Instrukcja obsługi Ozito PXCCSK-418

Ozito Maszyna do piłowania PXCCSK-418

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ozito PXCCSK-418 (12 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
SPECIFICATIONS
Input: 18V
Bar Length: 250mm (10”)
Cutting Length Max.: 230mm
Chain Speed: 4.3m/s
Chain Pitch: 9.53mm (3/8”)
Chain Gauge: 1.1mm (.043”)
Oil Tank Capacity: 200ml
Weight: 3.0kg
STANDARD EQUIPMENT
Chainsaw
CORDLESS
CHAINSAW
INSTRUCTION MANUAL
ozito.com.au
Guide Bar Cover
Screwdriver
PXCCSS-018
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
OZITO Australia/New Zealand (Head Ofce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
0718
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other
than that specied on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty Warranty excludes consumable parts, for example: guide bar, chain
and included accessories.
10
in
250
mm
3/8” LP
40
10
in
250
mm
3/8” LP
40
10
in
250
mm
3/8” LP
40
KNOW YOUR PRODUCT SETUP & PREPARATION
1. INSERTING & REMOVING BATTERY
1. Rear Handle
2. Trigger Switch
3. Oil Level Window
4. Chain Oil Tank Cap
5. Side Cover
6. Front Handle
7. Chain Brake
8. Guide Bar Locking Knob
9. Guide Bar
10. Chain
11. Bucking Spikes
12. Motor Cover
13. Lock-Off Button
14. Battery Seating
CORDLESS CHAINSAW
1 2 3 4 5 6 7 8
BATTERY & CHARGER
This tool is compatible with all battery and chargers from the Ozito
Power X Change Range.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to the
online manual.
ACCESSORIES
15 Guide Bar Cover 16 Screwdriver
15 16
10
11 12 13 14
9
10
in
250
mm
Installing a Battery into the Chainsaw
1. Align the ribs of the battery with
the recess below the handle
Removing a Battery from the Chainsaw
2. Slide the battery in so
that it clicks into place.
1. Press and hold the battery
release tab to release the
battery.
2. Slide the battery out.
2. OIL 3. SWITCHING ON/OFF
OPERATION
Running in the Chain
Prior to operation, a new chain should be run in for 2–3 minutes and then its
tension should be checked and adjusted as detailed in “MAINTENANCE”.
Note: Chain bar oil may leak if the tool is left for long periods. This is
normal. If the tool is to be left unused for an extended time, drain the oil from
the tool. Rell before use.
Switching ON
1. Pull the hand guard/chain brake
towards you.
2. Hold the front handle with your
left hand and the rear handle
with your right hand.
Switching OFF
1. Release the trigger switch, the
chain and motor will quickly stop.
10
in
250
mm
3/8” LP
40
10
in
250
mm
3/8” LP
40
3. Press the lock-off button with
your thumb, then squeeze the
trigger switch. The chainsaw
starts after a short delay.
4. The chain will now be running,
ready to make a cut. Release
the lock-off switch.
5. To check the lubricating system,
switch on the chainsaw and hold it
with the guide bar and chain above
some light coloured paper such as
newspaper. A steadily increasing
stain caused by oil spray shows
the lubricating system is working.
2. Fill the tank with chain bar oil.
The capacity of the chain oil
tank is 220ml. Do not over ll.
4. Always ll the oil tank when the
oil level is below the minimum
mark on the oil level window.
WARNING!: NEVER START WORK UNLESS THE
CHAIN AND BAR ARE LUBRICATED
1. Remove the chain bar oil cap.
3. Ret cap and clean any oil
spillage.
IMPORTANT: ONLY USE OIL THAT IS EXPRESSLY LABELLED
“CHAIN BAR OIL”.
10
in
250
mm
3/8” LP
40

Specyfikacje produktu

Marka: Ozito
Kategoria: Maszyna do piłowania
Model: PXCCSK-418

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ozito PXCCSK-418, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Maszyna do piłowania Ozito

Ozito

Ozito PXBCS-1830 Instrukcja

24 Grudnia 2024
Ozito

Ozito PXCCSK-4182 Instrukcja

8 Października 2024
Ozito

Ozito PXBPCK-1825 Instrukcja

8 Października 2024
Ozito

Ozito PXTCSK-2520 Instrukcja

8 Października 2024
Ozito

Ozito PXPRSS-018 Instrukcja

7 Października 2024
Ozito

Ozito PXBPCS-1815 Instrukcja

7 Października 2024
Ozito

Ozito JSW-6100U Instrukcja

22 Września 2024
Ozito

Ozito OCS-018 Instrukcja

20 Września 2024
Ozito

Ozito RSW-5200 Instrukcja

18 Września 2024
Ozito

Ozito JSW-4000U Instrukcja

18 Września 2024

Instrukcje Maszyna do piłowania

Najnowsze instrukcje dla Maszyna do piłowania

Alpina

Alpina APR 26 Instrukcja

22 Marca 2025
Gamma

Gamma HCZ2-85 Instrukcja

11 Marca 2025
Baumr-AG

Baumr-AG SW1 Instrukcja

10 Marca 2025
Stiga

Stiga PR 100e Instrukcja

9 Marca 2025
Bosch

Bosch EasyChain 18V-15-7 Instrukcja

27 Lutego 2025
Worx

Worx Nitro WX501 Instrukcja

26 Lutego 2025
DeWalt

DeWalt DCS383 Instrukcja

12 Lutego 2025
EGO

EGO PSX2510 Instrukcja

6 Lutego 2025
Hilti

Hilti WSR 1400-PE Instrukcja

4 Lutego 2025
Husqvarna

Husqvarna 455e Rancher Instrukcja

12 Stycznia 2025