Instrukcja obsługi Pioneer AVH-P6850DVD

Pioneer Receiver AVH-P6850DVD

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pioneer AVH-P6850DVD (44 stron) w kategorii Receiver. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/44
English Español Português (B)
AVH-P6850DVD
This product conforms to new cord colors.
Los colores de los cables de este producto se confor-
man con un nuevo código de colores.
As cores dos fios deste produto seguem um novo padrão
de cores.
INSTALLATION MANUAL
INSTALLATION MANUAL
1
Contents
Connecting the Units ................................ 1
Connecting the power cord .............................. 3
When connecting to separately sold power
amp ............................................................ 5
When connecting with a rear view camera ...... 7
When connecting with a multi-channel
processor .................................................... 8
When connecting with Vehicle Dynamics
Processor and an iPod adapter .................... 9
When connecting with Vehicle Dynamics
Processor and a Bluetooth adapter .......... 10
When connecting the external video
component and the display ...................... 11
Installation ................................................ 12
Installing the remote control unit .................... 12
Installation using the screw holes
on the side of this unit .............................. 13
WARNING
To avoid the risk of accident and the potential
violation of applicable laws, the front DVD or TV
(sold separately) feature should never be used
while the vehicle is being driven. Also, Rear
Displays should not be in a location where it is a
visible distraction to the driver.
In some countries or states the viewing of images
on a display inside a vehicle even by persons
other than the driver may be illegal. Where such
regulations apply, they must be obeyed and this
unit's DVD features should not be used.
CAUTION:
PIONEER does not recommend that
you install or service your display your-
self. Installing or servicing the product
may expose you to risk of electric shock
or other hazards. Refer all installation
and servicing of your display to autho-
rized Pioneer service personnel.
Secure all wiring with cable clamps or
electrical tape. Do not allow any bare
wiring to remain exposed.
Do not drill a hole into the engine com-
partment to connect the yellow lead of
the unit to the vehicle battery. Engine
vibration may eventually cause the insu-
lation to fail at the point where the wire
passes from the passenger compartment
into the engine compartment. Take
extra care in securing the wire at this
point.
It is extremely dangerous to allow the
display lead to become wound around
the steering column or gearshift. Be sure
to install the display in such a way that
it will not obstruct driving.
Make sure that wires will not interfere
with moving parts of the vehicle, such as
the gearshift, parking brake or seat slid-
ing mechanism.
Do not shorten any leads. If you do, the
protection circuit may fail to work
properly.
WARNING
LIGHT GREEN LEAD AT POWER CONNEC-
TOR IS DESIGNED TO DETECT PARKED
STATUS AND MUST BE CONNECTED TO
THE POWER SUPPLY SIDE OF THE PARK-
ING BRAKE SWITCH. IMPROPER CONNEC-
TION OR USE OF THIS LEAD MAY VIO-
LATE APPLICABLE LAW AND MAY
RESULT IN SERIOUS INJURY OR DAMAGE.
Connecting the Units
English Español Deutsch Français Italiano Nederlands
2
Note:
This unit is for vehicles with a 12-volt battery and
negative grounding. Before installing it in a recre-
ational vehicle, truck, or bus, check the battery
voltage.
To avoid shorts in the electrical system, be sure to
disconnect the battery cable before beginning
installation.
Refer to the owner’s manual for details on
connecting the power amp and other units, then
make connections correctly.
Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake
and seat rails. Do not route wiring in places that
get hot, such as near the heater outlet. If the insu-
lation of the wiring melts or gets torn, there is a
danger of the wiring short-circuiting to the vehicle
body.
Don’t pass the yellow lead through a hole into the
engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.
Never feed power to other equipment by cutting
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.
When replacing the fuse, be sure to only use a
fuse of the rating prescribed on the fuse holder.
Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded or
the left and right speaker leads are common.
If the RCA pin jack on the unit will not be used,
do not remove the caps attached to the end of the
connector.
Speakers connected to this unit must be high-
power with minimum rating of 50 W and imped-
ance of 4 to 8 ohms. Connecting speakers with
output and/or impedance values other than those
noted here may result in the speakers catching
fire, emitting smoke or becoming damaged.
When this product’s source is switched ON, a
control signal is output through the blue/white
lead. Connect to an external power amp’s system
remote control or the car’s Auto-antenna relay
control terminal (max. 300 mA 12 V DC). If the
car features a glass antenna, connect to the anten-
na booster power supply terminal.
When an external power amp is being used with
this system, be sure not to connect the blue/white
lead to the amp’s power terminal. Likewise, do
not connect the blue/white lead to the power ter-
minal of the auto-antenna. Such connection could
cause excessive current drain and malfunction.
To avoid short-circuit, cover the disconnected
lead with insulating tape. Insulate the unused
speaker leads without fail. There is a possibility of
a short-circuit if the leads are not insulated.
To prevent incorrect connection, the input side of
the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same col-
ors correctly.
This unit cannot be installed in a vehicle that
does not have an ACC (accessory) position on
the ignition switch. (Fig. 1)
Fig. 1
The black lead is ground. Please ground this lead
separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the
ground becomes detached, there is a risk of dam-
age to the products or fire.
No ACC positionACC position
O
N
S
T
A
R
T
O
F
F
A
C
C
O
N
S
T
A
R
T
O
F
F
Cords for this product and those for other prod-
ucts may be different colors even if they have
the same function. When connecting this product
to another product, refer to the supplied manuals
of both products and connect cords that have the
same function.

Specyfikacje produktu

Marka: Pioneer
Kategoria: Receiver
Model: AVH-P6850DVD

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Pioneer AVH-P6850DVD, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Receiver Pioneer

Pioneer

Pioneer GM-D500M Instrukcja

6 Października 2024
Pioneer

Pioneer VSX-535 Instrukcja

4 Października 2024
Pioneer

Pioneer DEH-1050E Instrukcja

4 Września 2024
Pioneer

Pioneer VSX-834 Instrukcja

3 Września 2024
Pioneer

Pioneer MVH-200EX Instrukcja

31 Sierpnia 2024
Pioneer

Pioneer GM-A4604 Instrukcja

26 Sierpnia 2024

Instrukcje Receiver

Najnowsze instrukcje dla Receiver

Kicker

Kicker PXA500.1 Instrukcja

6 Października 2024
Kicker

Kicker KXA400.1 Instrukcja

6 Października 2024
Kicker

Kicker IQ1000.1 Instrukcja

6 Października 2024
Fosi Audio

Fosi Audio E10 Instrukcja

6 Października 2024
Ferguson

Ferguson i400s Instrukcja

6 Października 2024
Vonyx

Vonyx VXA-1500 Instrukcja

6 Października 2024
CSL

CSL 301094 Instrukcja

6 Października 2024
DataVideo

DataVideo HBT-18 Instrukcja

6 Października 2024