Instrukcja obsługi Ozito PXCPPS-018U

Ozito nieskategoryzowany PXCPPS-018U

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ozito PXCPPS-018U (3 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
1016
CORDLESS
POLE PRUNER
SAFETY WARNINGS
Page 2
SPECIAL SAFETY INSTRUCT
Information about the battery
1. The battery pack supplied with your cordless tool is not charged. The battery
pack has to be charged before you use the tool for the  rst time.
2. For optimum battery performance avoid low discharge cycles. Charge the
battery pack frequently.
3. Store the battery pack in a cool place, ideally at 15°C and charged to at least
40%.
4. Lithium-ion batteries are subject to a natural ageing process. The battery
pack must be replaced at the latest when its capacity falls to just 80% of its
capacity when new. Weakened cells in an aged battery pack are no longer
capable of meeting the high power requirements and therefore pose a safety
risk.
5. Do not throw battery packs into an open  re. There is a risk of explosion!
6. Do not ignite the battery pack or expose it to re.
7. Donotexhaustivelydischargebatteries. Exhaustive discharge will
damage the battery cells. The most common cause of exhaustive discharge
is lengthy storage or non-use of partly discharged batteries. Stop working
as soon as the performance of the battery falls noticeably or the electronic
protection system triggers. Place the battery pack in storage only after it has
been fully charged.
8. Protectbatteriesandthetoolfromoverloads. Overloads will quickly
result in overheating and cell damage inside the battery housing without this
overheating actually being apparent externally.
9. Avoiddamageandshocks. Replace batteries which have been dropped
from a height of more than one meter or which have been exposed to violent
shocks without delay, even if the housing of the battery pack appears to be
undamaged. The battery cells inside the battery may have suff ered serious
damage. In this respect, please also read the waste disposal information.
10. If the battery pack suff ers overloading and overheating, the integrated
protective cut-off will switch off the equipment for safety reasons. Important.
Do not press the ON/OFF switch any more if the protective cut-off has
actuated. This may damage the battery pack.
11. Use only original battery packs. The use of other batteries may result in
injuries, explosion and a re risk.
Information on chargers and the charging process
1. Please check the data marked on the rating plate of the battery charger.
Be sure to connect the battery charger to a power supply with the voltage
marked on the rating plate. Never connect it to a diff erent mains voltage.
2. Protect the battery charger and its cable from damage and sharp edges.
Have damaged cables repaired without delay by a quali ed electrician.
3. Keep the battery charger, batteries and the cordless tool out of children’s
reach.
4. Do not use damaged battery chargers.
5. Do not use the supplied battery charger to charge other cordless tools.
6. In heavy use the battery pack will become warm. Allow the battery pack to
cool to room temperature before commencing with the charging.
7. Donotover-chargebatteries. Do not exceed the maximum charging times.
These charging times only apply to discharged batteries. Frequent insertion
of a charged or partly charged battery pack will result in over-charging and
cell damage. Do not leave batteries in the charger for days on end.
8. Neveruseorchargebatteriesifyoususpectthatthelasttimetheywere
chargedwasmorethan12monthspreviously.There is a high probability
that the battery pack has already suffered dangerous damage (exhaustive
discharge).
9. Charging batteries at a temperature below 10°C will cause chemical damage
to the cell and may cause a re.
10. Do not use batteries which have heated during the charging process, as the
battery cells may have suff ered dangerous damage.
11. Do not use batteries which have suff ered curvature or deformation during
the charging process or which show other non-typical symptoms (gassing,
hissing, cracking,…)
12. Never fully discharge the battery pack (recommended depth of discharge max.
80%) A complete discharge of the battery pack will lead to premature ageing
of the battery cells.
13. Never charge the batteries unsupervised.
Protection from environmental influences
1. Wear suitable work clothes. Wear safety goggles.
2. Protectyourcordlesstoolandthebatterychargerfrommoistureand
rain. Moisture and rain can cause dangerous cell damage.
3. Do not use the cordless tool or the battery charger near vapors and
inammable liquids.
4. Use the battery charger and cordless tools only in dry conditions and an
ambient tempe- rature of 10-40°C.
5. Do not keep the battery charger in places where the temperature is liable to
reach over 40°C. In particular, do not leave the battery charger in a car that is
parked in the sunshine.
6. Protectbatteriesfromoverheating.Over- loads, over-charging and
exposure to direct sunlight will result in overheating and cell damage. Never
charge or work with batteries which have been overheated – replace them
immediately if possible.
7. Storageofbatteries,batterychargersandcordlesstools. Store the
charger and your cordless tool only in dry places with an ambient temperature
of 10-40°C. Store your lithium-ion battery pack in a cool, dry place at a
temperature of 10-20°C. Protect them from humidity and direct sunlight. Only
place fully charged batteries in storage (charged at least 40%).
8. Prevent the lithium-ion battery pack from free- zing. Battery packs which were
stored below 0°C for more than 60 minutes must be dispo- sed of.
9. When handling batteries beware of electro- static charge: Electrostatic
discharges cause damage of the electronic protection system and the battery
cells. Avoid electrostatic char- ging and never touch the battery poles.
Rechargeable batteries and cordless electricmachines and tools contain materials
that are potentiallyharmful to the environment. Never placeany cordless electric
machines or tools in your household refuse. When cordless electric machines or
tools become defective or worn, remove the rechargeable batteries and return
them to iSC GmbH (address: Eschenstrasse 6, D-94405, Germany). If the
rechargeable batteries cannot be removed, return the complete cordless machine
or tool.
You can then be sure that the equipment will be correctly disposed of by the
manufacturer.
Whenshippingordisposingofbatteriesandcordlesstools,alwaysensure
thattheyarepackedindividuallyinplasticbagstopreventshortcircuits
andres.
Residualrisks
Even when the tool is used as prescribed it is not possible to eliminate all
residual risk factors. The following hazards may arise in connection with the tool’s
construction and design:
1. Damage to lungs if an effective dust mask is not worn.
2. Damage to hearing if effective hearing protection is not worn.
