Instrukcja obsługi Maytag XHP1000XW

Maytag Niesklasyfikowane XHP1000XW

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Maytag XHP1000XW (16 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/16
W10178072B
W10348604B-SP
PEDESTAL INSTALLATION INSTRUCTIONS
For use only with front load washers and dryers
INSTRUCTIONS D’INSTALLATION DU PIÉDESTAL
Pour utilisation avec les laveuses et sécheuses à chargement frontal
Table of Contents Table des matières
PEDESTAL SAFETY ......................................................1
INSTALLATION REQUIREMENTS ................................2
Location Requirements .........................................2
Tools and Parts .......................................................2
INSTALLATION INSTRUCTIONS ..................................3
Before Installing Pedestal .....................................3
INSTALLING THE PEDESTAL .......................................4
COMPLETE THE INSTALLATION. ................................5
WARRANTY ...................................................................7
SÉCURITÉ DU PIÉDESTAL ..........................................9
EXIGENCES D’INSTALLATION ....................................9
Exigences d’emplacement ....................................9
Outillage et pièces. ................................................9
INSTRUCTIONS D’INSTALLATION. ...........................10
Avant l’installation du piédestal.. ........................10
INSTALLATION DU PIÉDESTAL .................................11
ACHEVER L’INSTALLATION. ......................................13
GARANTIE ...................................................................15
INSTALLATION NOTES
Date of purchase: _________________________________
Date of installation: _______________________________
Installer: ________________________________________
Model number: ___________________________________
Serial number: ___________________________________
NOTES CONCERNANT L’INSTALLATION
Date d’achat : _____________________________________
Date d’installation : ________________________________
Installateur : ______________________________________
Numéro de modèle : ________________________________
Numéro de série : __________________________________
PEDESTAL SAFETY
Para una versión de estas instrucciones en español, visite www.whirlpool.com
2
Pliers or slip-joint pliers
Utility knife 1/4" hex-head ratchet or
open-end wrench
Towel
9/16" open-end wrench
Sponge
Bucket
Level
INSTALLATION REQUIREMENTS
LOCATION REQUIREMENTS
NOTE: If the washer/dryer and pedestal assembly are located
in a garage, 8 (203 mm) must be added under the pedestal so "
that the washer/dryer is 18 (458 mm) above the garage oor."
TOOLS AND PARTS
Gather the required tools and parts before starting installation.
Tools needed:
Additional items needed:
Four #12 x 5/8 hex-head "
sheet metal screws
(in parts bag)
Two retainer clips
(in parts bag)
Parts supplied:
3
Uninstalling your gas dryer
1. Unplug the power supply cord.
2. Turn off the gas supply.
3. Pull the dryer away from the wall enough to loosen the vent
clamp. Loosen the clamp and gently remove the exhaust vent
from the dryer exhaust outlet.
4. Disconnect the exible gas supply line from the dryer. Put a
piece of tape over the open ends of the gas line connection
ttings.
5. Pull the dryer away from the wall so that it can be tipped on
its back.
6. To avoid oor damage and ease installation and handling,
unfold the empty pedestal box at and place it next to the
dryer. Lay the dryer on its back (make sure that the power
supply cord is not under the dryer) so that the cardboard is
under the entire lower back edge of the dryer. Go to “Installing
the Pedestal”.
Installation of new washer/dryer
INSTALLATION INSTRUCTIONS
BEFORE INSTALLING PEDESTAL
IMPORTANT: If your washer and dryer are already installed,
they must be uninstalled.
Uninstalling your washer
To avoid possible damage to the washer, the transport bolts on
the back of the washer must be in place before installing the
pedestal. For more information on transport bolts, see “Remove
Transport System” in washer Use and Care Guide.
NOTE: If the washer is to be transported, call your local
service center. To avoid suspension and structural damage,
your washer must be properly set up for relocation by a certied
technician.
1. Turn off the hot and cold water faucets.
2. Unplug the power supply cord.
3. Slowly loosen the ll hoses at the faucets to relieve the water
pressure. Use a sponge or towel to absorb the released water.
4. Remove the “HOT” and “COLD” ll hoses from the back of the
washer. Drain the water from the hoses into a bucket.
5. Remove the drain hose from the standpipe or laundry tub
and drain any water remaining in the hose into a bucket.
6. Pull the washer away from the wall so it can be tipped on its
back.
7. To avoid oor damage and ease installation and handling,
unfold the empty pedestal box at and place it next to the
washer. Lay the washer on its back (make sure that the power
supply cord is not under the washer) so that the cardboard is
under the entire lower back edge of the washer.
8. An additional small amount of water will drain out of the
washer when it is tipped back. Go to “Installing the Pedestal”.
Uninstalling your electric dryer
1. Unplug the power supply cord.
2. Pull the dryer away from the wall enough to loosen the vent
clamp. Loosen the clamp and gently remove the exhaust vent
from the dryer exhaust outlet.
3. Pull the dryer away from the wall so that it can be tipped on
its back.
4. To avoid oor damage and ease installation and handling,
unfold the empty pedestal box at and place it next to the
dryer. Lay the dryer on its back (make sure that the power
supply cord is not under the dryer) so that the cardboard
is under the entire lower back edge of the dryer. Go to
“Installing the Pedestal”.
If your washer/dryer is still in the packaging:
Washer: Cut plastic lm along dotted cut line around the base.
Do not remove the packaging.
Dryer: Cut carton around top and down corners along dotted
cut lines. Lay all four carton sides on oor. Discard carton top
and corner posts.
1. Unpacking Washer/Dryer
Washer Dryer
Base

Specyfikacje produktu

Marka: Maytag
Kategoria: Niesklasyfikowane
Model: XHP1000XW

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Maytag XHP1000XW, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Maytag

Maytag

Maytag WHP0400VW Instrukcja

15 Października 2024
Maytag

Maytag MMMS4230PZ Instrukcja

26 Września 2024
Maytag

Maytag MOES6030LZ Instrukcja

25 Września 2024
Maytag

Maytag MGDP586KW Instrukcja

25 Września 2024
Maytag

Maytag MTUC7500AF Instrukcja

25 Września 2024
Maytag

Maytag MALAUMVW7230HC Instrukcja

25 Września 2024
Maytag

Maytag MALAUMGD6630HW Instrukcja

25 Września 2024
Maytag

Maytag MALAUMGD6630HC Instrukcja

25 Września 2024
Maytag

Maytag W10748976 Instrukcja

25 Września 2024
Maytag

Maytag W10915235 Instrukcja

25 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024