Instrukcja obsługi Nxg NX-W5.2-LCR-P

Nxg głośnik NX-W5.2-LCR-P

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Nxg NX-W5.2-LCR-P (2 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Where To Place Your In-Wall Speakers
Placement can make all the difference in how your speakers sound, and how easy they will be
to install. Carefully consider where your speakers should be positioned. For optimum perform-
ance in a center-channel application, speaker should be mounted directly above or below TV
or monitor. For optimum performance when used in right and left main listening positions,
speakers should be mounted to the left and right of the main listening position and a minimum
of 8 to 10 feet apart (See Fig. 2). Avoid mounting speakers in stud cavities containing electrical
wiring, heating ducts, water pipes, etc. Make sure the wall or ceiling materials are sturdy enough
to support the weight of the speakers.
Note: When the NX-W5.2-LCR-P is mounted horizontally in a center-channel application, modifi-
cation may need to be made to the stud cavity to accommodate speaker.
Pivoting Tweeter (Fig. 3)
The tweeter in the NX-W5.2-LCR-P speaker may be adjusted, allowing you to tailor the speaker
to better fit the listening area. The overall smoothest response is achieved with the tweeter fac-
ing straight out: however, you may find the sound more pleasing by aiming the tweeter toward
a particular listening area. To adjust the tweeter angle, apply pressure on the ring surrounding
the tweeter with your thumb or finger.
Tweeter Level Adjustments (Fig. 4)
The tweeter level control allows you to tailor the speakers’ frequency response to better match
the room’s acoustics. As an example, if a room has a hardwood floor, which makes it acoustical-
ly brighter sounding, you may want to adjust the tweeter level down to compensate. You can
experiment to find the sound that’ most pleasing to you in your particular listening environment. s
Speaker Installation In Existing Construction (See Fig. 5)
Once you have selected the location for your speakers, you are ready to install them.
You will need the following:
• Stud Finder • Drill & Drill Bits • Wire Cutter/Strippers
• Pencil • Utility Knife or Drywall Saw • Small Level
• Masking Tape • Phillips Screwdriver • Speaker Wire
NXG recommends the use of 16-gauge wire minimum. For wire options consult your retailer
or custom audio contractor.
1. NXG Architectural Speakers are designed to be installed in the wall area between studs.
Using a stud finder, make sure you are between two studs. Using the supplied template and a
level to ensure your template is straight, tape the template to the wall and lightly trace around the
inside with a pencil.
2. Cut the hole using your drywall saw. You may want to start with a small hole in the center of
the outline. This will allow you to check for any obstructions that may exist behind the desired
location. CAUTION: Be certain electrical wiring, water pipes or heating ducts do not interfere in
the planned installation areas prior to drilling or cutting the wall.
3. Run speaker wire from your amplifier or speaker switching device to the speaker location.
4. Remove the grille from the speaker. If you like the standard white finish of your NXG In-Wall
Speakers, skip to step 5, but if if you want your speakers to blend in with a colored wall, now is
the time to paint your speakers outer frames and perforated grilles. The speakers outer surfaces
will accept ordinary latex wall paint or aerosol spray paint. Because the surface behind the grille
should remain unpainted, you will need to cover this area. Cover the speaker’s interior black
surface, woofer and tweeter. Paint the outer speaker frame and grille separately.
5. Attach the wire to the input terminals on the rear of the speaker. Remember to maintain
proper polarity with the amplifier by attaching the positive (+) lead to the red terminal and the
negative (-) lead to the black terminal.
Congratulations on choosing NXG In-Wall Loudspeakers. Like all NXG products, great care has
been taken in their design. Their combination of advanced engineering and state-of-the-art mate-
rials will provide you with years of listening pleasure, while blending smoothly into your home’s
decor. Before you get started, it is a good idea to identify all the parts and hardware (See Fig. 1).
FIG. 2
4
3
2
2
1
1
FIG. 3
Press on the
outer edge
of the tweeter
rim to rotate
NX-W5.2-LCR-P Video-Shielded Center/Left/Right In-Wall
Home Theater Speaker System
3
(Continued on reverse)
NXG In-Wall Speakers can be used as rear
surround sound channels by placing them (1) behind,
(2) on each side of viewer, or (3) as front main
home theater speakers. They also can be mounted
horizontally for a center-channel application (4).
Adjust
tweeter level
as shown
FIG. 4
FIG. 1
Speaker with
self-contained
mounting clamps
