Instrukcja obsługi Ozito OZCCS85WA

Ozito Maszyna do piłowania OZCCS85WA

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ozito OZCCS85WA (8 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

CHAINSAW

CHAIN

SHARPENER

85W

INSTRUCTION MANUAL

OZCCS85WA

WHAT’S IN THE BOX

IN ORDER TO MAKE A CLAIM UNDER THIS

WARRANTY YOU MUST RETURN THE PRODUCT

TO YOUR NEAREST BUNNINGS WAREHOUSE WITH

YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO

RETURNING YOUR PRODUCT FOR WARRANTY

PLEASE TELEPHONE OUR CUSTOMER SERVICE

HELPLINE:

Australia 1800 069 486

New Zealand 0508 069 486

3 YEAR REPLACEMENT WARRANTY

Your product is guaranteed for a period of 36 months from

the original date of purchase. If a product is defective it will

be replaced in accordance with the terms of this warranty.

Warranty excludes consumable parts, for example: wheel.

WARNING

The following actions will result in the warranty being void.

• If the tool has been operated on a supply voltage other

thanthatspeciedonthetool.

• If the tool shows signs of damage or defects caused

by or resulting from abuse, accidents or alterations.

• Failure to perform maintenance as set out within the

instruction manual.

• If the tool is disassembled or tampered with in any way.

• Professional, industrial or high frequency use.

WARRANTY

TO ENSURE A SPEEDY RESPONSE PLEASE

HAVE THE MODEL NUMBER AND DATE OF

PURCHASE AVAILABLE. A CUSTOMER SERVICE

REPRESENTATIVE WILL TAKE YOUR CALL

AND ANSWER ANY QUESTIONS YOU MAY

HAVE RELATING TO THE WARRANTY POLICY

OR PROCEDURE.

OZITO Australia/NewZealand(HeadOfce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.

Thebenetsprovidedunderthiswarrantyareinaddition

to other rights and remedies which are available to you at law.

Our goods come with guarantees that cannot be excluded

at law. You are entitled to a replacement or refund for a major

failure and for compensation for any other reasonably foreseeable

loss or damage. You are also entitled to have the goods repaired

or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure.

Generally you will be responsible for all costs associated with

a claim under this warranty, however, where you have suffered

any additional direct loss as a result of a defective product you

may be able to claim such expenses by contacting our customer

service helpline above.

ozito.com.au

1014

SPECIFICATIONS

Motor: 85W

Input: 230V-240V ~ 50Hz

No load speed: 4,800/min

Table/vice angles: 0 – 35° left & right

Sharpening Wheel: Ø108 x 3.2mm

Bore: Ø23mm

Suits chain pitch: 0.325” and 3/8”

Weight: 2.4kg

Chainsaw Chain Sharpener

Sharpening Wheel

(assembled)

Table & Lock Knob

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to

the online manual.

Assembling the table

1. Insert the bolt of the table through

the hole in the base.

2. Secure the table in place by xing

the locking knob to the bolt (by

screwing the knob clockwise).

Mounting the sharpener

For safe operation of the sharpener, the base of the tool must be tted to

a at, solid, secure surface such as a work bench.

The sharpener base is designed in two halves. The rear half is for tting

at to a stable surface and the front is designed to protrude over the edge

of the mounting surface.

The sharpener base should

be tted to the mounting

surface by sliding the

rear half back until the

two ‘steps’ on the base

align with the edge of the

mounting surface. Ensure

when mounting, that the

table locking knob is still

easily accessible for when

adjusting the table angles.

Two 6mm mounting holes allow for xing

the base to the mounting surface (bolts

not supplied). Ensure the mounting

surface is capable of supporting the

weight of the sharpener and chain to

be sharpened.

1. Lowering hand piece

2. Sharpening wheel cover

3. Direction of rotation indicator

4. Safety guard

5. Sharpening wheel

6. Depth of grind knob

7. Depth of grind locking knob

8. Depth of grind pin

9. Guide clamp lever

10. Chain (tooth) stop

11. Guide

12 Depth stop platform

13. Table locking knob

14 Bench mounting holes

15. Sharpener base

16. Chain stop adjusting

knob lock nut

17. Adjustable table

18. Chain stop adjusting knob

19. Table scale

CHAINSAW CHAIN SHARPENER

KNOW YOUR PRODUCT

1. ASSEMBLY

SETUP & PREPARATION

9 10 11

14 15

WARNING!: BEFORE ASSEMBLING, MOUNTING,

SETTING OR MAINTAINING YOUR SHARPENER,

MAKE SURE THAT THE MOTOR IS OFF AND THE TOOL

DISCONNECTED FROM THE POWER SUPPLY TO PREVENT

ACCIDENTAL STARTING.

