Instrukcja obsługi Mikrotik CRS328-24P-4S+RM

Mikrotik nieskategoryzowany CRS328-24P-4S+RM

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Mikrotik CRS328-24P-4S+RM (5 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/5

CRS328-24P-4S+RM

CRS328-24P-4S+RMCRS328-24P-4S+RM

CRS328-24P-4S+RM

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

The Installation of the equipment must comply with local and national electrical codes.

This unit is intended to be installed in the rackmount. Please read the mounting instructions carefully before beginning installation. Failure to use the

correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.

This product is intended to be installed indoors. Keep this product away from water, fire, humidity or hot environments.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik devices must be professionally installed.

Quick start

Mount unit in a rackmount cabinet or place on the flat surface (see " ").

Mounting

Connect to the power source (see " ").Powering

The Initial connection has to be done via the Ethernet cable, using the MikroTik Winbox utility.

Set IP for your PC to 192.168.88.2

Use Winbox to connect to the default IP address of 192.168.88.1 from any port, with the username and no password

admin

(or, for some models,

.check user and wireless passwords on the sticker)

Update the device by clicking the "Check for updates" button to v6.46 or the latest RouterOS software to ensure the best performance and

stability. The device needs to have an active internet connection.

To manually update the device, go to our download pagehttps://mikrotik.com/download

Choose your architecture (ARM) and download the latest packages from any channel to your PC.

Open Winbox and upload packages in the Files menu.

Reboot the device.

Updating software will ensure the latest security fixes and regulations set by local law.

Set up your password to secure the device.

Mounting

The device is designed to use indoors and it can be mounted in a rackmount enclosure using provided rack mounts, or it can be placed on the desktop.

Please attach rubber pegs on the bottom of the router if the desired placement is on the flat surface or use a Phillips screwdriver to attach rackmount ears

on both sides of the device if designated use is for rackmount enclosure:

Attach rack ears to both sides of the device and tighten four screws to secure them in place, as shown in the picture.

Place the device in the rackmount enclosure and align with the holes so that the device fits conveniently.

Tighten screws to secure it in place.

The device has no protection from water contamination, please ensure the placement of the device in a dry and ventilated environment.

We recommend Cat6 cables for our devices.

Mounting and configuration of this device should be done by a qualified person.

Powering

The unit is equipped with one IEC type AC power input, which accepts 100-240 V powering (~ 50/60 Hz 7 A max). The power consumption of this device

itself under maximum load is up to 44 W.

Booting process

The device supports booting RouterOS (for complete routing and switching configuration) or SwOS (for only using as a switch). By default, the device will

boot RouterOS, but you can reboot into the other operating system in the following ways:

From SwOS: In the System menu, click the "Boot RouterOS" button on the bottom of the page.

From RouterOS: in the System, RouterBOARD menu, click "Settings" and there select "Boot OS".

It is also possible to select the OS and configure other boot settings via the serial console menu.

Configuration

Full RouterOS and SwOS documentation is located here: https://mt.lv/help

This device is not preconfigured other than an IP address on the master Ethernet port. You can connect from any port, as all ports are switched together

by default. Another configuration has to be applied according to the documentation manual linked above.

The Initial connection has to be done via the Ethernet cable, using the MikroTik Winbox utility. Winbox should be used to connect to the default IP address

of 192.168.88.1 from any port, with the username admin and no password.

For recovery purposes, it is possible to boot the device from the network, see Buttons, and Jumpers.

In case the IP connection is not available, the Winbox utility can also be used to connect to the MAC address of the device. Applies only when the device

has booted RouterOS.

The device is equipped with an RJ45 serial port, set by default to 115200bit/s, 8 data bits, 1 stop bit, no parity. Standard RJ45 to COM cable can be used,

pinout can be found in our manual: https://mt.lv/help

Power output

This device can supply PoE powering to external devices from its Ethernet ports. The output voltage will be selected automatically, depending on what kind

of voltage the connected device requires. The device can power both 802.3af/at devices and devices that accept passive PoE power. If necessary, the

output voltage can be switched manually. By default the PoE mode is set to auto, it will not damage devices and will auto-detect devices with PoE support

and the needed voltage. Once a PoE device is detected, it will be powered and the PoE LEDs will turn on.

The PoE out ports is grouped in three PoE out groups of 8 ports each (PSE8). Total device PoE limit = 450w (150w per PSE8 group).

