Instrukcja obsługi Milwaukee M18 Fuel 2734-21

Milwaukee Maszyna do piłowania M18 Fuel 2734-21

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Milwaukee M18 Fuel 2734-21 (36 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/36
Cat. No. / No de cat.
2734-20
M18 FUEL 10" DUAL BEVEL COMPOUND SLIDING MITER SAW
SCIE À ONGLETS COMPOSÉS COULISSANTE À DOUBLE
BISEAU DE 254 mm (10") M18 FUEL™
SIERRA DE INGLETE COMPUESTA DESLIZANTE DE BISEL
DUAL DE 254 mm (10") M18 FUEL™
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and specica-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, re and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to
your mains-operated (corded) power tool or bat-
tery-operated (cordless) power tool.
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodied plugs
and matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
When operating a power tool outdoors, use an exten-
sion cord suitable for outdoor use. Use of a cord suit-
able for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
Use personal protective equipment. Always wear
eye protection. Protective equipment such as a dust
mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce
personal injuries.
Prevent unintentional starting. Ensure the switch
is in the o󰀨-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on the
switch or energizing power tools that have the switch
on invites accidents.
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a ro-
tating part of the power tool may result in personal injury.
Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair can
be caught in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action c
an cause
severe injury within a fraction of a second.
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn
it on and o󰀨. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Pow-
er tools are dangerous in the hands of untrained users.
Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may a󰀨ect
the power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
Use the po
wer tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations di󰀨erent
from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of re when used
with another battery pack.
Use power tools only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and re.
When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a re.
Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact acci-
dentally occurs, ush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns.
Do not use a battery pack or tool that is damaged or
modied. Damaged or modied batteries may exhibit
unpredictable behavior resulting in re, explosion or
risk of injury.
3
Do not expose a battery pack or tool to re or exces-
sive temperature. Exposure to re or temperature
above 265°F (130°C) may cause explosion.
Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specied in the instructions. Charging im-
properly or at temperatures outside the specied range
may damage the battery and increase the risk of re.
SERVICE
Have your power tool serviced by a qualied repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
MITER SAWS
Miter saws are intended to cut wood or wood-like
products, they cannot be used with abrasive cut-o󰀨
wheels for cutting ferrous material such as bars,
rods, studs, etc. Abrasive dust causes moving parts
such as the lower guard to jam. Sparks from abrasive
cutting will burn the lower guard, the kerf insert and
other plastic parts.
Use clamps to support the workpiece whenever
possible. If supporting the workpiece by hand,
you must always keep your hand at least 100 mm
from either side of the saw blade. Do not use this
saw to cut pieces that are too small to be securely
clamped or held by hand. If your hand is placed too
close to the saw blade, there is an increased risk of
injury from blade contact.
The workpiece must be stationary and clamped or
held against both the fence and the table. Do not
feed the workpiece into the blade or cut freehand”
in any way. Unrestrained or moving workpieces could
be thrown at high speeds, causing injury.
Push the saw through the workpiece. Do not pull
the saw through the workpiece. To make a cut, raise
the saw head and pull it out over the workpiece
without cutting, start the motor, press the saw head
down and push the saw through the workpiece.
Cutting on the pull stroke is likely to cause the saw
blade to climb on top of the workpiece and violently
throw the blade assembly towards the operator.
Never cross your hand over the intended line of
cutting either in front or behind the saw blade.
Supporting the workpiece “cross handed” i.e. holding
the workpiece to the right of the saw blade with your
left hand or vice versa is very dangerous.
