Instrukcja obsługi Peerless-AV Xtreme XHB652

Peerless-AV monitor Xtreme XHB652

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Peerless-AV Xtreme XHB652 (28 stron) w kategorii monitor. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/28
12019-02-07 #:180-9127-2 (2020-03-16)
XTREME HIGH BRIGHT OUTDOOR DISPLAY
User Guide
ENG
22019-02-07 #:180-9127-2 (2020-03-16)
SYSTEM INSTALLATION AND ELECTRICAL REQUIREMENTS
Electrical Code
Note: To the display system installer: This reminder is provided to call attention to Article 820-44 of
the National Electric Code that provides guidelines for proper grounding and, in particular, species
that the cable ground shall be connected to the grounding system of the facility. Outlet shall be
installed near the equipment and shall be easily accessible.
Antenna discharge unit
(NEC Section 810-20)
NEC National Electric Code
Ground clamp
Electric service
equipment
Ground clamps
Power service grounding
electrode system
(NEC Art 250 Part H)
Grounding conductors
(NEC Section 810-21)
Antenna lead-in wire
Power Source
The display must be connected to a mains socket outlet with a protective grounding connection.
The mains plug is used as the disconnect device and shall remain readily accessible.
Electrical installation shall be in accordance with the applicable parts of Chapter 8 of ANSI/NFPA70.
An outdoor antenna should not be located near overhead electrical lines or any electrical circuits.
If an outside antenna is connected to the receiver, conrm that the antenna system is grounded to
protect against voltage surges and built up static charges. Section 810 of the National Electric Code,
ANSI/NFPA No 70-1984, provides information with respect to proper grounding for the mast and
supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
connectors, location of antenna discharge unit, connection to grounding electrodes and requirements
for the grounding electrode.
This display operates on 100-240 volts 50-60 Hz, AC current. Insert the power cord into a 120 volt
60 Hz outlet. Never connect the display to direct current or anything other than the specied voltage.
To prevent electric shock from the display, do not use with an extension cord, receptacle, or other
outlet unless the blades and ground terminal can be fully inserted to prevent blade exposure.
All secondary lines must be routed through grounded conduit and kept separate from AC line.
Note: Installation shall incorporate UL Listed external surge protection rated 2500 Vpk or less, for 150
to 300 Vac mains, installed in accordance with Article 285 of ANSI/NFPA 70 or applicable local codes.
32019-02-07 #:180-9127-2 (2020-03-16)
Relevant Information
Record your display's model and serial number here for future reference. Keep this user manual in an
accessible location in the event service is required.
Note: Your display's serial number can be found on the box and underneath the rear cover plate.
Model Number ____________________________________
Serial Number ____________________________________
FCC CAUTION
To assure continued compliance and possible undesirable interference, ferrite cores may be used
when connecting this display to video equipment; maintain at least 400mm (15.75 inches) spacing to
other peripheral devices.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with these instructions,
may cause harmful interference to radio communications; however, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o󰀨
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit di󰀨erent from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio/display technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause
undesired operation.


Specyfikacje produktu

Marka: Peerless-AV
Kategoria: monitor
Model: Xtreme XHB652

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Peerless-AV Xtreme XHB652, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje monitor Peerless-AV

Instrukcje monitor

Najnowsze instrukcje dla monitor

Acer

Acer EB321HQUDbmidphx Instrukcja

15 Października 2024
Bauhn

Bauhn APMTR-0624 Instrukcja

15 Października 2024
Acer

Acer KA270H Instrukcja

14 Października 2024
Acer

Acer K272HUL Dbmidpx Instrukcja

14 Października 2024
NEC

NEC E424 Instrukcja

14 Października 2024
LG

LG UltraGear 32GS85Q Instrukcja

14 Października 2024
LG

LG UltraGear 27GS85Q Instrukcja

14 Października 2024
Acer

Acer EK220QB Instrukcja

13 Października 2024
Acer

Acer S242HL Instrukcja

12 Października 2024