Instrukcja obsługi Ozito EPP-750

Ozito Maszyna do piłowania EPP-750

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ozito EPP-750 (8 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from the
original date of purchase and is intended for DIY (Do It Yourself)
use only. If a product is defective it will be replaced in accordance
with the terms of this warranty. Warranty excludes consumable
parts, for example: guide bar, chain and included accessories.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
TELESCOPIC
POLE PRUNER
750W 200MM (8”)
INSTRUCTION MANUAL
SPECIFICATIONS
Power: 750W
Chain Speed: 11 meters/second
No Load Speed: 6,000/min
Max Cutting Width: 180mm
Guide Bar Length: 200mm (8”)
Oil Tank Capacity: 60ml
Telescopic Range: 1.85 – 2.80m
Weight: 3.82kg
EPP-750
WHAT’S IN THE BOX
WARRANTY
ozito.com.au
0817
Shoulder Strap
Telescopic Pole Pruner
Chain
Guide Bar
Guide Bar Cover
50
50
Additional Handle
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
1. CHAIN & BAR
CAUTION!: THE CHAIN HAS SHARP EDGES. FOR YOUR
OWN SAFETY, PLEASE USE WORK GLOVES.
KNOW YOUR PRODUCT SETUP & PREPARATION
TELESCOPIC
POLE PRUNER
1. Chain
2. Guide bar
3. Chain sprocket cover
4. Motor housing
5. Telescopic shaft lock
6. Main shaft
7. Additional handle
8. Shoulder strap attachment
9. Oil tank cap
10. Chain tension dial
11. Chain cover lock
12. Switch lock
13. On/off trigger switch
14. Cord retainer
15. Chain sprocket
16. Bucking spikes
17. Rear handle
Fitting the guide bar and chain
1. Loosen the chain
cover lock and
remove the chain
sprocket cover.
2. Place the chain in the
groove of the guide bar
as shown. Refer to the
image printed on the
guide bar that indicates
the direction that the
chain should face.
3. Place the guide bar and
chain onto the mount,
ensuring that the chain
sits around the chain
sprocket.
4. Re-mountandnger-
tighten the side cover
with the chain cover
lock.
NOTE: Only tighten the chain cover locking knob securely once the
chain tension has been adjusted (see: Tensioning the chain).
WARNING!: ENSURE THE TOOL IS
DISCONNECTED FROM THE POWER SUPPLY
BEFORE ASSEMBLY.
IMPORTANT!: IF THE CHAIN IS INSTALLED
BACKWARDS (CHAIN CUTTERS ARE FACING IN THE
OPPOSITE DIRECTION OF ROTATION) THE POLE
PRUNER WILL VIBRATE EXCESSIVELY AND NOT CUT.
50
50
1
2
3
4
5
6
7
8
9 10 11 12 13
14 15 16
17
50
50
WARNING! NEVER START WORK UNLESS THE
CHAIN AND BAR ARE LUBRICATED.
3. SAW CHAIN LUBRICATION2. TENSIONING THE CHAIN
1. Place the telescopic
pole pruner on a level
surface.
2. Clean the area around the oil
tank cap and then open it.
3. Fill the oil tank with BAR AND
CHAIN OIL (not supplied) to
maximumllline.Donotoverll
in doing so, make sure that no
dirt gets into the oil tank. This will
ensure that the oil nozzle does
not clog.
4. Close the oil tank cap.
WARNING!: THE USE OF THE POLE PRUNER
WITHOUT BAR AND CHAIN OIL OR WITH AN OIL
LEVEL BELOW THE MINIMUM OIL LEVEL MARK WILL
RESULT IN DAMAGE TO THE CHAIN!
1. Loosen the chain cover
lock. Do not remove the
side cover.
2. Adjust the chain tension with the
chain tensioning dial. Turning
the dial CLOCKWISE increases
the chain tension, turning it
COUNTER-CLOCKWISE
decreases the chain tension.
3. For the correct chain tension,
rmlypulluponthechainatthe
middle of the top of the exposed
guide bar. When the chain is
pulled up to its highest point, the
bottom tip of the links should only
just stay in the track [middle of the
guide bar]
4. After the chain has been
accurately tensioned, lock
the guide bar in place with
the chain cover lock.
5. Check the tension again
afterafewminutesofcuttingandseveraltimesinthersthour
because the chain will lengthen as it breaks in. Adjust as you go. A
loose chain causes rapid wear to both the chain and the guide bar
and could derail causing a major safety hazard.
NOTE: Proper tension of the chain is extremely important and must be
checked before starting, as well as during any cutting operation. Taking
the time to make adjustments to the chain will result in improved
cutting performance and prolonged chain life.
5. To check the lubricating system, switch on the pole pruner and hold
it with the guide bar and chain above some light coloured paper
such as newspaper. A steadily increasing stain caused by oil spray
shows the lubricating system is working.
NOTE: Guide bar oil may leak if the tool is left for long periods. This is
normal. If the tool is to be left unused for an extended time, drain the
oilfromthetool.Rellbeforeuse.
CAUTION!: IF YOU TRY TO ROTATE THE CHAIN
TENSIONING ADJUSTMENT DIAL WHILST THE CHAIN
COVER LOCK IS TIGHT, IT WILL RESULT IN THE CHAIN
NOT LOOSENING AND POSSIBLE DAMAGE TO THE
MECHANISM.
MAX.
50
CAUTION!: THE CHAIN HAS SHARP EDGES. FOR YOUR
OWN SAFETY, PLEASE USE WORK GLOVES.

Specyfikacje produktu

Marka: Ozito
Kategoria: Maszyna do piłowania
Model: EPP-750

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ozito EPP-750, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Maszyna do piłowania Ozito

Ozito

Ozito PXBCS-1830 Instrukcja

24 Grudnia 2024
Ozito

Ozito PXCCSK-4182 Instrukcja

8 Października 2024
Ozito

Ozito PXBPCK-1825 Instrukcja

8 Października 2024
Ozito

Ozito PXTCSK-2520 Instrukcja

8 Października 2024
Ozito

Ozito PXPRSS-018 Instrukcja

7 Października 2024
Ozito

Ozito PXBPCS-1815 Instrukcja

7 Października 2024
Ozito

Ozito JSW-6100U Instrukcja

22 Września 2024
Ozito

Ozito OCS-018 Instrukcja

20 Września 2024
Ozito

Ozito RSW-5200 Instrukcja

18 Września 2024
Ozito

Ozito JSW-4000U Instrukcja

18 Września 2024

Instrukcje Maszyna do piłowania

Najnowsze instrukcje dla Maszyna do piłowania

Alpina

Alpina APR 26 Instrukcja

22 Marca 2025
Gamma

Gamma HCZ2-85 Instrukcja

11 Marca 2025
Baumr-AG

Baumr-AG SW1 Instrukcja

10 Marca 2025
Stiga

Stiga PR 100e Instrukcja

9 Marca 2025
Bosch

Bosch EasyChain 18V-15-7 Instrukcja

27 Lutego 2025
Worx

Worx Nitro WX501 Instrukcja

26 Lutego 2025
DeWalt

DeWalt DCS383 Instrukcja

12 Lutego 2025
EGO

EGO PSX2510 Instrukcja

6 Lutego 2025
Hilti

Hilti WSR 1400-PE Instrukcja

4 Lutego 2025
Husqvarna

Husqvarna 455e Rancher Instrukcja

12 Stycznia 2025