3. Health defects resulting from vibration emission if the appliance is being
used over longer period of time or not adequately managed and properly
maintained.
WARNING! This machine produces an electromagnetic eld during operation.
This eld may under some circumstances interfere with active or passive
medical implants. To reduce the risk of serious or fatal injury, we recommend
persons with medical implants to consult their physician and the medical
implant manufacturer before operating this machine.
Donotlosethesesafetyinstructions.
BATTERY AND CHARGER SAFETY WARNINGS
Readallsafetyregulationsandinstructions.
Any errors made in following the safety regulations and instructions may result in an electric shock,  re and/or serious injury.
Keepallsafetyregulationsandinstructionsinasafeplaceforfutureuse.
The term “electric tool” used in the safety instructions refers to electric tools operated from the mains power supply (with a power cable) and to battery operated electric
tools (without a power cable).
DANGER!
GENERAL SAFETY INSTRUCTIONS FOR ELECTRIC TOOLS
1.Workplacesafety
a) Keep your work area clean and well illuminated. Untidy or unlit work areas can
result in accidents.
b) Do not operate the electric tool in an environment where there is a risk of
explosions and where there are in ammable liquids, gases or dust. Electric
tools produce sparks which could set the dust or vapours alight.
c) Keep the electric tool out of the reach of children and other persons. If there is
a distraction, you may lose control of the appliance.
2.Electricalsafety
a) The connector plug from this electric tool must  t into the socket. The plug
should never be altered in any way. Never use adapter plugs together with
earthed electric tools. Unaltered plugs and correct sockets reduce the risk of an
electric shock.
b) Avoid bodily contact with earthed surfaces such as pipes, heating, ovens and
fridges. The risk of electric shock is increased if your body is earthed.
c) Keep the tool out of the rain and away from moisture. The ingress of water into
an electric tool increases the risk of an electric shock.
d) Do not use the cable to carry the electric tool, to hang it up or to pull it out of
the socket. Keep the cable away from heat, oil, sharp edges and moving parts
of the appliance. Damaged or entangled cables increase the risk of an electric
shock.
e) If you are working outdoors with an electric tool, only use extension cables
which are designed speci cally for this purpose. Using specially designed
outdoor extension cables, the risk of electric shock is reduced.
f) If operation of the electric tool in a damp environment can not be avoided, use a
earth-leakage circuit-breaker. The earthleakage circuit-breaker reduces the risk
of an electric shock.
3.Safetyofpersons
a) Be careful, watch what you are doing and use an electric tool sensibly. Do
not use the tool if you are tired or under the in uence of drugs, alcohol or
medication. A moment of inattention when using the electric tool can result in
serious injuries.
b) Wear personal protection equipment and always wear safety goggles.
Wearing personal protection (such as dust masks, non-slip safety shoes,
safety helmet or ear protection, depending upon the type and use of the
electric tool) reduces the risk of injury.
c) Make sure that the appliance cannot start up accidentally. Ensure that the
electric tool is switched off before you connect it to the power supply and/or
insert the battery, or pick up or carry the tool. If your  nger is on the switch
whilst carrying the electric tool or if you connect the appliance to the mains
when it is switched on, this can lead to accidents.
d) Remove keys and wrenches before switching on the electric tool. A tool or
key which comes into contact with rotating parts of the appliance can lead to
injuries.
e) Avoid abnormal working postures. Make sure you stand squarely and keep
your balance at all times. In this way, you can control the electric tool better in
unexpected circumstances.
f) Wear suitable work clothes. Do not wear loose clothing or jewellery. Keep
hair, clothes and gloves away from moving parts. Loose clothing, jewellery or
long hair can get trapped in moving parts.
g) If vacuuming devices and draining devices can be  tted, make sure that
these are correctly attached and correctly used. The use of a dust extraction
system can reduce the danger posed by dust
4.Usageandtreatmentofelectricaltool
a) Do not overload the appliance. Use the correct tool for your work. You will be
able to work better and more safely within the given performance boundaries.
b) Do not use an electric tool with a defective switch. An electric tool that cannot
be switched on or off is dangerous and must be repaired.
c) Pull the plug out of the socket and/or remove the battery before making any
adjustments to the appliance, changing accessories or put the appliance
down. This safety measure prevents starting the electric tool unintentionally.
d) Keep unused electric tools out of the reach of children. Do not allow
people who are not familiar with the appliance or who have not read these
instructions to use the appliance. Electric tools are dangerous if they are used
by inexperienced people.
e) Clean your electric tool carefully. Check whether moving parts are functioning
properly and not jamming, whether parts are broken or damaged enough that
the functioning of this electric tool is aff ected. Have damaged parts repaired
before using the appliance. Many accidents are caused by badly maintained
electric tools.
f) Keep your cutting tools sharp and clean. Carefully maintained cutting tools
with sharp cutting edges will jam less and are easier to control.
g) Make sure to use electric tools, accessories, attachments, etc. in accordance
with these instructions. Take the conditions in your work area and the job in
hand into account. Using electric tools for any purpose other than the one for
which they are intended can lead to dangerous situations.
5)Batterytooluseandcare
a) Rechargeonlywiththechargerspeciedbythemanufacturer. A charger
that is suitable for one type of battery pack may create a risk of re when used
with another battery pack.
b) Usepowertoolsonlywithspecicallydesignatedbatterypacks. Use of
any other battery packs may create a risk of injury and re.
c) Whenbatterypackisnotinuse,keepitawayfromothermetalobjects,
likepaperclips,coins,keys,nails,screwsorothersmallmetalobjects,
thatcanmakeaconnectionfromoneterminaltoanother. Shorting the
battery terminals together may cause burns or a re.
d) Underabusiveconditions,liquidmaybeejectedfromthebattery;avoid
contact.Ifcontactaccidentallyoccurs,ushwithwater.Ifliquidcontacts
eyes,additionallyseekmedicalhelp. Liquid ejected from the battery may
cause irritation or burns.
6.Service
a) Have your electric tool repaired only by trained personnel using only genuine
spare parts. This will ensure that your electric tool remains safe to use.
Page 4

