Instrukcja obsługi Monacor ELAX-2812BPTZ

Monacor Kamera monitorująca ELAX-2812BPTZ

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Monacor ELAX-2812BPTZ (2 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Mini PTZ ameraC

ELAX-2812BPTZ

Packing details

Camera 1 PCS

1 PCS

Details NO

Manual

2.1 Cable interface

4IN1 Bullet PTZ Camera support with UTC (Video coaxial

control) ,support with 4 video mode output

(AHD ,TVI ,CVI ,CVBS ) , setting via DIP Switch

You can refer to the following figure for multiple function

combination cable informationSee Figure 2-1. there might

be some differences among different serial products

2-2 Cable function explain

2-1 Cable Draft

Power connector

input DC 12V Power

Power

Video

DIP Switch

Video connector

Setting mode with video

NO Connector Function

AHD

TVI

CVI

CVBS

Equipment connect

Quick installation guide

V1.0.0

PREFACE

Important Safety Notices

Summary：

Document describes unpacking inspection device structures

installation and quick configuration tool in details

Signal instruction：

These symbols may appear with meanings as following

The following contents are specification for using the

devices correctly please read these notices and warnings

carefully and obey while using it

Attention：

1.1 Power

1.2 Environment

All installation and operation here should conform to your

local electrical safety codes

Only use a regulated 12 V power supply unit with a

minimum rating of 2 A.

Please protect cable being trampled power or squeezed

especially in the socket, and exit Junction

Avoid focusing on highlight (such as the sun or lights),

otherwise it may cause over explosion phenomenon (this is

not device's problem) or may damage camera's

CMOS.

Please transport and store t under allowable , use he camera

temperat humidityrange. Do not put the device under e and

wet, dusty extremely hot or cold, strong electromag

netic radiation or unstable lighting conditions etc.

Prevent water or other liquid falling into the camera.

P .lease keep the ventilation around the device

No heavy ion or er splash stress, violent vibrat wat are

allowed during the transportationand storage.

When transporting camera, it use company the should

packing or use same quality ma terial packing.

Thunder-proof device to is recommended be adopted

for preventing thunder better.

Special explanation

1.3 Operation and maintenance

Do not dismantle the camera no components inside since

which can be repaired by users.

Do not touch optic the CMOS component directly you can

use the blower to clean the dust on the lens surface If

necessary, clean the dust with please gently dry clothwhich

is slightly wet with alcohol.

Please use For heavy dirt, soft cloth to clean the device.

please put little detergent on thecloth to clean and dry. Do

not use volatile solvent, Alcohol, Benzene or Diluent-such as

sor irritant and abrasiveness cleanser to clean the device.

Otherwise, it will damage the device or weaken camera

working performance.

The material of front cover is optic component please do not

t ouch or clean the surface directly.For cleaning, please

use professional optical cleaning method Inadaptable

cleaning method (e. g. cleaning directly with cloth ) may

result harmful effect on theinfrared function of the in a

camera.

Warning:

Be sure to use all the accessories recommended by

manufacturer and theinstallation and repairs should be

conducted by professionals.

Please make sure the CMOS component is out of

the radiation of laser beam devices. Otherwise it may result

in damage on the component.

Because our company continuously adopts new technolo-

gies product parameterschange without prior notice. Some

function of products may have slight differenceafter the

updates.

For receiving the latest procedures and additiona linstruction

document please contact the company s customer service

department.

If there are any problems while using the camera, please feel

free to contact the supplier or the company's customer

service department.

Because of the real environment and other unstable factors,

some data may be differ-ent with instruction guide. If there

are any questions and disputes please regard the

Company's final explanation as the criterion.

Please follow instruction guide, we are not liable for any

problems caused byman-made damage

This manual is for reference only. slight difference may be

found in users interface

1.1 Checking Steps

When user received the bullet PTZ Camera, please check

whether it has obviously damage on the appearance of

equipment Packing material can stand accidental Crash on

transport. Please open the package and check all the

components are included. Please reference the following

form.

1.2 Accessories

Be sure to use all the accessories recommended by manufac-

turer

Checking Box

Bracket change

The wall wight for install the camera ,must be can stand 3

times as much as the camera .

