Instrukcja obsługi Moxa INJ-24A-T

Moxa Wzmacniacz sygnału WiFi INJ-24A-T

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Moxa INJ-24A-T (10 stron) w kategorii Wzmacniacz sygnału WiFi. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/10
P/N: 1802000240025
*1802000240025*
INJ- 24A Series
Quick Installation Guide
Moxa High Injector-Power PoE+
Vers 20ion January 4.2, 21
Technical Support Contact Information
www.moxa.com/support
2 . A20 1 Moxa Inc ll rights reserved.
- - 2
Overview
The Moxa INJ- -24A Series high power PoE+injector is a 1-port PoE+
injector that delivers both data and electrical power to Ethernet-enabled
devices using a single Ethernet cable. The INJ-24A can supply up to 36
watts of power in 2- 4-pair mode or 60 watts in pair mode through the
Ethernet port, and can power IEEE 802.3af/at compliant powered devices
(PD), such as wireless access points or IP cameras, eliminating the need
for additional wiring. The INJ it communication, which -24A supports Gigab
is vital for high- -speed and low latency applications. The INJ-24A also
offers a wide operating temperature range of -40 to 75°C, and is designed
to withstand a high degree of vibration and shock. An innovative
hardware design enhances the INJ-24A with flexible options of Mode A
and Mode B PoE powering modes. This makes the INJ-24A perfect for
outdoor field installation of M12-connector wireless APs and IP cameras
which only have 4 pins in the cable. In addition, the - t INJ 24A can resis
3KV surges from the PoE port, protecting s system operation in critical
industrial environments, and complies with CE/FCC and UL standards for
safet y.
Wiring Requirements
WARNING
Do not disconnect modules or wires unless the power supply has
been switched off or the area is known to be non
-
hazardous. The
devices may only be connected to the supply voltage shown on
the type plate. The devices are designed for operation with a
Safety Extra
-Low Voltage. Thus, they may only be c
onnected to
the supply voltage connections and to the signal contact with the
Safety Extra
-Low Voltages (SELV) in compliance with IEC
60950 1.-1/EN 60950-
WARNING
The power for this product is intended to be supplied by a Listed
Power Unit, with output marked LPS, and rated to deliver 24 DC
at a maximum of 3.72 A.
WARNING
This unit is a built
-in type. When the unit is installed in another
piece of equipment, the equipment enclosing the unit must
comply with fire enclosure regulation IEC 60950
- -1/EN60950 1
(or similar regulation).
- - 3
WARNING
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa PoE injector. Calculate the maximum possible
current in each power wire and common wire. Observe all
electrical codes dictating the maximum current allowable for each
wire size.
If the current goes above the maximum ratings, the
wiring could overheat, causing serious damage to your
equipment.
You should also pay attention to the following items:
• Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring
in the same wire conduit. To avoid interference, wires with different
signal characteristics should be routed separately.
• You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring that shares similar electrical characteristics can be
bundled together.
• Keep input wiring and output wiring separated.
• It is strongly advised that you label wiring to all devices in the system
when necessary.
Package Checklist
The Moxa - A INJ 24 Series is shipped with the following items. If any of
these items is missing or damaged, contact a Moxa customer service
representative for assistance.
• - - Moxa INJ 24A High Power PoE+ Injector
• g Quick installation uide (printed)
• Warranty card
Features
High Performance Technology
• 10/100/1000BaseT(X)
• 36 Provides up to watts (2-pair mode) or 60 watts (4- pair mode) per
PoE port
• - Built in 24/48 VDC booster for PoE and PoE+
Innovative Easy Installation
• Selectable PoE Mode A and Mode B connection options
• SmartPoE LED indication

Specyfikacje produktu

Marka: Moxa
Kategoria: Wzmacniacz sygnału WiFi
Model: INJ-24A-T

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Moxa INJ-24A-T, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Wzmacniacz sygnału WiFi Moxa

Moxa

Moxa INJ-24A-T Instrukcja

24 Września 2024
Moxa

Moxa INJ-24A Instrukcja

24 Września 2024
Moxa

Moxa ioLogik E1242 Instrukcja

24 Września 2024
Moxa

Moxa AWK-3121-M12-EU Instrukcja

24 Września 2024
Moxa

Moxa AWK-6222-US-T Instrukcja

24 Września 2024
Moxa

Moxa NPort Express DE-211 Instrukcja

24 Września 2024
Moxa

Moxa AWK-3131-M12-EU Instrukcja

24 Września 2024
Moxa

Moxa AWK-3131-EU Instrukcja

24 Września 2024
Moxa

Moxa AWK-6222-EU-T Instrukcja

24 Września 2024
Moxa

Moxa ioLogik E1510-T Instrukcja

24 Września 2024

Instrukcje Wzmacniacz sygnału WiFi

Najnowsze instrukcje dla Wzmacniacz sygnału WiFi

Hawking Technologies

Hawking Technologies HOW2R1 Instrukcja

14 Października 2024
Planet

Planet WNAP-1110 Instrukcja

10 Października 2024
Netgear

Netgear WN2000RPTv2 Instrukcja

10 Października 2024
Xiaomi

Xiaomi RA75 Instrukcja

9 Października 2024
Cudy

Cudy RE3000 Instrukcja

8 Października 2024
Cudy

Cudy RE1200 Instrukcja

8 Października 2024
Netgear

Netgear EX6170 Instrukcja

8 Października 2024
Extron

Extron FOX 3G HD-SDI SM Instrukcja

8 Października 2024
Extron

Extron FOXBOX Rx VGA MM Instrukcja

8 Października 2024
Extron

Extron FOX 3G HD-SDI P SM Instrukcja

8 Października 2024