Specyfikacje produktu

Marka: Ozito
Kategoria: nieskategoryzowany
Model: PXCPPS-018U

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ozito PXCPPS-018U, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje nieskategoryzowany Ozito

Ozito

Ozito PXMBC-004 Instrukcja

29 Maja 2024
Ozito

Ozito PXCPPS-018U Instrukcja

28 Maja 2024
Ozito

Ozito OAST-050 Instrukcja

26 Maja 2024
Ozito

Ozito PXHTK-400 Instrukcja

24 Maja 2024
Ozito

Ozito PXWBS-200U Instrukcja

21 Maja 2024
Ozito

Ozito ATAK-009 Instrukcja

21 Maja 2024
Ozito

Ozito UJC-860 Instrukcja

20 Maja 2024
Ozito

Ozito PXBCSS-184 Instrukcja

20 Maja 2024
Ozito

Ozito PXCBLK-218 Instrukcja

19 Maja 2024
Ozito

Ozito PXSMSK-800MS Instrukcja

13 Maja 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024
Asko

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024
Emko

Emko EZM-9920 Instrukcja

27 Października 2024
Emko

Emko ESM-3712-H Instrukcja

27 Października 2024
Emko

Emko ATS-10 Instrukcja

27 Października 2024
Emko

Emko EAOM-11.2 Instrukcja

27 Października 2024
Emko

Emko EPM-3790 Instrukcja

27 Października 2024
Emko

Emko EPM-7790 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux IAN 108340 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024