Instrukcja obsługi Panamax SEP-200

Panamax nieskategoryzowany SEP-200

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Panamax SEP-200 (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

1690 Corporate Circle, Petaluma, CA 94954 800-472-5555 www.panamax.com• •

DESCRIPTION

AC surge protector permanently connected to main service panel.

SEP-200 SERVICE ENTRANCE PROTECTOR features a compact

chassis for easy installation, visible diagnostic LED,

120/240 V, 1 Phase, 3 wire plus ground.

For use with panels rated up to 400 Amps.

APPLICATION

SEP-200 protects against electrical surges

that can cause damage to electric and

electronic equipment. Catastrophic

failures and gradual component

degradation can be caused by

high voltage surges, which are

generated by harsh weather

conditions, external power

problems, or day-to-day

electrical component switching.

The SEP-200 will protect electrical

equipment against surges caused by

the above factors. Panamax also

recommends using secondary plug-in

protectors at the equipment you would like to protect.

SAFETY CONSIDERATIONS

A licensed electrician must install the SEP-200. Installation must follow applicable electrical codes. Failure

to follow installation instructions may result in personal injury, equipment damage and invalidation of

the warranty. Your electrical system must be grounded per Article 250 of the NEC. Surge protection

works best when a secure ground is established. Check grounding before restoring power.

PRODUCT WARRANTY

Panamax warrants to the original owner of the Panamax SEP-200

surge protector, for five (5) years following the date of purchase of the

protector, that the surge protector shall be free of defects in design,

material or workmanship. Panamax will repair or replace any such

defective unit during the warranty period.

CONNECTED MAJOR APPLIANCE PROTECTION POLICY

Panamax will pay to repair or replace covered major household

appliances, up to an aggregate three year total of $10,000, if the major

household appliance, as defined herein, is damaged by an AC power or

lightning surge. The Panamax surge protector must show signs of

damage or be operating outside of design specifications.

Original owner is defined as: either the original purchaser of the

SEP-200 protector or the first homeowner to reside in the residential

household with the SEP-200 protector. Major household appliances

are defined as the following motor driven household loads:

refrigerator, freezer, oven, range, washer, dryer, ceiling fan, or

dishwasher.

THIS WARRANTY IS SUBJECT TO THE CONDITIONS BELOW

1. COVERED RISK: This warranty covers the above described major

household appliances from any and all damage resulting from either

an AC power surge or line overvoltage for the warranty period defined

herein. This coverage is secondary to any existing manufacturer’s

warranty, implied or expressed; or any service contract in existence at

the time of the loss, or to any applicable insurance policy in effect.

2. WARRANTY PERIOD: The SEP-200 Warranty shall be in effect for

three (3) years following the date of purchase of the protector.

Panamax reserves the right to require proof of proper installation in

the event of a claim.

3. PROPER INSTALLATION: The SEP-200 surge protector must be

properly installed by a certified electrician. Building wiring, grounding

and other electrical connections must conform to current applicable

codes (NEC or CEC). Panamax installation instructions and diagrams

must be followed.

4. DETERMINATION OF FAILURE: The Panamax SEP-200 protector

must show signs of damage or must be performing outside of design

specifications. OPENING THE ENCLOSURE, TAMPERING WITH, OR

MODIFYING THE PROTECTOR IN ANY WAY SHALL VOID YOUR

WARRANTY.

5. EXCLUSIONS: The SEP-200 WARRANTY DOES NOT COVER: service

charges; installation costs; reinstallation costs; setup cost; diagnostic

charges; periodic checkups; routine maintenance; loss of use of the

product; costs or expenses arising out of reprogramming or loss of

programming; shipping charges or fees; service calls; loss or damage

occasioned by fire, theft, flood, wind, accident, abuse or misuse.

6. MAKING A CLAIM:

a) Contact the Panamax Customer Relations department by internet at

www.panamax.com or call toll-free at 1-800-472-5555 to obtain a

Return Authorization (RA) number. IF YOU BELIEVE YOU HAVE

DAMAGE TO A MAJOR HOUSEHOLD APPLIANCE AS DEFINED, YOU

MUST NOTIFY PANAMAX AT THIS TIME.

b) Panamax will send you a one page claim statement to be completed

and returned. You must include either the original proof of purchase of

the be followed.protector or the work order for the installation of the

SEP-200 protector with your completed claim statement.

c) Once you obtain an RA number, please clearly mark your RA number

on the side of your protector. Place your protector in a box and add

packing materials. On the outside of the box, please clearly mark the RA

number.

d) Ship the protector to Panamax. You are responsible for charges for

shipping the protector to Panamax.

e) Once Panamax has received your claim statement and has confirmed

your eligibility, Panamax, at its sole option, will either pay the deductible

amount of the original owner's insurance policy covering major

household appliances or pay to repair or replace said major household

appliances.

f) Panamax reserves the right to inspect the damaged appliance(s),

parts, or circuit board, as well as the customer’s facility (at Panamax’s

expense). Damaged appliances deemed uneconomical to repair must

remain available for inspection by Panamax until the claim is finalized.

8. GENERAL: If you have any questions regarding this warranty, please

contact the Panamax Customer Relations Department at

www.panamax.com or toll-free at 1-800-472-5555. This warranty

supersedes all previous warranties. This is the only warranty provided

with the protector and any other implied or expressed warranties are

non-existent. This warranty may not be modified except in writing,

signed by an officer of the Panamax corporation.