4. If you do not know the angle of the chain

set, the table angle to 35°.

Take hold of the hand piece and bring it

down so that the wheel is slowly lowered

into the chain, along the cutting tooth.

Slowly move the table so the cutting face

of the tooth is parallel with the edge of the

wheel. The most common chain angles

are 30 35°. It may be necessary to slide –

the chain slightly to allow the wheel to

enter down the face of the tooth.

5. Once the correct angle as been achieved

tighten the table locking knob to lock the

table in the current position.

After the table is locked in the required

position, take hold of the hand piece and

lower the head assembly until the wheel

is aligned along the tooth of the chain.

Conrm the angle then slide the chain so

the face of the tooth is just touching the

face of the wheel.

6. Lock the guide by rotating

the clamping lever as far

as it will go in a clockwise

direction. Ensure the chain

is clamped rmly into the

sliding guide. Should the

chain still not be clamped,

pull the clamping lever

outwards (away from the

guide), turn the lever anti-

clockwise 1/4 of a turn.

Push the lever back in towards the guide.

Proceed to rotate the lever fully clockwise.

Check the chain is clamped. Should it

still not be clamped, repeat the process

above.

2. SETTING OF THE SHARPENER

Note. Prior to using the sharpener, several adjustments must be made in

order to sharpen the teeth of the chain effectively.

1. Adjusting the angle of cut.

2. Adjusting the chain (tooth) stop.

3. Adjusting the depth of cut.

Failure to perform these adjustments will result in poor sharpening and

possible damage to the chain being sharpened.

Before making adjustments, always ensure the sharpener has been

disconnected from the power supply.

Adjusting the angle of cut

1. Open the slide guide groove

by rotating the guide clamp

lever anti-clockwise.

2. Fit a chain over the guide groove

ensuring the inner side of the chain

sits inside the guide groove. Ensure

the chain hangs freely over the side

of the mounting surface. The chain

should be tted so the teeth face the

right hand side of the sharpener and

the chain can move freely in both

directions.

3. If you know the angle of the chain,

rotate the table to the same angle as

the chain. To rotate the table loosen

the table lock knob and rotate the

table until the scale indicator lines

up with the scale on the base of the

sharpener.

Specyfikacje produktu

Marka:	Ozito
Kategoria:	Maszyna do piłowania
Model:	OZCCS85WA

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ozito OZCCS85WA, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Maszyna do piłowania Ozito

Ozito PXBCS-1830 Instrukcja

24 Grudnia 2024

Ozito PXCCSK-4182 Instrukcja

8 Października 2024

Ozito PXBPCK-1825 Instrukcja

8 Października 2024

Ozito PXTCSK-2520 Instrukcja

8 Października 2024

Ozito PXPRSS-018 Instrukcja

7 Października 2024

Ozito PXBPCS-1815 Instrukcja

7 Października 2024

Ozito JSW-6100U Instrukcja

22 Września 2024

Ozito OCS-018 Instrukcja

20 Września 2024

Ozito RSW-5200 Instrukcja

18 Września 2024

Ozito JSW-4000U Instrukcja

18 Września 2024

Instrukcje Maszyna do piłowania

Najnowsze instrukcje dla Maszyna do piłowania

Alpina APR 26 Instrukcja

22 Marca 2025

Gamma HCZ2-85 Instrukcja

11 Marca 2025

Baumr-AG SW1 Instrukcja

10 Marca 2025

Stiga PR 100e Instrukcja

9 Marca 2025

Bosch EasyChain 18V-15-7 Instrukcja

27 Lutego 2025

Worx Nitro WX501 Instrukcja

26 Lutego 2025

DeWalt DCS383 Instrukcja

12 Lutego 2025

EGO PSX2510 Instrukcja

6 Lutego 2025

Hilti WSR 1400-PE Instrukcja

4 Lutego 2025

Husqvarna 455e Rancher Instrukcja

12 Stycznia 2025