Each port can provide up to 30 W with high voltage, and 26,5 W with low voltage power output.

Buttons and Jumpers

Reset button

Reset buttonReset button:

Hold this button during boot time until the USR LED light starts flashing, release the button to reset RouterOS configuration.

Keep holding the button for 5 more seconds or until the user LED turns off, then release it to make the RouterBOARD look for Netinstall servers. T

See RouterOS documentation about using the Netinstall recovery utility.

he first Ethernet port is used for the Netinstall process.

he first Ethernet port is used for the Netinstall process.he first Ethernet port is used for the Netinstall process.

Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device.

Release the button before LED begins to flash, to only load backup RouterBOOT without resetting. This is useful for RouterBOOT debugging and recovery.

Mode button:

Mode button:Mode button:

The action of the mode buttons can be configured from RouterOS software to execute any user-supplied RouterOS script. You can also disable this button.

The mode button can be configured in RouterOS menu /system routerboard mode-button

Extension slots and ports

24 gigabit Ethernet ports (With Auto MDI/X so you can use either straight or cross-over cables for connecting to other network devices).

4 SFP+ cages, which accept both 1.25 Gb SFP and 10 Gb SFP+ modules.

RJ45 serial port.

LED indicators

PWR LED is lit when the router is powered on.

The use of LEDs can be configured from RouterOS.

Triangle LEDs (top row) indicate PoE out status. Green LED indicates that the respective port uses low voltage, a red LED indicates high voltage.

Flashing single green LED: problem to start a low voltage device. Flashing single red LED: problem with high voltage device.

The square port LEDs (bottom row) indicate the individual Ethernet, SFP port activity.

FAN FAULT LED indicates a problem with any of the cooling fans.

PoE FAULT LED indicates an exceeded overall max PoE output limit. Port PoE-out priorities will work in 3 independent sections (8 ports each)

and overload will happen in any section that breach 150W consumption

Accessories

Package includes the following accessories that come with the device:

Please visit wiki pages for MikroTik SFP module compatibility table: https://wiki.mikrotik.com/wiki/MikroTik_SFP_module_compatibility_table

Operating system support

The device supports dual boot SwOS software version 2.9 and RouterOS v6. The specific factory-installed version number is indicated in the RouterOS

menu /system resource. Other operating systems have not been tested.

https://wiki.mikrotik.com/wiki/SwOS

Specyfikacje produktu

Marka:	Mikrotik
Kategoria:	nieskategoryzowany
Model:	CRS328-24P-4S+RM
Kolor produktu:	Biały
Napięcie wejściowe AC:	100 - 240 V
Wysokość produktu:	44 mm
Szerokość produktu:	443 mm
Głębokość produktu:	305 mm
Maksymalne zużycie mocy:	44 W
Wielkość pamięci flash:	16 MB
Pojemność pamięci wewnętrznej:	512 MB
Procesor wbudowany:	Tak
Standardy komunikacyjne:	IEEE 802.1Q, IEEE 802.3ad
Obsługa PoE:	Tak
Zakres temperatur (eksploatacja):	-20 - 60 °C
Układ:	1U
Taktowanie procesora:	800 MHz
Przewody:	Prąd przemienny
Kod zharmonizowanego systemu (HS):	85176990
Diody LED:	Tak
Obsługa sieci VLAN:	Tak
Protokoły zarządzające:	SNMP
Możliwości montowania w stelażu:	Tak
Typ przełącznika:	Zarządzany
Podstawowe przełączanie RJ-45 Liczba portów Ethernet:	24
Podstawowe przełączania Ethernet RJ-45 porty typ:	Gigabit Ethernet (10/100/1000)
Wielkość tabeli adresów:	16000 wejścia
Przepustowość rutowania/przełączania:	128 Gbit/s
Lista kontrolna dostępu (ACL):	Tak
Przełącznik wielowarstwowy:	L2/L3
Prędkość przekazywania:	95.2 Mpps
Zgodny z Jumbo Frames:	Tak
Zasilacz dołączony:	Tak
Ilość slotów Modułu SFP+:	4
Port konsoli:	RJ-45
Zestaw do montażu haków:	Tak
Dublowanie portów:	Tak
Kontrola wzrostu natężenia ruchu:	Tak
Przepustowość:	64 Mpps