Pls Choose cleanly ,smooth wall .Drilled hole according with

the bracket hole . Putting with the bulged tubeThen Fixed

the camera under the ceiling .

Pls Choose cleanly ,smooth wall .Drilled hole according with

the bracket hole . Putting with the bulged tube

The fault of the bracket is walled mounted ,For ceilling

mounted ,if need,change it by urself . As picture ,take out 2

bolts ,motion the bracket with180

2.2

Structure size

(Unit: mm)

2-4 Dimension

2-5 Dimension

2-3 Dimension

3-1 Draft dimension

3-2 Dimension

4-1 Equipment change draft

Wall mounted

Ceiling

IR sensitivity

setting

IR Mode setting

call 95

set 71 call N

set 70 call N N : 1.Auto 2,Open ,3 close

Range of settings 1-10

10 = highest sensitivity level

5Factory default

Reset /restart

call 82 or call 62

call 94 or call 74

NO Function command explain

Equipment Install

180°

Take out bolts put on bolt

PTZ control is made via the PTZ menu of the recorder

connected (control protocol "Coax").

To show the camera menu, call up the preset 95.

Camera setting

1、LENS MANUAL

2、EXPOSURE ←

3、BACK LIGHT OFF

4、WHITE BAL ATW

5、DAY&NIGHT COLOR

6、 ←NR

7、SPECIAL ←

8、ADJUST ←

9、 SAVE&END ←EXIT

Setting

1、LENS MANUAL

2、EXPOSURE ←

3、BACK LIGHT OFF

4、WHITE BAL ATW

5、DAY&NIGHT COLOR

6、 ←NR

7、SPECIAL ←

8、ADJUST ←

9、 SAVE&END ←EXIT

1、 ←SHARPNESS AUTO

2、 ←MONITOR LCD

3、LSC ON

4、VIDEO/OUT NTSC

5、 ←RETURN RET

ADJUST

Appendix

Set

ting

5 Main menu-1

5 2 Submenu ADJUST-

When all settings have been made, use EXIT

to exit the menu.

Specyfikacje produktu

Marka:	Monacor
Kategoria:	Kamera monitorująca
Model:	ELAX-2812BPTZ
Kolor produktu:	Biały
Rodzaj zasilania:	DC
Głębokość produktu:	168 mm
Waga produktu:	385 g
Podręcznik użytkownika:	Tak
Technologia łączności:	Przewodowy i Bezprzewodowy
Bluetooth:	Nie
Liczba kamer:	1
Przeznaczenie:	Wewnętrz i na wolnym powietrzu
Zakres temperatur (eksploatacja):	0 - 50 °C
Układ:	Pocisk
Tryb nocny:	Tak
Wi-Fi:	Nie
Przewodowa sieć LAN:	Nie
Model:	Kamera bezpieczeństwa IP
Maks. rozdzielczość:	1920 x 1080 px
Zakres kąta nachylenia:	0 - 55 °
Typ mocowania:	Sufit / Ściana
Długość ogniskowa:	2.8 - 12 mm
Obsługiwane tryby wideo:	1080p
Typ przetwornika obrazu:	CMOS
Suma megapikseli:	2 MP
Zoom optyczny:	4 x
Tryb dzienny / nocny:	Tak
Typ diody LED:	Podczerwień
Min. Oświetlenie:	0.01 lx
Średnica:	68 mm
Wbudowany HDD:	Nie
PTZ:	Tak
Wyjście prądu stałego (w amperach):	0.8 A
Wielkość czujnika CCD:	1/2.9 "
Video detektor ruchu:	Tak
Liczba czujników:	1
Wyjście prądu stałego (w woltach):	12
Zakres przesuwania:	0 - 180 °
Kompensacja oświetlenia tylnego:	Tak
Odległość widzenia nocnego (Night Vision):	25 m
Ilość diod oświetlenia:	6
Liczba soczewek:	1
Kontrola pochylenia kamery:	Tak
Maska prywatności:	Tak
Szybkość pochylenia:	10 °/s
Prędkość przesuwania:	20 °/s
Wyjścia BNC:	1
Kontrola panewki kamery:	Tak