Instrukcja obsługi Ozito CCS-085

Ozito Maszyna do piłowania CCS-085

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ozito CCS-085 (8 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
CHAINSAW
CHAIN
SHARPENER
85W
INSTRUCTION MANUAL
SPECIFICATIONS
Voltage: 220-240V ~ 50Hz
Motor: 30W (S1), 85W (S2: 15min)
No Load Speed: 5,800/min
Table/Vice: 0 -35 left & right° °
Sharpening Wheel: Ø108 x 3.2 x Ø23mm
Bore: 23mm
Suits Chain Pitch: 0.325" and 3/8"
Tool Weight: 2.0kg
CCS-085
STANDARD EQUIPMENT
3 YEAR REPLACEMENT WARRANTY*
Your product is guaranteed for a period of If 36 months from the original date of purchase.
a product is defective it will be replaced in accordance with the terms of this warranty. Warranty
excludes consumable parts, for example: Sharpening wheel.
*This product is intended for DIY use only and replacement warranty covers domestic use.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other than that specified on the tool.
• If the tool shows signs of damage or defects caused by or resulting from abuse, accidents
or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WARRANTY
Ozito Industries Pty Ltd 25 Fox Drive, Dandenong South, Victoria, Australia 3175.
ozito.com.au
Chainsaw Chain Sharpener
Sharpening Wheel
1021
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY
YOU MUST RETURN THE PRODUCT TO YOUR NEAREST
BUNNINGS WAREHOUSE WITH YOUR BUNNINGS
REGISTER RECEIPT. PRIOR TO RETURNING YOUR
PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR
CUSTOMER SERVICE HELPLINE:
Australia: 1800 069 486
New Zealand: 0508 069 486
The benefits provided under this warranty are in addition to other rights and remedies which
are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this warranty,
however, where you have suffered any additional direct loss as a result of a defective product
you may be able to claim such expenses by contacting our customer service helpline above.
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE
THE MODEL NUMBER AND DATE OF PURCHASE
AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE
WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS
YOU MAY HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
Table/Vice
1. Lowering hand piece
2. Sharpening wheel cover
3. Direction of rotation arrow
4. Sharpening wheel
5. Depth of grind knob
6. Depth of grind lock nut
7. Chain stop knob
8. Chain stop lock nut
9. Chain (tooth) stop
10. Guide
11. Depth stop platform
12. Guide clamp lever
13. Table scale
14. Table
15. Table locking knob
16. Sharpener base
17. Bench mounting holes
CHAINSAW CHAIN SHARPENER
KNOW YOUR PRODUCT
1. ASSEMBLY
1
2
3
4
5
6
7 8
12
10 11
ONLINE MANUAL
Scan this QR Code with your mobile
device to take you to the online manual.
Fitting the Table
1. Insert the bolt of the table
through the hole in the
sharpener base.
2. Secure the table in place by
fixing the locking knob to the
bolt (by screwing the knob
clockwise).
For safe operation of the sharpener, the base of the tool must be fitted to a
flat, solid, secure surface such as a work bench.
The sharpener base is designed in two halves. The rear half is for fitting
flat to a stable surface and the front is designed to protrude over the edge
of the mounting surface.
The sharpener base should be
fitted to the mounting surface by
sliding the rear half back until
the two ‘steps’ on the base align
with the edge of the mounting
surface. Ensure when mounting,
that the table locking knob is
still easily accessible for when
adjusting the table angles.
15 1613
Two 10mm mounting holes allow
for fixing the base to the mounting
surface (bolts not supplied).
Ensure the mounting surface is
capable of supporting the weight
of the sharpener and chain to be
sharpened.
SETUP & PREPARATION
14
9
17
WARNING!: BEFORE ASSEMBLING, MOUNTING, SETTING OR
MAINTAINING YOUR SHARPENER, MAKE SURE THAT THE
MOTOR IS OFF AND THE TOOL DISCONNECTED FROM THE POWER
SUPPLY TO PREVENT ACCIDENTAL STARTING.
Mounting the Sharpener
1. Open the slide guide
groove by rotating the
guide clamp lever anti-
clockwise.
Note: The guide clamp
lever is spring loaded to
allow repositioning of the
handle. By pulling out the
lever and at the same
time rotate to the opposite
direction, then releasing
will allow you to position the handle again to turn in the desired
direction.
Adjusting the Angle of Cut
2. SETTING OF THE SHARPENER
2. Fit a chain over the guide groove
ensuring the inner side of the
chain sits inside the guide groove.
Ensure the chain hangs freely
over the side of the mounting
surface. The chain should be
fitted so the teeth face the right
hand side of the sharpener and
the chain
can move
freely
in both
directions.
Note. Prior to using the sharpener, several adjustments must be made in
order to sharpen the teeth of the chain effectively.
1. Adjusting the angle of cut.
2. Adjusting the chain (tooth) stop.
3. Adjusting the depth of cut.
Failure to perform these adjustments will result in poor sharpening and
possible damage to the chain being sharpened.
Before making adjustments, always ensure the sharpener has been
disconnected from the power supply.
3. If you know the angle of the
chain, rotate the table to the
same angle as the chain. To
rotate the table loosen the table
lock knob and rotate the table
until the scale indicator lines up
with the scale on the base of
the sharpener.
4. If you do not know the angle of the
chain set, the table angle to 35°.
Take hold of the hand piece and
bring it down so that the wheel is
slowly lowered into the chain, along
the cutting tooth. Slowly move the
table so the cutting face of the
tooth is parallel with the edge of
the wheel. The most common chain
angles are 30 – 35°. It may be
necessary to slide the chain slightly
to allow the wheel to enter down
the face of the tooth.
5. Once the correct angle as
been achieved tighten the
table locking knob to lock
the table in the current
position.
After the table is locked in
the required position, take
hold of the hand piece and
lower the head assembly
until the wheel is aligned
along the tooth of the chain.
Confirm the angle then slide the chain so the face of the tooth is just
touching the face of the wheel.
6. Lock the guide by
rotating the clamping
lever as far as it will go
in a clockwise direction.
Ensure the chain is
clamped firmly into the
sliding guide.
Should the chain still
not be clamped, pull the
clamping lever outwards
(away from the guide),
turn the lever anti-clockwise 1/4
of a turn. Push the lever back in
towards the guide. Proceed to
rotate the lever fully clockwise.
Check the chain is clamped. Should
it still not be clamped, repeat the
process above.
WARNING: ALWAYS WEAR HEAVY GLOVES WHEN
HANDLING THE CHAIN.