Do not reach behind the fence with either hand
closer than 100 mm from either side of the saw
blade, to remove wood scraps, or for any other
reason while the blade is spinning. The proximity
of the spinning saw blade to your hand may not be
obvious and you may be seriously injured.
Inspect your workpiece before cutting. If the
workpiece is bowed or warped, clamp it with the
outside bowed face toward the fence. Always make
certain that there is no gap between the workpiece,
fence and table along the line of the cut. Bent or
warped workpieces can twist or shift and may cause
binding on the spinning saw blade while cutting. There
should be no nails or foreign objects in the workpiece.
Do not use the saw until the table is clear of all tools,
wood scraps, etc., except for the workpiece. Small
debris or loose pieces of wood or other objects that con-
tact the revolving blade can be thrown with high speed.
Cut only one workpiece at a time. Stacked multiple
workpieces cannot be adequately clamped or braced
and may bind on the blade or shift during cutting.
Ensure the miter saw is mounted or placed on a level,
rm work surface before use. A level and rm work sur-
face reduces the risk of the miter saw becoming unstable.
Plan your work. Every time you change the bevel
or mitre angle setting, make sure the adjustable
fence is set correctly to support the workpiece and
will not interfere with the blade or the guarding
system. Without turning the tool “ON” and with no
workpiece on the table, move the saw blade through
a complete simulated cut to assure there will be no
interference or danger of cutting the fence.
Provide adequate support such as table extensions,
saw horses, etc. for a workpiece that is wider or
longer than the table top. Workpieces longer or
wider than the miter saw table can tip if not securely
supported. If the cut-o󰀨 piece or workpiece tips, it can
lift the lower guard or be thrown by the spinning blade.
Do not use another person as a substitute for a
table extension or as additional support. Unstable
support for the workpiece can cause the blade to bind
or the workpiece to shift during the cutting operation
pulling you and the helper into the spinning blade.
The cut-o󰀨 piece must not be jammed or pressed
by any means against the spinning saw blade. If
conned, i.e. using length stops, the cut-o󰀨 piece could
get wedged against the blade and thrown violently.
Always use a clamp or a fixture designed to
properly support round material such as rods or
tubing. Rods have a tendency to roll while being cut,
causing the blade to “bite” and pull the work with your
hand into the blade.
Let the blade reach full speed before contacting the
workpiece. This will reduce the risk of the workpiece
being thrown.
If the workpiece or blade becomes jammed, turn
the mitre saw o󰀨. Wait for all moving parts to stop
and disconnect the plug from the power source
and/or remove the battery pack. Then work to
free the jammed material. Continued sawing with
a jammed workpiece could cause loss of control or
damage to the miter saw.
After nishing the cut, release the switch, hold
the saw head down and wait for the blade to stop
before removing the cut-o󰀨 piece. Reaching with
your hand near the coasting blade is dangerous.
Hold the handle rmly when making an incomplete
cut or when releasing the switch before the saw
head is completely in the down position. The
braking action of the saw may cause the saw head to
be suddenly pulled downward, causing a risk of injury.
WARNING
To reduce the risk of injury in ap-
plications that produce a consid-
erable amount of dust, use an OSHA compliant
dust extraction solution in accordance with the
solution’s operating instructions.
Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
Maintain labels and nameplates. These carry
important information. If unreadable or missing, contact
a MILWAUKEE service facility for a free replacement.
4
7
11
1
22
21
15 12 10 9
6
5
2
13
16
3
17
18
19
20
8
14
4
1. Saw head
2. Trigger handle
3. Lower guard
4. Fence hand holds
5. Fences (2)
6. Turntable
7. Mounting holes (4)
8. Miter lock lever
9. Detent lever
10. Detent override knob
11. Kerf plate
12. Miter angle pointer
FUNCTIONAL DESCRIPTION
WARNING
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
lead from lead-based paint
crystalline silica from bricks and cement and other
masonry products, and
arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
lter out microscopic particles.
13. Miter angle scale
14. No Hands Zone circle
15. Carrying handles
16. Fence lock knobs (2)
17. Face board mounting holes (4)
18. Workpiece clamp
19. Slide rails
20. Bevel angle pointers (2)
21. Bevel angle scale
22. Head lock-down pin
6
ASSEMBLY
Installing the Carrying Handles
