce produit ne doit en aucun cas être utilisé alors que le véhicule roule sauf à des
fins de navigation. Par ailleurs, les écrans arrière ne doivent pas être placés là où
ils pourraient représenter une distraction pour le conducteur.
· Dans certains pays, le fait de regarder des images sur un afficheur dans une
voiture est illégal, même s’il s’agit d’autres personnes que le conducteur. Lorsqu’il
existe de telles règles, vous devez vous y conformer et la source vidéo de ce
produit ne doit pas être utilisée.
Fr
36
Section
02
Branchement du système
Lors de la connexion de l iPhone
Adaptateur Lightning vers VGA
(produits Apple Inc.)
(vendu séparément)
Adaptateur Lightning AV numérique
(produits Apple Inc.)
(vendu séparément)
Câble Lightning vers USB
(fourni avec l’iPhone avec connecteur Lightning)
Câble HDMI® haute vitesse (*2)
(Type A - A)
(vendu séparément)
Câble USB (*2)
(vendu séparément)
Port 17
broches
Port 17 broches
Fusible (1 A)
Port
HDMI
Support pour câble HDMI
Câble USB 17 broches (*2)
(vendu séparément)
Câble pour adaptateur (*2) (vendu séparément)
Câble Lightning vers USB
(fourni avec l’iPhone avec connecteur Lightning)
iPhone avec connecteur Lightning (*1)
(vendu séparément)
iPhone avec
connecteur Lightning (*1)
(vendu séparément)
Remarques
· Lorsque vous connectez le câble HDMI ® haute vitesse, utilisez le support pour câble HDMI pour bien le
maintenir en place.
· L’iPhone doit être connecté à ce système de navigation via la technologie sans fil Bluetooth ® lorsque
vous souhaitez commander les applications sur l’écran du système de navigation.
Remarque
· L’iPhone doit être connecté à ce système de navigation via la technologie sans fil Bluetooth ® lorsque
vous souhaitez commander les applications sur l’écran du système de navigation.
Connexion d’un iPhone avec connecteur Lightning (pour AVIC-Z150BH et AVIC-X950BH)
Connexion d’un iPhone avec connecteur Lightning (pour AVIC-X850BT et AVIC-X8510BT)
Noir (terre)
Vers la carrosserie (en tal) du véhicule
Rouge
Vers la borne électrique commandée par
le commutateur d’allumage (12 VCC) ON/OFFCâble
d’alimentation (*2)
(vendu séparément)
(*1) Pour en savoir plus sur le fonctionnement et la compatibilité,
reportez-vous au Manuel de fonctionnement.
(*2) Pour en savoir plus sur la connexion du câble d’interface
HDMI/USB pour iPod / iPhone (CD-IH202) vendu
séparément, consultez le manuel l’accompagnant.
(*1) Pour en savoir plus sur le fonctionnement et la compatibilité,
reportez-vous au Manuel de fonctionnement.
(*2) Pour en savoir plus sur la connexion du câble d’interface
VGA/USB pour iPod / iPhone (CD-IV202NAVI) vendu
sépament, consultez le manuel l’accompagnant.
Fr 37
Section
Français
02
Branchement du système
Connexion d’un iPhone avec Adaptateur Lightning vers 30 broches
Adaptateur Lightning vers 30 broches
(produits Apple Inc.)
(vendu séparément)
iPhone avec connecteur Lightning (* 1)
(vendu séparément)
Connexion d’un iPhone avec connecteur à 30 broches
Câble d’interface USB pour iPod / iPhone (*2)
(vendu séparément)
Câble d’interface USB pour iPod / iPhone (*2)
(vendu séparément)
iPhone avec connecteur à 30 broches (*1)
(vendu séparément)
(*1) Pour en savoir sur le fonctionnement et la compatibilité, reportez-vous au Manuel de fonctionnement.
(*2) Pour en savoir plus sur la connexion du câble d’interface USB pour iPod / iPhone (CD-IU201N) vendu
séparément, consultez le manuel l’accompagnant.
(*1) Pour en savoir sur le fonctionnement et la compatibilité, reportez-vous au Manuel de fonctionnement.
(*2) Pour en savoir plus sur la connexion du câble d’interface USB pour iPod / iPhone (CD-IU201N) vendu
séparément, consultez le manuel l’accompagnant.
Fr
38
Section
02
Branchement du système
