Instrukcja obsługi Pioneer AVH-P6450

Pioneer odbiornik AVH-P6450

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pioneer AVH-P6450 (76 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/76
AVH-P6450CD
AVH-P6450
ENGLISH ESPAÑOL
PORTUGUÊS (B)
This product conforms to new cord colors.
Los colores de los cables de este producto se confor-
man con un nuevo código de colores.
As cores dos fios deste produto seguem um novo
padrão de cores.
INSTALLATION MANUAL
INSTALLATION MANUAL
WOÐdF«
u« l “UN'« «c¼ r−M¹Æ…b¹b'« „öÝô« Ê«
1
Contents
Connecting the Units ................................ 1
Connecting the power cord (1) .......................... 3
Connecting the power cord (2) .......................... 5
Connecting the system (A) ................................ 6
Connecting the system (B) ................................ 7
VIDEO Input / Output Connection .................. 8
Installation .................................................. 9
DIN Front/Rear-mount ...................................... 9
DIN Front-mount .............................................. 9
DIN Rear-mount .............................................. 11
CAUTION
• PIONEER does not recommend that
you install or service your display your-
self. Installing or servicing the product
may expose you to risk of electric shock
or other hazards. Refer all installation
and servicing of your display to autho-
rized Pioneer service personnel.
• Secure all wiring with cable clamps or
electrical tape. Do not allow any bare
wiring to remain exposed.
• Do not drill a hole into the engine com-
partment to connect the yellow lead of
the unit to the vehicle battery. Engine
vibration may eventually cause the insu-
lation to fail at the point where the wire
passes from the passenger compartment
into the engine compartment. Take
extra care in securing the wire at this
point.
• It is extremely dangerous to allow the
display lead to become wound around
the steering column or gearshift. Be sure
to install the display in such a way that
it will not obstruct driving.
• Make sure that wires will not interfere
with moving parts of the vehicle, such as
the gearshift, parking brake or seat slid-
ing mechanism.
• Do not shorten any leads. If you do, the
protection circuit may fail to work
properly.
Connecting the Units
2
ENGLISH ESPAÑOL DEUTSCH FRANÇAIS ITALIANO NEDERLANDS
Note:
• This unit is for vehicles with a 12-volt battery and
negative grounding. Before installing it in a recre-
ational vehicle, truck, or bus, check the battery
voltage.
• To avoid shorts in the electrical system, be sure to
disconnect the battery cable before beginning≠
installation.
• Refer to the owner’s manual for details on
connecting the power amp and other units, then
make connections correctly.
• Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
• Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake,
and seat rails. Do not route wiring in places that
get hot, such as near the heater outlet. If the insu-
lation of the wiring melts or gets torn, there is a
danger of the wiring short-circuiting to the vehicle
body.
• Don’t pass the yellow lead through a hole into the
engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.
• Never feed power to other equipment by cutting
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.
• When replacing fuse, be sure to use only fuse of
the rating prescribed on the fuse holder.
• Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded or
the left and right speaker leads are common.≠
• If the RCA pin jack on the unit will not be used,
do not remove the caps attached to the end of the
connector.
• Speakers connected to this unit must be high-
power types with minimum rating of 50 W and
impedance of 4 to 8 ohms. Connecting speakers
with output and/or impedance values other than
those noted here may result in the speakers catch-
ing fire, emitting smoke, or becoming damaged.
• When this product’s source is switched ON, a
control signal is output through the blue/white
lead. Connect to an external power amp’s system
remote control or the car’s Auto-antenna relay
control terminal (max. 300 mA 12 V DC). If the
car features a glass antenna, connect to the anten-
na booster power supply terminal.
• When an external power amp is being used with
this system, be sure not to connect the blue/white
lead to the amp’s power terminal. Likewise, do
not connect the blue/white lead to the power ter-
minal of the auto-antenna. Such connection could
cause excessive current drain and malfunction.
• To avoid short-circuiting, cover the disconnected
lead with insulating tape. Especially, insulate the
nused speaker leads without fail. There is a possi-
bility of short-circuiting if the leads are not insu-
lated.
• To prevent incorrect connection, the input side of
the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same col-
ors correctly.
• If this unit is installed in a vehicle that does not
have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be connect-
ed to a terminal coupled with ignition switch
ON/OFF operations. If this is not done, the vehi-
cle battery may be drained when you are away
from the vehicle for several hours. (Fig.1)
Fig. 1
• The black lead is ground. Please ground this lead
separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the
ground becomes detached, there is a risk of dam-
age to the products or fire.
No ACC positionACC position
O
N
S
T
A
R
T
O
F
F
A
C
C
O
N
S
T
A
R
T
O
F
F
• Cords for this product and those for other prod-
ucts may be different colors even if they have
the same function. When connecting this product
to another product, refer to the supplied
Installation manuals of both products and con-
nect cords that have the same function.

Specyfikacje produktu

Marka: Pioneer
Kategoria: odbiornik
Model: AVH-P6450

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Pioneer AVH-P6450, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje odbiornik Pioneer

Pioneer

Pioneer SX-303RDS Instrukcja

10 Października 2024
Pioneer

Pioneer GM-D500M Instrukcja

6 Października 2024
Pioneer

Pioneer VSX-535 Instrukcja

4 Października 2024
Pioneer

Pioneer A-10EB Instrukcja

23 Września 2024
Pioneer

Pioneer VSX-531D-B Instrukcja

21 Września 2024
Pioneer

Pioneer DMH-342EX Instrukcja

21 Września 2024
Pioneer

Pioneer DMH-340EX Instrukcja

17 Września 2024
Pioneer

Pioneer AVH-A215BT Instrukcja

14 Września 2024
Pioneer

Pioneer A-10 Instrukcja

14 Września 2024
Pioneer

Pioneer DEH-1550B Instrukcja

14 Września 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Marantz

Marantz SR-8000 Instrukcja

15 Stycznia 2025
AKAI

AKAI AM-32 Instrukcja

15 Stycznia 2025
Peavey

Peavey CKd 608 Instrukcja

15 Stycznia 2025
OSD Audio

OSD Audio Nero HTX4150 Instrukcja

14 Stycznia 2025
S.M.S.L

S.M.S.L PA200 Instrukcja

14 Stycznia 2025
Pyle

Pyle PFMRA340BB.5 Instrukcja

13 Stycznia 2025
Wavtech

Wavtech link700.4plus Instrukcja

13 Stycznia 2025
Behringer

Behringer NU6000DSP Instrukcja

12 Stycznia 2025
Denon

Denon DRA-935R Instrukcja

12 Stycznia 2025
Kenwood

Kenwood KMM-BT508DAB Instrukcja

12 Stycznia 2025