Cutout Template
Aluminum Grille with
foam inner backing
Grille
removal
tool
Black
grille
adhesive
Painting Mask
IR Sensor
Knockout
Tweeter Level Switch
FIG. 6
(Continued from front)
NXG Speakers Three-Year Limited Warranty
If the NXG speaker system proves to be defective in workmanship
or materials within three years from the date of the original cus-
tomer’s purchase, we will, at our option, repair or replace the
defective product.
Limitation of Implied Warranties
Any implied warranties, including warranties of merchantability
and fitness for a particular purpose, are limited in duration to the
length of this warranty.
Exclusion of Certain Damages
NXG’s liability for any defective product is limited to repair or
replacement of the product at our option. NXG shall not be liable for
incidental or consequential damages of any kind or character
because of product defects. Some states do not allow limitations
on how long an implied warranty lasts and/or do not allow the
exclusion or limitation of incidental or consequential damages, so
the above limitations and exclusions may not apply.
This Warranty Does Not Cover:
• Damage caused by abuse, accident, misuse, negligence, or
improper operation.
• Any product whose serial number has been altered, defaced,
or removed.
• Products that have been altered or modified.
• Normal wear and maintenance.
• Damages caused by shipping. (All claims for shipping damage
must be made with the carrier.)
Warranty Service
Warranty service must be performed by an authorized service
center, usually an NXG speaker systems dealer or its authorized
agent. You may obtain a list of authorized service centers by con-
tacting NXG. All warranty repairs must be accompanied by the
original bill of sales. No other document is acceptable or is
required. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
NXG reserves the right to revise speaker system specifications without notice.
New Construction
1. Determine speaker locations and mark them on your plans for future reference.
2. If possible, run speaker wires after HVAC and electrical wiring is in place.
3. Secure speaker wires in place along the run with insulated staples only and
be careful not to pierce the wire’s insulation. Allow a bit of slack for expan-
sion of building materials.
4. The actual speakers should not be installed until the wall board is in place.
In the meantime, leave several feet of wire coiled up and secured at the back
side of the mounting hole.
5. To complete the installation follow steps 2 through 5 above.
FIG. 5
6. See Fig. 6. With the speaker wire attached to the speaker, slide the speaker
up inside the cut-out hole. Center the speaker in the cut-out hole and turn the six
locking screws clockwise until the speaker is drawn up snugly to the wall board
from behind, clamping the speaker in place. Try to tighten each screw equally.
Replace the speaker grill by gently pressing it into place.
NX-W5.2-LCR-P Specifications
Tweeter: 1˝ (25mm) minimum-diffraction, pivoting,
fluid-cooled high tenacity teteron dome
Woofers: Dual magnetically-shielded 51
/4˝ (133mm)
metallic anodized, graphite-filled, injection-molded
RCT cones with rubber surrounds
Crossover: Optimized 12dB Electro Acoustic w/mylar
capacitors, air core inductors, and gold-plated
input terminals
Frequency Response: 45 Hz-22,000 Hz
Impedance: 8 ohms nominal, 6 ohms minimum
Power Handling: 5-120 watts
Sensitivity: 89dB @ 1 watt/1 meter
Grille: Corrosion-resistant, powder-coated aluminum
Overall Dimensions (H x W x D): 75/8˝ x 15˝ x 3 1/2˝
(194 mm x 381 mm x 89 mm)
Cutout Dimensions (H x W): 63/8˝ x 137/8
˝
(162 mm x 352 mm)
Operational Check
After making all connections it’s a good idea to make sure everything is working
properly. Turn on your stereo system making sure the volume control is turned
down and that the balance control is in the center position. Activate a musical
source such as FM, a CD or DVD player. Gently turn up the volume. You should
hear music coming from your new NXG speakers. If no sound is heard from any
or all speakers, switch off the system immediately and check for open or loose
connections, wrong polarity or shorts.
16648 North 94th Street
Scottsdale, AZ 85260
1-800-733-0008

Specyfikacje produktu

Marka: Nxg
Kategoria: głośnik
Model: NX-W5.2-LCR-P

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Nxg NX-W5.2-LCR-P, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Nxg

Nxg

Nxg NX-W5.2-LCR-P Instrukcja

22 Września 2024
Nxg

Nxg NX-W6.2-P Instrukcja

22 Września 2024
Nxg

Nxg NX-C6.2-P Instrukcja

21 Września 2024
Nxg

Nxg Onyx NX-C8.2-ENC-X Instrukcja

20 Września 2024
Nxg

Nxg NX-C8.3-P Instrukcja

20 Września 2024
Nxg

Nxg NX-C8.2-P Instrukcja

18 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Harman Kardon

Harman Kardon Citation One Instrukcja

14 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024