Lors de la connexion de l appareil Android (pour AVIC-
Z150BH et AVIC-X950BH)
Remarques
· Lorsque vous connectez le câble HDMI ® haute vitesse, utilisez le support pour câble HDMI pour bien le
maintenir en place.
· L’appareil Android doit être connecté à ce système de navigation via la technologie sans fil Bluetooth ® si
vous souhaitez commander les applications sur l’écran du système de navigation.
· Un câble pour adaptateur ne sera pas utilisé si vous utilisez l’adaptateur MHL.
Connexion d’un appareil Android à un port MHL
(*1)
Pour en savoir plus sur la manière de
connecter le Kit de connexion aux
applications vendu séparément
(CD-AH200), reportez-vous au manuel du
Kit de connexion aux applications.
Port
HDMI
Câble USB - micro USB (*1)
(Type USB A - micro USB B)
(vendu séparément)
Câble USB (*1)
(vendu séparément)
Adaptateur MHL (*1)
(vendu séparément)
Port USB
(1,6 A 5 VCC)
(CHARGE ONLY)
Connexion d’un appareil Android à un port HDMI
Remarques
· Lorsque vous connectez le câble HDMI ® haute vitesse , utilisez le support pour câble HDMI pour bien le
maintenir en place.
· L’appareil Android doit être connecté à ce système de navigation via la technologie sans fil Bluetooth si
vous souhaitez commander les applications sur l’écran du système de navigation.
· Un adaptateur MHL ne sera pas utilisé si vous utilisez le câble pour adaptateur.
Port USB
(1,6 A 5 VCC)
(CHARGE ONLY)
Câble USB - micro USB (*1)
(Type USB A - micro USB B)
(vendu séparément)
(*1)
Pour en savoir plus sur la manière de
connecter le Kit de connexion aux
applications vendu séparément (CD-AH200),
reportez-vous au manuel du Kit de
connexion aux applications.
Port
HDMI Câble USB (*1)
(vendu séparément)
Câble pour adaptateur (*1)
(HDMI type A - D)
(vendu séparément)
Câble HDMI®
haute vitesse (*1)
(Type A - A)
(vendu
séparément)
Support
pour
câble
HDMI
Câble HDMI®
haute vitesse (*1)
(Type A - A)
(vendu
séparément)
Support
pour
câble
HDMI
Fr 39
Section
Français
02
Branchement du système
Branchement du cordon d alimentation (1)
Jaune
Vers la borne alimentée en électricité indépendamment de la
position du contacteur d’allumage.
Rouge
Vers la borne électrique contrôlée par le
contacteur d’allumage (12 VCC) ON/OFF.
Orange/blanc
Vers la borne de permutation de l’éclairage.
Noir (terre)
Vers le châssis du véhicule (métallique).
Avec un système à deux haut-parleurs, ne connectez
rien sur les fils du haut-parleur n’étant pas connectés
aux haut-parleurs.
Lorsqu’un haut-parleur d’extrêmes graves est raccordé
à ce système de navigation à la place d’un haut-parleur
arrière, changez le réglage de sortie arrière dans les
réglages initiaux. (Reportez-vous au Manuel de
fonctionnement.) La sortie du haut-parleur d’extrêmes
graves de ce système de navigation est en mono.
Blanc Gris
Haut-parleur
avant
Haut-parleur
avant
Blanc/noir Gris/noir
Gauche Droite
Haut-parleur
arrière ou
Haut-parleur
d’extrêmes graves
(4 Ω)
Haut-parleur
arrière ou
Haut-parleur
d’extrêmes graves
(4 Ω)
Vert Violet
Vert/noir Violet/noir
Vert Violet
Lorsque vous utilisez un haut-parleur d’extrêmes graves de 70 W (2 Ω), veillez à raccorder les fils
violets et violets/noirs de ce système de navigation. Ne raccordez rien aux fils verts et verts/noirs.
Vert/noir Violet/noir
Non utilisé Haut-parleur
d’extrêmes graves
(4 ) x 2
Remarque
Fr
40
Section
02
Branchement du système
La source audio sera coupée ou atténuée, alors
que les sons suivants ne seront ni coupés, ni
atténués. Pour en savoir plus, reportez-vous au
Manuel de fonctionnement.
— Guidage vocal de la navigation
— Sonnerie entrante et voix entrante du téléphone
portable raccordé à ce système de navigation via
la technologie sans fil Bluetooth
Jaune/noir