Specyfikacje produktu

Marka: Ozito
Kategoria: Maszyna do piłowania
Model: CCS-085

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ozito CCS-085, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Maszyna do piłowania Ozito

Ozito

Ozito PXBCS-1830 Instrukcja

24 Grudnia 2024
Ozito

Ozito PXCCSK-4182 Instrukcja

8 Października 2024
Ozito

Ozito PXBPCK-1825 Instrukcja

8 Października 2024
Ozito

Ozito PXTCSK-2520 Instrukcja

8 Października 2024
Ozito

Ozito PXPRSS-018 Instrukcja

7 Października 2024
Ozito

Ozito PXBPCS-1815 Instrukcja

7 Października 2024
Ozito

Ozito JSW-6100U Instrukcja

22 Września 2024
Ozito

Ozito OCS-018 Instrukcja

20 Września 2024
Ozito

Ozito RSW-5200 Instrukcja

18 Września 2024
Ozito

Ozito JSW-4000U Instrukcja

18 Września 2024

Instrukcje Maszyna do piłowania

Najnowsze instrukcje dla Maszyna do piłowania

Alpina

Alpina APR 26 Instrukcja

22 Marca 2025
Gamma

Gamma HCZ2-85 Instrukcja

11 Marca 2025
Baumr-AG

Baumr-AG SW1 Instrukcja

10 Marca 2025
Stiga

Stiga PR 100e Instrukcja

9 Marca 2025
Bosch

Bosch EasyChain 18V-15-7 Instrukcja

27 Lutego 2025
Worx

Worx Nitro WX501 Instrukcja

26 Lutego 2025
DeWalt

DeWalt DCS383 Instrukcja

12 Lutego 2025
EGO

EGO PSX2510 Instrukcja

6 Lutego 2025
Hilti

Hilti WSR 1400-PE Instrukcja

4 Lutego 2025
Husqvarna

Husqvarna 455e Rancher Instrukcja

12 Stycznia 2025