Instrukcja obsługi Marantz MOUNT20BL

Marantz Projektor MOUNT20BL

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Marantz MOUNT20BL (6 stron) w kategorii Projektor. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
Model MOUNT20 User Guide
For 11/ /15 eries VP- 12 S Projector
MOUNT20
PROJECTOR MOUNT
INSTALLATION INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ BEFORE INSTALLING EQUIPMENT
This product was designed and manufactured to meet strict
quality and safety standards. There are, however, some
installation and operation precautions which you should be
particularly aware of.
1.
Read instructions -
All the safety and operating instructions
should be read before the product is operated.
2.
Retain instructions -
The safety and operating instructions
should be retained for future reference.
3.
Heed warnings -
All warnings on the product and in the
operating instructions should be adhered to.
4.
Follow instructions -
All installation instructions should
be followed.
5.
Use only the parts provided with the mount, along with any
parts (commercially available) that are specified in this manual.
6.
Do not modify the mount or the parts provided with the mount.
7.
Do not use damaged parts. if any parts become damaged,
contact your dealer.
8.
All bolts and screws must be tightened securely.
9.
Make sure not to block any ventilation openings when installing
the projector.
11.
Once the projector is installed, safety checks should be conducted
on a regular basis.
10.
Special techniques and experience are required when installing
the projector with this mount. Contact your dealer to install the
projector for you.
Warning
Hardware List
Adjustment Ranges and Load Allowances
The ceiling should be capable of supporting a weight
of at least five (5) times the projector(s) weight.
If it cannot, the ceiling must be reinforced. Proper
installation procedure by qualified personnel as outlined
in the installation instructions must be adhered to.
Failure to do so could result in serious personal injury.
Step 1
Step 2
Figure 2
Figure 1
1
2 3 3
4
3
33
3
2
Wire
Access
14"
8 5/8"
Base Plate Connectors #1
Projector Mount Ceiling Plate 1
Plate 1
Plate 2
Base Plate Connectors #1 and Projector Mount Ceiling
Plate 1 with
ceiling mounting holes #2.
Horizontal Adjustment Plate 2 (Base Plate Connector
Holes #3).
2
Ceiling Wire
Access
7 5/8"
10 5/8"
Insert Base Plate connectors #1 into the lateral positioning slots
#3 as shown in
#4 from the underside of Plate 1. The lateral positioning
slots will give you 2 1/4" inches of lateral adjustment for projector
alignment.
4
Base plate connector holes #3 provide 15 degrees of horizontal
rotation adjustment.
Attach horizontal adjustment Plate 2 to projector mount ceiling
Plate 1 using the four (4) 3/8" (inch) nuts and washers provided.
1. Four (4) 3/8 (inch) nuts
2. Four (4) 3/8 (inch) flat washers
3. Two (2) 8 (mm) screws
4. Eleven (11) 6 (mm) screws
5. Eight (8) 6 (mm) rubber washers
6. One (1) Ceiling Mount #1
7. Two (2) Base Plate Connectors
8. One (1) Horizontal Tilt Plate #2
9. One (1) Horizontal Tilt Plate #3
10. One (1) Projector Plate #4          
Horizontal Tilt (yaw)  +/- 10 degrees
Vertical Tilt (tilt)    +/- 20 degrees
Rotation    +/- 15 degrees
Lateral Shift    +/- 2 1/4 inches
Maximum Load Allowance  450 Lbs.
MOUNT20 PROJECTOR MOUNT INSTALLATION INSTRUCTIONS continued
Step 3
Step 2 B
Step 3 B
Figure 3
Figure 4 Figure 6
Figure 5
Step 4
Wire
Access
Wire
Access
1
3
1
2
2
2
2
2 2
2
2
2
3
1
3
Plate 3 Plate 4
Plates 1 & 2 Plate 3
Horizontal Adjustment Plate 2 (Figure 2) attached to
Projector Mount Ceiling Plate 1.
Horizontal Tilting Plate 3 Projector Mounting Plate 4
Install the combined plates (above) securely to the ceiling
structure in accordance with local commercial building
standards.
Use suitable hardware in adequate quantity and size depending
on the installation requirements. (Please note that Projector
VP-12SX weighs 28.6 lbs. (13 kgs).
Attach Horizontal Tilting Plate 3 to the previously combined
plates (already installed on ceiling) using the two (2) 8 (mm)
screws and four (4)
6
(mm) screws provided, as indicated
in Figure
4. Install two (2) 6 (mm) screws with rubber
spacers and
metal washers into the welded metal studs
(indicated #1).
Holes for 6mm screws
Holes for 8mm screws
Holes for 6mm screws with rubber washer and steel washer
Indicates Forward
Positioning of Mount
Indicates Forward
Positioning of Mount
Tilting Capability
Tilting Capability
Horizontal Tilting Plate 3 Attached to Plates 1 and 2.
The newly combined Plate 3 provides 10 0 degrees of
horizontal tilt. When positioned, tighten with screws
provided.
12 1/4"
17"
continued over
Invert the projector and place it on a soft and flat
surface. Align the three (3) rubber spacers provided
with the three (3) 6(mm) mounting holes on the
projector and secure with three (3) 6(mm) screws
provided.
mounting holes

Specyfikacje produktu

Marka: Marantz
Kategoria: Projektor
Model: MOUNT20BL

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Marantz MOUNT20BL, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Projektor Marantz

Marantz

Marantz VP-11S2 Instrukcja

17 Sierpnia 2024
Marantz

Marantz MOUNT20BL Instrukcja

4 Lipca 2024

Instrukcje Projektor

Najnowsze instrukcje dla Projektor

Acer

Acer X137WH Instrukcja

14 Października 2024
Hitachi

Hitachi CP-A352WNM Instrukcja

14 Października 2024
Barco

Barco Thor Instrukcja

14 Października 2024
NEC

NEC NP-M283X Instrukcja

14 Października 2024
Epson

Epson PowerLite 5520W Instrukcja

13 Października 2024
Epson

Epson EX3220 Instrukcja

12 Października 2024
Acer

Acer X112 Instrukcja

12 Października 2024
Epson

Epson PowerLite Pro G6770WUNL Instrukcja

12 Października 2024
3M

3M X36i Instrukcja

11 Października 2024
Optoma

Optoma EP774 Instrukcja

11 Października 2024