The carrying handles are used for transport as well
as support extensions for cutting longer workpieces.
Use the four bolts to attach the carrying handles to
each side of the miter saw table, using the blade
wrench provided. Tighten securely.
Always lock the slide rails and lock down the saw
head before transporting tool. Only carry tools by
the carrying handles.
Installing the Kickstand
Lay the miter saw on its side. Insert the kickstand
(the bend should angle toward the ground) into the
two holes under the slide rails. Push the kickstand
in until it won't go any further. To secure, insert and
tighten the screw into the end of one kickstand prong.
Transporting and Storing
Always lock the saw head and slide rails before
transporting and storing the tool.
Saw Head
To lock, press and hold down the saw head and then
push in the lock-down pin.
To unlock, press and hold down the saw head and
pull out the lock-down pin. Raise the saw head.
Slide Rails
To unlock, loosen the slide rail lock by turning it
counterclockwise. NOTE: If the slide does not appear
to work when the slide rail lock is loosened, the chop
lock may be locked.
To lock, slide the saw head forward and tighten the
slide rail lock by turning it clockwise. CAUTION! Do
not use the chop lock to lock the rails for transport.
Mounting the Miter Saw
To prevent the tool from sliding, falling or tipping
from a raised work surface during operation, the saw
should be mounted to a supporting surface such as
a level, sturdy work table, bench, or miter saw stand.
Position the saw and workbench to allow adequate
room for cross-cutting long workpieces. To mount
the saw to a at surface, insert fasteners through
the holes in the corners of the saw base and secure.
Follow manufacturer instructions when mounting to
a miter saw stand.
Dust collection
WARNING
Collected sawdust from coated
(polyurethanes, linseed oil, etc.)
workpieces can self-ignite in the dust bag or
elsewhere and cause re. To reduce the risk of
re, empty the dust bag frequently and never
store or leave a saw without totally emptying its
dust bag.
The dust port at the back of the saw can be con-
nected to a standard workshop vacuum hose or the
included dust bag. Leave the dust bag open to direct
dust down into a garbage can.
To install, push and twist the hose or dust bag onto
the dust port.
Using Face Boards
When using face boards, secure them using the
mounting holes in the fences. Face boards place dis-
tance between the fence and the workpiece, providing
improved support for some workpieces. Workpiece
splintering can be reduced by using face boards.
Selecting, Installing, and Changing Blades
Always use clean, sharp blades. Dull blades tend to
overload the tool, bind, and cause pinching. Use only
10" sliding miter saw blades rated at least 4000 RPM.
Outer
ange
Blade
bolt
Blade
Guard in
blade-changing
OPEN position
1. Remove battery pack.
2. Lower the saw head.
3. Raise the lower guard and hold up while raising
the saw head. Let go of the lower guard. The lower
guard will remain up in the blade-changing OPEN
position. WARNING! Be careful not to lower the
guard head while changing the blade; the lower
guard will fall back into place to cover the blade
and could pinch hands and ngers.
4. Press in the spindle lock and rotate the spindle/
blade until the lock engages.
5. left-hand Use the wrench to loosen and remove the
thread blade bolt (clockwise).
6. Remove the outer blade ange and blade. Wipe
the anges and spindle to remove dust and debris.
Inspect the parts for damage. Replace if needed.
7. Match the arrow direction on the blade with the
arrow direction on the lower guard. Slide the blade
onto the spindle.
8. Install the outer blade ange. The at side of the
ange must rest against the blade.
9. Press in the spindle lock and rotate the blade until
the lock engages. Insert and securely tighten the
blade bolt (counterclockwise) with the wrench.
10. Move hands out of the guard area and lower
the saw head. The lower guard will fall back into
place; verify it moves freely.
11. Check the clearance between the blade, kerf
plate, and fences. Always use the kerf plate. Kerf
plates reduce tear-out and splintering along the
cut by providing edge support.
WARNING
Recharge only with the charger
specied for the battery. For spe-
cic charging instructions, read the operators
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
Always remove battery pack before
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
Only use accessories specically
recommended for this tool. Others
may be hazardous.
8
Adjusting the Fences
Every time the bevel or mitre angle settings are changed,
make sure the fences are set correctly.
Fences :MUST
Support the workpiece
