Instrukcja obsługi Mikrotik CRS317-1G-16S+RM

Mikrotik nieskategoryzowany CRS317-1G-16S+RM

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Mikrotik CRS317-1G-16S+RM (5 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/5

CRS317-1G-16S+RM

CRS317-1G-16S+RMCRS317-1G-16S+RM

CRS317-1G-16S+RM

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

The Installation of the equipment must comply with local and national electrical codes.

This unit is intended to be installed in the rackmount. Please read the mounting instructions carefully before beginning installation. Failure to use the

correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.

This product is intended to be installed indoors. Keep this product away from water, fire, humidity or hot environments.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik devices must be professionally installed.

Quick start

Mount unit in a rackmount cabinet or place on the flat surface (see " ").

Mounting

Connect two powering units to the AC source using power cords.

The Initial connection has to be done via the Ethernet cable, using the MikroTik Winbox utility.

Use Winbox to connect to the default IP address of 192.168.88.1 from any port, with the username and no password

admin

(or, for some models,

. In case the IP is not available please use Neighbors and connect with MAC.check user and wireless passwords on the sticker)

Update the device by clicking the "Check for updates" button to v6.46 or the latest RouterOS software to ensure the best performance and

stability. The device needs to have an active internet connection.

To manually update the device, go to our download pagehttps://mikrotik.com/download

Choose your architecture (ARM) and download the latest packages from any channel to your PC.

Open Winbox and upload packages in the Files menu.

Reboot the device.

Updating software will ensure the latest security fixes and regulations set by local law.

Set up your password to secure the device.

Mounting

The device is designed to use indoors and it can be mounted in a rackmount enclosure using provided rack mounts, or it can be placed on the desktop.

Please attach rubber pegs on the bottom of the router if the desired placement is on the flat surface or use a Phillips screwdriver to attach rackmount ears

on both sides of the device if designated use is for rackmount enclosure:

Attach rack ears to both sides of the device and tighten four screws to secure them in place, as shown in the picture.

Place the device in the rackmount enclosure and align with the holes so that the device fits conveniently.

Tighten screws to secure it in place.

The IP rating scale for this device is IP0. The device has no protection from water contamination, please ensure the placement of the device in a dry and

ventilated environment.

We recommend Cat6 cables for our devices.

The mounting and configuration of this device should be done by a qualified person.

Powering

The device accepts powering through two IEC C14 standard connectors and supports both AC 110/240 V . Only one PSU is active at the time, the second

one is used for redundancy.

The PoE injector is not included. The power consumption of this device under maximum load is up to 44W.

Booting process

The device supports booting RouterOS (for complete routing and switching configuration) or SwOS (for only using as a switch). By default, the device will

boot RouterOS, but you can reboot into the other operating system in the following ways:

From SwOS: In the System menu, click the "Boot RouterOS" button on the bottom of the page.

From RouterOS: in the System, RouterBOARD menu, click "Settings" and there select "Boot OS".

The device is fitted with passive cooling heatsinks and under normal load will operate silently, but in emergencies, two redundant fans will automatically

switch on to keep the device cool, if ambient temperatures are above normal. The device has been tested to operate in ambient temperatures from -20 ℃

to +60 ℃.

Configuration

Full RouterOS and SwOS documentation are located here: .

https://mt.lv/help

This device is not preconfigured other than an IP address on the master Ethernet port. You can connect from any port, as all ports are switched together

by default. Another configuration has to be applied according to the documentation manual linked above.

The Initial connection has to be done via the Ethernet cable, using the MikroTik Winbox utility. Winbox should be used to connect to the default IP address

of 192.168.88.1 from any port, with the username admin and no password.

In case the IP connection is not available, the Winbox tool ( ) can also be used to connect to the MAC address of the device. Applies

https://mt.lv/winbox

only when the device has booted RouterOS.

The device is equipped with an RJ45 serial port, set by default to 115200bit/s, 8 data bits, 1 stop bit, no parity. Standard RJ45 to COM cable can be used,

pinout can be found in the documentation.