EFFECTIVE JAN. 2009 IWS00856 REV. A

SEP-200 Surge Protector Five Year Product Warranty and

Connected Appliance Protection Policy

(Valid only in the United States and Canada)

INDOOR / OUTDOOR INSTALLATION & OPERATING INSTRUCTIONS

FOR SERVICE ENTRANCE PROTECTOR

SEP-200

INSOO856 REV. B

SEP-200

SURGE PROTECTIVE DEVICE

PROTECTION OK

U.G.

SVC. TERM

SERVICE

CONDUIT

Backup Location 2

Backup Location 1

Preferred Location

SERVICE

PANEL

SEP-200

SURGE

PROTECTOR

WALL

CONDUIT ELBOW

SERVICE PANEL

SEP-200

CONDUIT

Figure 2

Figure 1

Back Mounting

Figure 3

Figure 4

SEP-200

TOP VIEW

WALL BOARD

SEP-200

For back mounting, use

pull-through elbow conduit(s)

and additional conduit sections

as needed. (Figures 3 & 4).

MOUNTING INSTRUCTIONS

Install the SEP-200 according to local electrical codes,

or using instructions below. Lead lengths must be as

short as possible to keep voltage drop to a minimum.

Trim excessive length to minimize wire impedance to

the surge protector. In the event of lightning or other

power transients, a one foot reduction of lead length can

result in a decrease of 100 volts or more across leads.

CAUTION: When installing or removing this protector

from service, disconnect power. Failure to do so may

result in equipment damage, serious injury or death.

Use a threaded nipple or thin-wall conduit to connect the

SEP-200 to the service panel. Feed the wires through

the conduit and into the panel.

Using the screw holes on the back plate corners, mount

SEP-200 as close as possible to the service panel

(Figure 2).

TYPE1 (INSTALLATION THE MAIN DISCONNECT - Figure 5)BEFORE

WARNING:

REMOVE THE METER OR OTHERWISE DISCONNECT THE AC

POWER BEFORE BEGINNING THE INSTALLATION!!!

USE A TEST LAMP TO CONFIRM THAT THE POWER HAS BEEN REMOVED!!

The SEP-200 is UL Listed for installation either before or behind the main

service disconnect. Proper installation before the service disconnect usually

provides better protection (lower limiting voltage)than installations behind

the service disconnect. The mechanical installation to the meter pan or meter

side of the service panel is as described in figures 1-3, as close as possible

to the wiring between the meter and the service disconnect.

CONNECTIONS:

1. The 4 SEP-200 wires should be connected to the points"B" in figure 5.

The connections can be made at the meter socket or on the wiring to the

main disconnect.

2. Connect the SEP-200 green (ground) wire to the service raceway, the

panel ground bus, or any other part of the grounding electrode system.

The ground wire should be kept as short aspossible.

3. Connect the white (neutral) wire to the neutral bus.

4. Connect the two SEP-200 black wires to the two phase terminals of the

meter socket or to the conductors to the disconnect. An insulated tap

connector such as ILSCO KUPLER IPC 4/0-#6 is a fast and easy way to

connect the black (phase) wires to the service conductors.

5. Check the connections!

6. Replace the meter, or turn the AC power switch back on. The green light

on the SEP-200 should come on, confirming that the connections are correct

and there is power to both phases.

TYPE 2 (INSTALLATION THE MAIN DISCONNECT - Figure 6)AFTER

1. The should be installed by a qualified electrician.SEP-200

2. Turn "OFF" and lock out the power to the enclosure in which the SEP-200 is

to be installed.

3. Connect the green (ground)wire to the ground bus or connector.

4. Connect the white (neutral) wire to the neutral bus.

Install the appropriate 2 pole, 30 ampere (or larger) circuit breaker or lug kit

to the panel board or meter combination device. If a sub-feed lug kit is available,

it is a better and more economical connection than a breaker.

6. Connect the black leads to the load terminals of the circuit breaker or lug kit

and tighten to the required torque.

7. Double check connections, then reconnect power.

8. When the LED is on, the protector is functioning as desired.

MAIN

DISCONNECT

FROM SEP-200

HOT

GROUND

BUS

30A BREAKER

OR SUB-FEED NEUTRAL BUS

Figure 6

NEUTRAL BUS NEUTRAL

SEP-200

Figure 5

WIRING SCHEMATIC

120V

240V

WHITE

GREEN

WHITE

BLACK

BUILDING

GROUND

HOT

NEUTRAL

HOT

METER

GROUND

30A BREAKER

or SUB-FEED

LUG SET

GROUND

Specyfikacje produktu

Marka:	Panamax
Kategoria:	nieskategoryzowany
Model:	SEP-200
Kolor produktu:	Szary
Częstotliwość wejściowa AC:	50 - 60 Hz
Wysokość produktu:	63.5 mm
Szerokość produktu:	140 mm
Głębokość produktu:	140 mm
Waga produktu:	567 g
Zakres temperatur (eksploatacja):	-40 - 176 °C
Diody LED:	Tak
Maksymalne natężenie prądu:	20000 A
Głębokość:	5.5 "
Wysokość (imperialna):	2.5 "
Szerokość (imperialna):	5.5 "
Wartość znamionowa udaru energii:	2700 J
Ilość gniazd sieciowych:	- x gniazdo sieciowe
Wartość nominalna napięcia wejściowego:	100-240 V
Maksymalne napięcie elektryczne:	60000 V