Si vous utilisez un appareil avec une
fonction de sourdine, raccordez-le au
fil conducteur Sourdine audio. Le cas
contraire, ne raccordez rien à ce fil.
Bleu/blanc
Vers la prise de commande de relais de l’antenne
automatique ou le terminal de commande d’alimentation
de l’amplificateur d’antenne (max. 300 mA 12 VCC).
Si le véhicule a une antenne de pare-brise, connectez le
câble à la prise d’alimentation de l’amplificateur
d’antenne (max. 300 mA, 12 VCC).
Unité de navigation
Fusible (10 A)
Cordon
d’alimentation
Connecteur RCA
15 cm
Remarque
Fr 41
Section
Français
02
Branchement du système
Branchement du cordon d alimentation (2)
UN RACCORDEMENT INCORRECT PEUT ÊTRE À L’ORIGINE DE DÉGÂT OU BLESSURE GRAVE,
NOTAMMENT UNE ÉLECTROCUTION ET UNE INTERFÉRENCE AVEC LE FONCTIONNEMENT DU
SYSTÈME DE FREINAGE ANTIBLOCAGE DU VÉHICULE, DE LA BOÎTE DE VITESSES AUTOMATIQUE ET
DE L’AFFICHAGE DU COMPTEUR DE VITESSE.
Rose (CAR SPEED SIGNAL INPUT)
Le système de navigation est branché ici pour détecter la distance parcourue par le véhicule.
Raccordez toujours le circuit de détection de vitesse du véhicule sous peine d’augmenter les
erreurs d’affichage de l’emplacement du véhicule.
LE FIL VERT CLAIR DU CONNECTEUR
D’ALIMENTATION EST CONÇU POUR DÉTECTER
L’ÉTAT DE STATIONNEMENT ET DOIT ÊTRE BRANCHÉ
CÔTÉ ALIMENTATION ÉLECTRIQUE DU CONTACTEUR
DE FREIN À MAIN. UNE CONNEXION OU UNE
UTILISATION INAPPROPRIÉE DE CE FIL PEUT ÊTRE
ILLÉGALE À L’ÉGARD DE LA LOI EN VIGUEUR ET
RISQUE D’ENTRAÎNER DES BLESSURES SÉRIEUSES OU
DES DOMMAGES.
Vert clair (PARKING BRAKE)
Utilisé pour détecter le statut ON/OFF du frein à main. Ce fil conducteur doit être raccordé au côté
alimentation électrique du contacteur de frein à main.
Si ce raccordement est mal exécuté ou omis, certaines fonctions de votre système de navigation
ne seront pas utilisables.
La position du circuit de détection de vitesse et la position du contacteur de frein à main
varient selon le modèle du véhicule. Pour plus de détails, contactez votre revendeur
Pioneer agréé ou un installateur professionnel.
Côté alimentation
électrique
Côté terre
Contacteur de frein à main
Méthode de raccordement
Fixez le fil du côté alimentation
électrique du contacteur de frein à
main.
Fixez solidement les pinces à bec
fin.
AVERTISSEMENT
ATTENTION
Remarque
AVERTISSEMENT
Il est vivement recommandé de raccorder le câble d’impulsion de vitesse pour une
navigation précise et de meilleures performances.
Fr
42
Section
02
Branchement du système
Violet/blanc (REVERSE GEAR SIGNAL INPUT)
Ceci est raccordé pour que le système de navigation puisse détecter
si le véhicule avance ou recule. Raccordez le fil conducteur
violet/blanc au fil dont la tension change lorsque le pignon de
marche arrière est engagé. Sans ce raccordement, le capteur risque
de ne pas pouvoir détecter correctement le déplacement en marche
avant/arrière de votre véhicule, et par conséquent la position de votre
véhicule telle qu’elle est détectée par le capteur risque de ne pas être
alignée sur votre position réelle.
Lorsque vous utilisez une caméra de rétrovisée,
veillez à raccorder ce fil sous peine de ne pas
pouvoir afficher l’image de la caméra de
rétrovisée.
Remarque
Unité de navigation
Cordon d’alimentation
Fr 43
Section
Français
02
Branchement du système


Specyfikacje produktu

Marka: Pioneer
Kategoria: Nawigacja
Model: AVIC-X950BH

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Pioneer AVIC-X950BH, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Nawigacja Pioneer

Instrukcje Nawigacja

Najnowsze instrukcje dla Nawigacja

A-Rival

A-Rival Teasi One Instrukcja

15 Stycznia 2025
Navman

Navman F47M Instrukcja

5 Października 2024
Navman

Navman 4000 Instrukcja

5 Października 2024