Instrukcja obsługi Ozito PXBCS-1830

Ozito Maszyna do piłowania PXBCS-1830

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ozito PXBCS-1830 (8 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
PXBCS-1830
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other
than that specied on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty Warranty excludes consumable parts, for example: guide bar, chain
and included accessories.
OZITO. 25 Fox Drive, Dandenong South, Victoria 3175, Australia
MIN
300
MM
(12”)
MIN
300
MM
(12”)
STANDARD EQUIPMENT
Chainsaw
CHAINSAW
INSTRUCTION MANUAL
ozito.com.au
Guide Bar Cover
Guide Bar & Chain
SPECIFICATIONS
Input: 18V
Bar Length: 300mm (12”)
Cutting Length: 270mm max.
Chain Speed: 6.0 / 8.9 m/s
Chain Pitch: 9.53mm (3/8”)
Chain Gauge: 1.1mm (0.043”)
Oil Tank: 160ml max.
Sound Power Level: 100 dB
Weight: 4.03kg
0824
This product is intended for use by a competent
trained person. This user manual is a guide only and
should not be treated as a training manual.
• Please seek professional training before use.
• This product is designed for felling small trees, limbing of branches,
sawing wooden beams and pruning of trees, shrubs and bushes while
user is rmly footed on the ground.
1. ASSEMBLY
MIN
300
MM
(12”)
MIN
MIN
300
MM
(12”)
300
MM
(12”)
30
AB
4. Place the guide bar
and chain in position,
ensuring that the chain
is around sprocket
(A). Also ensure that
the threaded pin (B)
ts into the guide bar
tension dial.
If it does not t, it can
be adjusted slightly by
turning the dial.
5. Attach the side cover and secure it with
the guide bar lock knob. Do not fully
tighten the guide bar lock knob until after
adjusting the chain tension.
1. Completely unscrew the guide bar
lock knob, rotating in a counter
clockwise direction.
Fitting the Chain & Bar
2. Remove the side cover.
3. Fit the chain over the guide bar,
making sure that the cutters are
facing in the direction of rotation.
IMPORTANT: IF THE CHAIN IS INSTALLED BACKWARDS
(CHAIN CUTTERS ARE FACING IN THE OPPOSITE DIRECTION
OF ROTATION) THE CHAINSAW WILL VIBRATE EXCESSIVELY
AND NOT CUT.
WARNING!: ENSURE THE CHAINSAW IS SWITCHED
OFF AND THE BATTERY IS DISCONNECTED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
WARNING!: ALWAYS WEAR GLOVES WHEN HANDLING
THE CHAIN. THE CHAIN CUTTERS ARE SHARP AND
COULD CUT YOU.
KNOW YOUR PRODUCT SETUP & PREPARATION
1. Rear Handle
2. On/Off Trigger
3. Oil Level Window
4. Side Cover
5. Guide Bar Lock Knob
6. Hand Guard/Chain Brake
7. Chain Tension Dial
8. Guide Bar
9. Chain
10. Bucking Spikes
11. Front Handle/Carry Handle
12. Speed Control
13. Oil Tank Cap
14. Motor Cover
15. Battery Seating
16. Lock-Off Button
17. Guide Bar Cover
BRUSHLESS CHAINSAW
BATTERY & CHARGER
This tool is compatible with all battery and chargers
from the Ozito PXC Range.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to the
online manual.
1 3 4 6 7 8
1410 11
9
1512 13
2 5
16
17
For convenience and ease of assembly, the chain is pre-tted over the
guide bar with the cutters facing in the direction of rotation. Refer to the
supplied A5 insert for further information before tting the bar & chain
for the rst time.
2. OIL
300
MM
(12”)
3 - 4mm gap is
the ideal tension
300
MM
(12”)
MIN
300
MM
(12”)
Note: Proper tension of the
chain is extremely important
and must be checked before
starting, as well as during any
cutting operation. Taking the
time to make adjustments to the chain will result in improved cutting
performance and prolonged chain life.
WARNING!: DO NOT OPERATE THIS CHAINSAW WITH
LONG LOOSE HAIR OR LOOSE FITTING JEWELLERY. TIE
LONG LOOSE HAIR BACK AND REMOVE LOOSE FITTING
JEWELLERY.
IMPORTANT: IF YOU TRY TO ROTATE THE CHAIN TENSIONING
DIAL WHILST THE GUIDE BAR LOCK KNOB IS TIGHT, IT WILL
RESULT IN THE CHAIN NOT LOOSENING AND POSSIBLE
DAMAGE TO THE MECHANISM.
Adjusting the Chain Tension
1. Loosen the guide bar lock knob,
rotating in a counter clockwise
direction.
2. Adjust the chain tension
with the chain tensioning
dial. Turning the dial
CLOCKWISE increases
the chain tension, turning
it COUNTER-CLOCKWISE
decreases the chain
tension.
For the correct chain tension, rmly
pull up on the chain at the middle
of the top of the exposed guide bar.
When the chain is pulled up to its
highest point, the bottom tip of the
links should only just stay in the
track [middle of the guide bar].
3. After the chain has been
accurately tensioned, lock
the guide bar in place with
the guide bar lock knob.
Note: Chain bar oil may leak if the chainsaw is left for long periods.
This is normal. If the chainsaw is to be left unused for an extended
time, drain the oil from the oil tank. Rell before use.
5. To check the lubricating
system, switch on the
chainsaw and hold it with
the guide bar and chain
above some light coloured
paper such as newspaper.
A steadily increasing stain
caused by oil spray shows
the lubricating system is
working.
2. Fill the tank with chain bar oil. The
capacity of the chain oil tank is
160ml. Do not over ll.
4. Always ll the oil tank when the
oil level is below the minimum
mark on the oil level window.
Note: Always clean up any oil
spillage from product or area with an
absorbent towel before use. Always
discard waste according to your Local
government policies and laws.
WARNING!: NEVER START WORK UNLESS THE
CHAIN AND BAR ARE LUBRICATED. USE OF THE
CHAINSAW WITHOUT SAW CHAIN OIL OR IF THE OIL
LEVEL IS BELOW THE ‘MIN’ MARK WILL DAMAGE THE
CHAINSAW.
1. Place the chainsaw on a level
surface, then unscrew the chain
bar oil cap.
3. Ret cap and clean any oil spillage before placing the chainsaw back
in the upright position.
IMPORTANT: ONLY USE OIL THAT IS EXPRESSLY LABELLED
‘CHAIN BAR OIL’.
Running in the Chain
Prior to operation, a new chain should be run in for 2–3 minutes
and then its tension should be checked and adjusted as detailed in
‘ASSEMBLY - Adjusting the Chain Tension’.
WARNING!: WHEN TRANSPORTING THE CHAINSAW
FROM ONE LOCATION TO ANOTHER, ALWAYS CARRY BY
THE FRONT HANDLE ONLY, NEVER CARRY HOLDING THE
BLADE AS IT IS SHARP AND WILL CUT YOU.
IMPORTANT: IT IS VITAL FOR THE PROPER AND SAFE
OPERATION OF THE CHAINSAW THAT THE CHAIN IS TENSIONED
CORRECTLY.