Not interfere with the blade or lower guard
Be adjusted to keep hands out of the No Hand Zone
To adjust the Fences
1. Remove battery pack.
2. Loosen the fence lock knobs.
3. Slide the fences side-to-side to the desired posi-
tion to allow for a bevel or compound miter cut.
Position the fences properly for maximum work
support while maintaining hand safety. WARNING!
Ensure fence hand holds are positioned to keep
hands out of the No Hand Zone.
4. Tighten the fence lock knobs securely before mak-
ing a cut.
NOTE: If either fence has any movement forward
to backward, tighten the fence set screw, located
on the back of each fence slot.
5. With the saw OFF and the workpiece removed
from the table, slowly lower the saw head com-
pletely to ensure the guard and blade do not con-
tact the fences when making miter and bevel cuts.
Guards
The lower guard should cover the blade when the
saw head is up and it should move freely and open
automatically as the saw head is lowered into the
workpiece. WARNING! Never disable or remove
guards. Only push the lower guard into the OPEN
position when changing blades.
If the lower guard appears loose, sticks, or does not
cover the blade when the saw head is up, take the saw
to an authorized service center for repairs.
Ensure the Fences are adjusted properly to allow for
free-movement of the guards during the complete
movement of the cut.
Setting for Chop Cuts
The slides can be locked and the saw head set in
the proper position to use the saw for chop cuts (cuts
not requiring the use of the slides).
1. , push Chop Lock to . To lock
2. Slide saw head until it locks into place.
3. , push Chop Lock to .To unlock
Adjusting the Depth of Cut
The depth of the cut can be adjusted for groove or
rabbet cuts.
1. Remove battery pack.
Depth-stop lever
Lock nut
Knob
2. To set the depth of cut,
rotate the depth stop
lever up.
3. Lower the saw head to
the desired depth of cut.
4. Rotate the depth stop
adjustment knob un-
til it contacts the le-
ver. Lock in the depth
us ing the l ock nut.
5. Make a test cut to verify
the depth of cut is cor-
rect.
6. To remove the depth
of cut limit, loosen the
lock nut by turning counterclockwise and rotate
the lever back.
OPERATION
WARNING
To reduce the risk of injury, always
wear proper eye protection marked
to comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Keep hands and body out of the path of the saw
blade. Contact with blade will result in serious
injury. Check guarding system to make sure it is
functioning correctly. Do not operate saw without
guards in place. Do not perform any operation
freehand. Never reach around saw blade. Turn
o󰀨 tool and wait for saw blade to stop before
moving workpiece or changing settings. Tighten
all adjustments prior to use.
Cut Line Indicator
The cut-line indicator shines down the blade, casting
a shadow where the blade will meet the workpiece.
No calibration/adjustments will be needed as the
shadow will always be true to the blade location.
Use the cut-line indicator switch to turn on the light
before making a cut. The light will go o󰀨 automatically
about 10 seconds after use.
WARNING
To reduce the risk of injury, do not
rely on the brake as a safety fea-
ture. Always wait until the blade stops com-
pletely before allowing anything near the blade.
To reduce the risk of injury, make sure all adjust-
ments are securely locked before making a cut.
Starting and Stopping the Tool
Always hold the trigger handle rmly because the
starting and stopping action of the motor may cause
the handle to move up or down slightly. WARNING!
Always press down miter lock lever and tighten all
adjustments prior to use. WARNING! Ensure hands
are out of the No Hands Zone.
1. To start the motor, push down the trigger lock and
pull the trigger.
2. To stop the motor, release the trigger. The elec-
tric brake will stop the blade in about 4 seconds.
WARNING! The brake is not a substitute for the
guards and could fail; always wait for the blade to
stop completely before removing the blade from
the workpiece. If the brake fails to stop the blade or
misses frequently, return the tool to a MILWAUKEE
service facility for repair.
Making a Chop Cut
Cut workpieces with chop cuts whenever possible.
Only use sliding cuts (cross cuts) when necessary.
1. Use the chop lock to set the saw in the chop cut
position.
2. Select the desired angles and adjust the fences to
ensure fence hand holds are positioned to keep
hands out of the No Hand Zone.
3. Place the workpiece on the turntable and line up
the cut.
4. Insert battery pack.
5. Support the workpiece using any of the methods
described in "Support the Workpiece Properly".
6. WARNING! Keep hands out of the No Hands
Zone at all times during use. Contact with blade
