Instrukcja obsługi Makita RP2302FC
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Makita RP2302FC (1 stron) w kategorii frezarka. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-000288 Rev01
©2009 Milestone AV Technologies,
a Duchossois Group Company
05/09
SSB-228, SSM-228, SLB-228 and SLM-228 Interface Brackets
SSB-228, SSM-228, SLB-228 and SLM-228 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place nylon spacers on bottom of projector and align them with threaded inserts.
4. Place the interface bracket onto the bottom of the projector and align it with the holes in the bracket with the threaded inserts and nylon
spacers on the bottom of the projector.
5. Position M4 x 20mm pan head mounting screws with M4 washers, and M4 x 20mm flat head mounting screws into the mounting holes.
Tighten all fasteners at this time, securing the bracket to the projector.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation
instructions in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (3) Washer, Flat, M4
(4) 10-24 Thumb Nuts ** (3) Screw, Phillips Pan Head, M4 x 20mm
(1) All-Points Security Kit (2) Screw, Phillips Flat Head, M4 x 20mm
(5) Spacer, Nylon, .500 OD x.194 ID x .500
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style
interface bracket installation.
SLB-228 SLM-228
(Note: SSB-style interfac
e
b
r
a
c
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(
N
o
t
e
:
S
S
M
-
s
t
y
l
e
i
n
t
e
r
f
a
c
e
b
r
a
c
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
Towards front of
projector
Towards front of
projector
Specyfikacje produktu
| Marka: | Makita |
| Kategoria: | frezarka |
| Model: | RP2302FC |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Makita RP2302FC, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje frezarka Makita
15 Października 2024
2 Października 2024
2 Października 2024
22 Września 2024
16 Września 2024
5 Września 2024
29 Sierpnia 2024
28 Sierpnia 2024
5 Lipca 2024
5 Lipca 2024
Instrukcje frezarka
- frezarka Worx
- frezarka Bosch
- frezarka Parkside
- frezarka Black & Decker
- frezarka Scheppach
- frezarka Grizzly
- frezarka DeWalt
- frezarka Einhell
- frezarka Ozito
- frezarka Flex
- frezarka Trotec
- frezarka Meec Tools
- frezarka AL-KO
- frezarka Texas
- frezarka Mafell
- frezarka Ferm
- frezarka Hitachi
- frezarka PowerPlus
- frezarka Vonroc
- frezarka Kinzo
- frezarka Trend
- frezarka Maktec
- frezarka Bort
- frezarka Power Craft
- frezarka Eibenstock
- frezarka Topcraft
- frezarka Carat
- frezarka Duro
- frezarka Truper
- frezarka Bruder Mannesmann
- frezarka Rupes
- frezarka Holzmann
- frezarka Elu
- frezarka Triton
- frezarka Felisatti
- frezarka Toledo
- frezarka CMT Orange Tools
Najnowsze instrukcje dla frezarka
14 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
4 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
1 Października 2024
1 Października 2024