Specyfikacje produktu

Marka: Ozito
Kategoria: Maszyna do piłowania
Model: PXBCS-1830

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ozito PXBCS-1830, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Maszyna do piłowania Ozito

Ozito

Ozito PXBCS-1830 Instrukcja

24 Grudnia 2024
Ozito

Ozito PXCCSK-4182 Instrukcja

8 Października 2024
Ozito

Ozito PXBPCK-1825 Instrukcja

8 Października 2024
Ozito

Ozito PXTCSK-2520 Instrukcja

8 Października 2024
Ozito

Ozito PXPRSS-018 Instrukcja

7 Października 2024
Ozito

Ozito PXBPCS-1815 Instrukcja

7 Października 2024
Ozito

Ozito JSW-6100U Instrukcja

22 Września 2024
Ozito

Ozito OCS-018 Instrukcja

20 Września 2024
Ozito

Ozito RSW-5200 Instrukcja

18 Września 2024
Ozito

Ozito JSW-4000U Instrukcja

18 Września 2024

Instrukcje Maszyna do piłowania

Najnowsze instrukcje dla Maszyna do piłowania

Husqvarna

Husqvarna 455e Rancher Instrukcja

12 Stycznia 2025
Güde

Güde GSS 400 Instrukcja

12 Stycznia 2025
Makita

Makita DUC306PG2 Instrukcja

12 Stycznia 2025
HiKOKI

HiKOKI C 6BU3 Instrukcja

11 Stycznia 2025
DEDRA

DEDRA DED7060 Instrukcja

11 Stycznia 2025
Einhell

Einhell KGS 190 Instrukcja

11 Stycznia 2025
Sun Joe

Sun Joe SWJ599E Instrukcja

11 Stycznia 2025
Einhell

Einhell BT-MB 550 U Instrukcja

11 Stycznia 2025
Maruyama

Maruyama MCV51 Instrukcja

11 Stycznia 2025
Vonroc

Vonroc JS505DC Instrukcja

9 Stycznia 2025