will result in serious injury.
9
7. Start the motor. Wait a few seconds for the blade
to reach full speed. Then gently lower the saw
head into the workpiece all the way through the
cut. WARNING! Do not allow the blade to contact
the workpiece while tool is ramping up.
8. Always allow the saw to do the work. Forcing the
tool may stall or overheat the motor.
9. After the cut is complete, release the trigger and
wait for the blade to stop completely. Raise the
saw head and remove the workpiece. WARNING!
If small cut-o󰀨 pieces get caught in the guard area,
remove battery pack before clearing.
Making a Sliding Cut (Cross Cut)
Wider workpieces can be cut using the sliding
mechanism. Always use chop cut whenever possible.
4
2
3
1
1. Make sure that the chop lock is unlocked, the
slide rail transport lock is loose, and the saw head
moves freely back and forth.
2. Select the desired angles and adjust the fences to
ensure fence hand holds are positioned to keep
hands out of the No Hand Zone.
3. Place the workpiece on the turntable and line
up the cut.
4. Insert battery pack.
5. Support the workpiece using any of the methods
described in "Support the Workpiece Properly".
6. WARNING! Keep hands out of the No Hands
Zone at all times during use. Contact with blade
will result in serious injury.
7. -Raise saw head and pull it out OVER the work
piece WITHOUT cutting.
8. Start the motor. Wait a few seconds for the blade
to reach full speed. WARNING! Do not allow
the blade to contact the workpiece while tool is
ramping up.
9. Press down on saw head.
10. Push saw through the cut. WARNING! Return saw
head to the full rear position after each crosscut
operation.
11. After the cut is complete, release the trigger and
wait for the blade to stop completely. Raise the
saw head and remove the workpiece. WARNING!
If small cut-o󰀨 pieces get caught in the guard area,
remove battery pack before clearing.
APPLICATIONS
WARNING
Do not cut stone, brick, concrete,
magnesium, or ferrous metals
(iron, steel, stainless steel, or alloys of these
metals) with this saw.
Do not use abrasive wheels with this saw.
Dust created by cutting these materials and/or
using abrasive cut-o󰀨 wheels can jam the blade
guard and possibly cause personal injury.
Recommended Materials and Applications
The following materials can be cut with the com-
pound sliding miter saw. There are many types of
saw blades available. Always use the proper blade
for the particular material and application. Use only
10" sliding miter saw blades rated at least 4000 RPM.
Wood - solid wood, plywood, particle board, MDF
(medium density berboard), HDF (high density
berboard), melamine laminated particle board,
formica laminates, hardboard (masonite).
Plastics - PVC, CPVC, ABS, solid surfacing materi-
als (such as Corian
®), and other plastic materials.
When cutting plastic, avoid overheating the blade
and blade teeth to prevent melting the workpiece.
Nonferrous Metals - aluminum, brass, copper, and
other non-ferrous materials.
Cutting Non-Square Materials
Cutting Round (Cylindrical) Materials
"V" shaped blocks can be used to support round
materials like closet rod and plastic pipe.
Aluminum Sash and Other
Channel Type and Materials
Aluminum sash material can be supported with blocks
to prevent it from deforming while it is being cut.
Clamp
Fence
Table
Wood support
block
Aluminum
material
Wood support
block
Miter Range Miter Detents (Stops)
0° to 50° Left
0° to 60° Right
0°, 15°, 22.5°, 31.62°, 45°, 50° Left
0°, 15°, 22.5°, 31.62°, 45°, 60° Right
Bevel Range Bevel Detents (Stops)
0° to 48° Left
0° to 48° Right
0°, 22.5°, 33.85°, 45°, 48° Left
0°, 22.5°, 33.85°, 45°, 48° Right
Base Molding
Capacity
Nested Crown
Capacity
5-3/4" at 0°
5-3/4" at 45° Left
5-3/4" at 45° Right
5-1/4"


Specyfikacje produktu

Marka: Milwaukee
Kategoria: Maszyna do piłowania
Model: M18 Fuel 2734-21

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Milwaukee M18 Fuel 2734-21, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Maszyna do piłowania Milwaukee

Milwaukee

Milwaukee M18 FTCHS14 Instrukcja

9 Października 2024
Milwaukee

Milwaukee MXF COSCG2 Instrukcja

8 Października 2024
Milwaukee

Milwaukee M12 2420-21 Instrukcja

6 Października 2024
Milwaukee

Milwaukee M18 BJS Instrukcja

4 Października 2024
Milwaukee

Milwaukee SCS 65 Q Instrukcja

4 Października 2024
Milwaukee

Milwaukee M12 BS Instrukcja

4 Października 2024
Milwaukee

Milwaukee M18 FMCS66 Instrukcja

4 Października 2024
Milwaukee

Milwaukee M18 BSX Instrukcja

4 Października 2024
Milwaukee

Milwaukee SSPE 1500 X Instrukcja

3 Października 2024
Milwaukee

Milwaukee SSPE 1300 RX Instrukcja

3 Października 2024

Instrukcje Maszyna do piłowania

Najnowsze instrukcje dla Maszyna do piłowania