Instrukcja obsługi OSD Audio VMS100


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla OSD Audio VMS100 (1 stron) w kategorii Kontroler. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/1
L+ L- R- R+
INPU T OU TPU T
INPU T OU TPU T
L+ L- R- R+
L+ L- R- R+L+ L- R- R+
RECEIVER/AMPLIFIER
SPEAKER OUTPUTS
L+ L- R - R+
2x 4x 8x 16x
2x 4x 8x 16x
No. of 8 ohm pairs
Switch Settings
1-2 3-4 5-8 9-16
2x 4x 8x 16x
Installation Instruction for the VMS-100
The VMS-100 is simple to install. Pay attention to the following steps:
- Red/Black = right speaker Red = positive [ + ] Black = ground [ - ]
- White/Green = left speaker White = positive [ + ] Green = ground [ - ]
OSD AUDIO • 1405 Pioneer Street • Brea • CA 92821 www.osdaudio.com
A U D I O
OSD
To prevent from overloading
and damaging the amplifier,
the switch must be set
correctly to match the
impedance of the speaker
system to a level equal to or
greater than the impedance
of the amplifier.
Find out the minimum impedance of the amplifier. This
information may be found in the manual or on the back of
amplifier, near the speaker terminals. It is measured in
ohms.
Determine the correct switch setting using the chart
below.
Figure out the total number of speaker pairs to be used.
Set the switch. Make sure that each volume control’s
switch setting is consistent throughout the whole system.
Make sure to use the integral strain reliefs where appropriate when
routing the cable in the J-box.
Strip the insulation off the end of each of the eight individual wires
( four from the amplifier and four to the speakers ) at about 1/4”.
Twist exposed ends together.
Connect the speakers wires to the connector labeled Output
L [ + , - ] and R [ + , - ]. Speaker wires typically use the
following color configuration.
Insert the volume control into the J-box. Mount carefully, making
sure that no wires are pinched or shorted.
VMS-100 Slider
Impedance Matching Slider Stereo Volume Control
Mark the input and output cables accordingly for easy installation.
OSD Audio will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts,
free of charge in the USA, for five years from the date of original purchase. This warranty does not cover damages in shipment, failures caused by
other products not supplied by OSD Audio or failures due to accident, misuse, or alteration of the equipment. This warranty is extended only to the
original purchaser, and a purchase receipt, invoice, or other proof or original purchase date will be required before warranty repairs are provided.
Mail in service can be obtained during the warranty period by emailing RMA@osdaudio.com. A Return Authorization (RMA) number must be
obtained in advance and be marked on the outside of the shipping carton.
This warranty gives you specific legal rights, and may have other rights ( which vary from state to state ). If a problem with this product develops
during or after the warranty period please contact OSD Audio, your dealer, or any factory-authorized service center.
OSD Audio Limited Warranty
Connect the leads from amplifier to the volume control connector
according to the labeled Input L [ + , - ] and R [ + , - ].
1.
2.
3.
4.
1.
2.
3.
4.
5.
6.
7.
2x 4x 8x 16x
INPU T
L+ L- R- R+
OUT PU T
L+ L- R- R+
Input
Out p ut
1
®


Specyfikacje produktu

Marka: OSD Audio
Kategoria: Kontroler
Model: VMS100

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z OSD Audio VMS100, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Kontroler OSD Audio

OSD Audio

OSD Audio VMS100 Instrukcja

21 Września 2024
OSD Audio

OSD Audio OVC300 Instrukcja

20 Września 2024
OSD Audio

OSD Audio SLK100 Instrukcja

20 Września 2024
OSD Audio

OSD Audio SLS100 Instrukcja

19 Września 2024
OSD Audio

OSD Audio OVC100 Instrukcja

18 Września 2024
OSD Audio

OSD Audio VMS300 Instrukcja

18 Września 2024
OSD Audio

OSD Audio NERO VOX Instrukcja

18 Września 2024
OSD Audio

OSD Audio SLK300 Instrukcja

17 Września 2024

Instrukcje Kontroler

Najnowsze instrukcje dla Kontroler