Extension slots and ports

One gigabit Ethernet port for management (With Auto MDI/X so you can use either straight or cross-over cables for connecting to other network

devices). The Ethernet port (ETH/BOOT) can be used for network booting.

16 SFP+ cages, which accept both 1.25 Gb SFP and 10 Gb SFP+ modules.

RJ45 serial port.

Reset button

The RouterBOOT reset button has the following functions. Press the button and apply the power, then:

Release the button when green LED starts flashing, to reset RouterOS configuration to defaults.

Release the button when the LED turns solid green to clear all configuration and defaults.

Release the button after LED is no longer lit (~20 seconds) to cause a device to look for Netinstall servers (required for reinstalling RouterOS over

the network).

Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device.

Useful for RouterBOOT debugging and recovery.

SwOS Reset and Reinstall

CRS317-1G-16S+ has built-in backup SwOS firmware which can be loaded in case standard firmware breaks or upgrade fails:

Holding the Reset button for few seconds while CRS317-1G-16S+ is booting resets configuration and loads backup firmware SwOS 2.3p.

After loading back up firmware SwOS 2.3p it is possible to connect to 192.168.88.1 using a web browser and install new SwOS firmware.

Accessories

Package includes the following accessories that come with the device:

Please visit wiki pages for MikroTik SFP module compatibility table: https://wiki.mikrotik.com/wiki/MikroTik_SFP_module_compatibility_table

Specifications

For more information about this product, specification and pictures please visit our web page: https://mikrotik.com/product/crs317_1g_16s_rm

Operating system support

The device supports dual boot SwOS software version 2.9 and RouterOS v6. The specific factory-installed version number is indicated in the RouterOS

menu /system resource. Other operating systems have not been tested.

https://wiki.mikrotik.com/wiki/SwOS

Safety Notice

Electric shock hazard. This equipment is to be serviced by trained personnel only.

Specyfikacje produktu

Marka:	Mikrotik
Kategoria:	nieskategoryzowany
Model:	CRS317-1G-16S+RM
Kolor produktu:	Szary
Napięcie wejściowe AC:	110 - 240 V
Wysokość produktu:	44 mm
Szerokość produktu:	443 mm
Głębokość produktu:	224 mm
Maksymalne zużycie mocy:	42 W
Wielkość pamięci flash:	1000 MB
Pojemność pamięci wewnętrznej:	16 MB
Procesor wbudowany:	Tak
Standardy komunikacyjne:	IEEE 802.1Q
Obsługa PoE:	Nie
Zakres temperatur (eksploatacja):	-20 - 60 °C
Zarządzanie przez stronę www:	Tak
Układ:	1U
Taktowanie procesora:	800 MHz
Przewody:	Prąd przemienny
Kod zharmonizowanego systemu (HS):	85176990
Szyfrowanie / bezpieczeństwo:	SNMPv2, SNMPv3
Diody LED:	Tak
Liczba wentylatorów:	2 went.
Ilość jednostek zasilania:	2
Obsługa sieci VLAN:	Tak
Przewodnik użytkownika:	Tak
Możliwości montowania w stelażu:	Tak
Przycisk reset:	Tak
Typ przełącznika:	Zarządzany
Podstawowe przełączania Ethernet RJ-45 porty typ:	Nie
Złącze zasilania:	DC-in jack
Obsługa 10G:	Tak
Wielkość tabeli adresów:	- wejścia
Przepustowość rutowania/przełączania:	- Gbit/s
Uchwyty mocowania dołączone:	Tak
Przełącznik wielowarstwowy:	L3
Ilość slotów Modułu SFP+:	16
Port konsoli:	RJ-45
Liczba VLANs:	4000
Agregator połączenia:	Tak
Protokół drzewa rozpinającego:	Tak
Dublowanie portów:	Tak
Kontrola wzrostu natężenia ruchu:	Tak
Ilość portów Gigabit Ethernet:	1
Typ pamięci:	Flash